We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Gaffney, SC 29340
Sam
Job Details:
04/29/2024
Found unit not cleaning dishes. Found unit has error codes for pump and motor and heater. Tried cycling unit. Nothing happened to recirculate water and heat. Will order parts.; ordrng 1 W11613480 (Pump and motor) and 1 W10518394 (Heater) and 1 W11637583 (Control)
We serviced a
KITCHENAID MW OVEN COMBO
Model KOCE500ESS22
Near Burnsville, NC 28714
Matt
Job Details:
04/29/2024
Helped K.R on this one.
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Gaffney, SC 29340
Sam
Job Details:
04/29/2024
Installed hinges and hinge receptacles. Cycled unit through timed dry. Door closing properly. All functions pass.
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Mars Hill, NC 28754
Kari
Job Details:
04/29/2024
"Took quick pics, found tub full of water and the board with no lights. Found drain pump trying to run safety loop thats why the panel is blank. Manually cleared all water took drain pump down and found paper clip wrapped around impeller. Installed new drain pump ran diagnostics cycle unit checks ok; used 1 W10919003 (Drain pump) from stock"
We serviced a
WHIRLPOOL RANGE
Model WFE525S0JZ3
Near Anderson, SC 29625
Jerry D.
Job Details:
04/29/2024
"Door broken pieces missing, ordering, j13p; ordrng 1 W10746436 (Trim) and 1 W10746435 (Trim) and 1 W11242950 (Assy)"
We serviced a
WHIRLPOOL VENT HOOD
Model WVW53UC0LS0
Near Seneca, SC 29678
Frank
Job Details:
04/29/2024
A couple fan blade broke off bad vibration in unit.. ordering blower motor to replace; ordrng 1 W11351717 (Blower fan) and 1 Jobcodej13 (Job code j13)
We serviced a
WHIRLPOOL WASHER
Model WFW6605MC0
Near Seneca, SC 29672
Frank
Job Details:
04/29/2024
No errors present.. tested cycle leveled legs better.. working ok..
We serviced a
KITCHEN AID DISHWASHER
Model KDTM604KBS0
Near Seneca, SC 29672
Frank
Job Details:
04/29/2024
Replaced tub seal ran unit checked for leaking. no leaking found..
We serviced a
MAYTAG DRYER
Model MEDC465HW0
Near Liberty, SC 29657
Frank
Job Details:
04/29/2024
Tested cycle Temps go up to 200 down to 120 dropping 2-3! degrees per second..
We serviced a
JENN AIR REFRIGERATOR
Model JFFCC72EHL03
Near Easley, SC 29640
Frank
Job Details:
04/29/2024
Replaced door seal.. heated. Molded and checked for gqps.. looks ok.
We serviced a
JENN-AIR MW OVEN COMBO
Model JMW2430DP03
Near Greer, SC 29651
Chris
Job Details:
04/29/2024
Installed panel. Unit check is ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM12
Near Greer, SC 29651
Chris
Job Details:
04/29/2024
Installed new imk. Unit check is ok
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Lyman, SC 29365
Chris
Job Details:
04/29/2024
Unit has e5 fault in test 56. Freezer temp is at 8 degrees. Ordeing for repair ; ordrng 1 WPW10675033 (Control)
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS03
Near Piedmont, SC 29673
Jerry D.
Job Details:
04/29/2024
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
KITCHENAID MW OVEN COMBO
Model KOCE500ESS22
Near Burnsville, NC 28714
Kari
Job Details:
04/29/2024
Installed parts unit checks ok K1B2VG1NL2
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC703HPS05
Near Travelers Rest, SC 29690
Chris
Job Details:
04/29/2024
Found kinked water line in door. Removed door and re installed door . Unit check is ok . New labor authorization is k1b2s40nl1.5
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Greenville, SC 29617
Larry M.
Job Details:
04/29/2024
Found gap in freezer door indicating the door is bent. Ordering freezer door. ; O-emld tckt
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHV04
Near Easley, SC 29640
Frank
Job Details:
04/29/2024
Temp 0in fc.. E5 error tested 56.. harvest came up not completed.. all other functions ok in diag mode.. ordering the ce maker; ordrng 1 W11658802 (Ice maker) and 1 Jobcodel14 (Job code l14)
We serviced a
MAYTAG DRYER
Model MGD7100DC0
Near Lake Lure, NC 28746
Brian
Job Details:
04/29/2024
"Found unit vibrating really bad/loud. Inspected and found rear rollers, and idler pulley wheel, sticking and not spinning well. Roller Repair kit (4392067) needed. Quoted customer 357.54 to complete repairs. Customer wished to proceed. Installed roller kit, and cleaned lent from unit. Tested unit and found all operations ok at this time with no leaks detected. Collected total. ; used 1 4392067 (Repair kit TS) from stock"
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Spartanburg, SC 29302
Sam
Job Details:
04/26/2024
Found units front right burner not igniting found that unit is getting gas and electrode is sparking. Found units burner not close enough to make contact with burner base to ignite gas. Adjusted screws underneath burner base to the gas line and electrode mount for re alignment. Cycled all burners after adjusting. Burner igniting every time without fail. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WSF26C3EXW01
Near Cowpens, SC 29330
Matt
Job Details:
04/26/2024
"Found freezer at -3 degrees. Optics pass on ice container. Door switches check ok. Cycled I've maker. Ice maker cycled, released ice and filled with water properly. All functions pass. There are several service pointers on this model having ice maker issues. Advised customer."
We serviced a
WHIRLPOOL FREEZER
Model WRS315SDHZ18
Near Anderson, SC 29626
Jerry D.
Job Details:
04/26/2024
"Wire harness inoperable, ordering, j13; ordrng 1 W11573117 (Assembly)"
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Asheville, NC 28804
Kari
Job Details:
04/26/2024
"Took quick pics, found new motor showing 7-2 code. Found new motor is locked up. Installed new motor. Ran diagnostic cycle. It completed cycle. Also ran normal cycle and found it fills and motor runs. Unit checks ok"
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Asheville, NC 28803
Kari
Job Details:
04/26/2024
Installed parts unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ00
Near Asheville, NC 28805
Kari
Job Details:
04/26/2024
"Took quick pics, found unit room temp in both compartments but all 3 fans are working. Took back panel off and both evap covers, ran test 4 found the 3 way moves and the compressor running but no frost pattern formed on either evap. Tapped compressor and found unit in 30in vacuum. Filled with 5.5 oz of 134a found frost patterned starting to form sprayed big blue on coils and joints found there is a leak in ff evap. Gave cust est of $1,719.19 for complete sealed system repair. Customer is going to call whirlpool to see if they will cover anything additional. Had office run cc for $150 TC and email receipt ; used 1 BPV31 (Tap) from stock"
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Spartanburg, SC 29306
Matt
Job Details:
04/26/2024
Helped S.R on this one.
We serviced a
WHIRLPOOL WASHER
Model MVWC565FW2
Near Spartanburg, SC 29302
Sam
Job Details:
04/26/2024
Uninstalled units agitator screw but units agitator/wash plate would not release after multiple tries unit will need washplate in addition to inner basket and suspension. Gave customer estimate of 537.51 customer declined estimate said it would probably be better to just buy a new one. Put unit back together and back in original position re leveled feet of unit to help with shaking until the customer buys a new one. Collected trip charge of 125.00.
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Spartanburg, SC 29306
Sam
Job Details:
04/26/2024
"Installed all parts. Cycled unit through quick wash. Unit fills with water, agitates, drains and spins. No abnormal shaking or violent banging into walls. All functions pass."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHV04
Near Swannanoa, NC 28778
Kari
Job Details:
04/26/2024
Installed parts unit checks ok
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Simpsonville, SC 29680
Carl
Job Details:
04/26/2024
Cycled unit thru diagnostics no error codes ran a diagnostic cycle and ran a regular cycle to ck operation unit ck ok what customer hears is normal pump noise
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ01
Near Simpsonville, SC 29680
Carl
Job Details:
04/26/2024
"Installed new control ,harness and thurmister cycled unit ck ok"
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Spartanburg, SC 29301
Sam
Job Details:
04/26/2024
"Found units timer and knob cracked. Replaced timer and knob. Cycled unit through timed dry. Units starts, tumbles and heats. All functions pass."
We serviced a
WHIRLPOOL WASHER
Model WFW5605MC1
Near Spartanburg, SC 29303
Sam
Job Details:
04/26/2024
"Found unit making abnormal and loud rattling noise when in spin with load. Took panel off to look for anything out of the ordinary, everything appears normal. Checked for error codes no error codes found. Will order parts.; ordrng 1 W11354541 (Stator) and 1 W11314361 (Rotor) and 1 W11557803 (Screw)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPB2
Near Greenville, SC 29611
Larry M.
Job Details:
04/26/2024
Found blockage at trash compactor. Removed blockage. Checks o.k
We serviced a
MAYTAG WASHER
Model MVW6200KW3
Near Greenville, SC 29607
Larry M.
Job Details:
04/26/2024
Installed inner basket and suspension. Customer states she was promised that splutch kit and belt would be replaced as well. Ordering splutch kit and belt. ; ordrng 1 W10721967 (Cam) and 1 WPW10006384 (Belt)
We serviced a
WHIRLPOOL DISHWASHER
Model KDTE334GPS0
Near Greenville, SC 29617
Larry M.
Job Details:
04/26/2024
"Ran test cycle. Found motor making noise, quoted customer bluebook quote of $569 to replace sump pump and motor. Customer declined repair at this time; ordrng 1 W11178672 (Sump pump and motor) and 1 J13jobcode (J13 job code)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Gaffney, SC 29340
Matt
Job Details:
04/26/2024
Found ice in freezer fan. Found ice bridging. Will order pressure reducer.; ordrng 1 L14jobcode (L14 job code) and 1 W10786952 (Pressure reducer) and 1 W10267701rp (Water line)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM08
Near Hendersonville, NC 28792
Brian
Job Details:
04/26/2024
"Installed parts ordered. Tested and found all operations ok at this time, with no leaks detected."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS10
Near Fletcher, NC 28732
Brian
Job Details:
04/26/2024
"Customer said unit started working again. Tested and found all fans running and a good frost pattern. Damper operations ok. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Asheville, NC 28803
Brian
Job Details:
04/26/2024
Attempted to replace wash motor. Could not remove unit from counter. I informed customer they would have to make unit accessible to be able to repair. Customer understood and will call us when issue has been resolved. ; O-emld tckt
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706EBS01
Near Pickens, SC 29671
Frank
Job Details:
04/26/2024
EVAP frozen up.. needs fc gasket and EVAP motor.. bb quoted$725.54.. defrosted EVAP..$362.77 owe $362.77; saved tckt
We serviced a
JENN-AIR MICROWAVE
Model JMW2430IM03
Near Pickens, SC 29671
Frank
Job Details:
04/26/2024
F2e1 error ordering console.; ordrng 1 W11460597 (Console) and 1 Jobcodej13 (Job code j13)
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Easley, SC 29640
Frank
Job Details:
04/26/2024
Replaced knob and timer.. original broke.. tested working ok
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Liberty, SC 29657
Frank
Job Details:
04/26/2024
Replaced parts didn't need console.. tested unit working ok..
We serviced a
WHIRLPOOL DISHWASHER
Model KDTE334GP0
Near Travelers Rest, SC 29690
Larry M.
Job Details:
04/26/2024
Found Ui unresponsive. Couldnt check for error codesButtons will not respond. Ordering Ui and control.; ordrng 1 W11120155 (Main control) and 1 W11165145 (Ui console)
We serviced a
MAYTAG WASHER
Model MVW5430MW0
Near Seneca, SC 29678
Frank
Job Details:
04/26/2024
Replaced harness and control. Pump now getting 120v not working.replaced drain pump working ok.. tested quick cycle operating good.
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Townville, SC 29689
Frank
Job Details:
04/26/2024
Tub bouncing around. Rear shock dampers broken off. Need to replace back shocks..; ordrng 2 W11316766 (Dampers)s and 1 Jobcodel14 (Job code l14)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ05
Near Townville, SC 29689
Frank
Job Details:
04/26/2024
Replaced ice maker.. cycled filled with water ok.
We serviced a
WHIRLPOOL RANGE
Model WFG535S0LZ5
Near Fountain Inn, SC 29644
Carl
Job Details:
04/26/2024
Installed new top
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ04
Near Simpsonville, SC 29681
Carl
Job Details:
04/26/2024
"Ran diagnostics and tests56,45,57,58 error f5 installed new imk cycled unit to ck operation and had a good fill unit ck ok"
We serviced a
KITCHEN AID RANGE
Model KSEB900ESS3
Near Pendleton, SC 29670
Jerry D.
Job Details:
04/26/2024
"Installed blower sent preid, cycled unit through test and unit checks ok"
We serviced a
KITCHENAID MICROWAVE
Model KMBS104ESS03
Near Fountain Inn, SC 29644
Jerry D.
Job Details:
04/26/2024
"Door not shutting tight , service bulletin, ordering, j13; ordrng 1 W10731697 (Door)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHW4
Near Fountain Inn, SC 29644
Jerry D.
Job Details:
04/26/2024
Installed listed parts cycled unit through test and no leaks found unit checks ok
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF606ESS00
Near Simpsonville, SC 29681
Jerry D.
Job Details:
04/26/2024
"Fan motor shorted out , controller shorted, unit overheated and clogged, not repairable, 125.00"
We serviced a
WHIRLPOOL WASHER
Model WFW8620HC2
Near Simpsonville, SC 29681
Jerry D.
Job Details:
04/26/2024
"Valve inoperable installed valve sent preid cycled unit through test and no leaks found unit checks ok , 289.00"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFC704FBS03
Near Piedmont, SC 29673
Jerry D.
Job Details:
04/26/2024
"Found upper evaperator froze over, fan. Motor inoperable, cntrl not responding to commands, estimate, 1.128.00, customer will call, w11330486 interface, w11533213 Cntrl, w11395558 assembly, 125.00"
We serviced a
WHIRLPOOL RANGE
Model WFG505M0MS0
Near Lyman, SC 29365
Chris
Job Details:
04/26/2024
Installed new parts. Unit check is ok
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW0
Near Taylors, SC 29687
Chris
Job Details:
04/26/2024
Unit has loud pop from drive train. Ordeing for repair ; ordrng 1 W11195971 (Stator) and 1 W10754448 (Clutch) and 1 Q16
We serviced a
ELECTROLUX WASHER
Model EIFLW55HIW0
Near Greer, SC 29651
Chris
Job Details:
04/26/2024
Customer states unit will leave standing water in tub. Unit leaks and floors and rear wall have damage due to wash failure..water valve has heavy corrosion build up . Advised customer there may be more to this repair besides valve. Gave customer a bluebook estimate for repair at $571.38. Cusotmer denied repair
We serviced a
MAYTAG DRYER
Model MEDC465HW0
Near Greer, SC 29651
Chris
Job Details:
04/26/2024
Unit has open cut off fuse and thermostat. Have customer a bluebook estimate for repair at 363.31. Installed new parts. Unit check is ok
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Greer, SC 29650
Chris
Job Details:
04/26/2024
Installed new parts. Unit check is ok
We serviced a
MAYTAG M/W OTR
Model MMV1175JZ0
Near Greenville, SC 29615
Chris
Job Details:
04/26/2024
Unit flashes f1 e4 fault. Unit needs control. Gave customer a bluebook estimate at $377.56. Customer denied repair
We serviced a
WHIRLPOOL DRYER
Model WED8500DC4
Near Arden, NC 28704
Brian
Job Details:
04/26/2024
Installed new door catch. Tested and found all operations ok at this time.
We serviced a
MAYTAG DRYER
Model MGD7230HW3
Near Asheville, NC 28801
Brian
Job Details:
04/26/2024
"Inspected and found unit heating and tumbling but with very poor airflow. Removed vent line from unit and found airflow ok, indicating a clogged or obstruction within vent line itself. Recommended customer have vent lines cleaned. Customer understood."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ
Near Greenwood, SC 29646
Jerry D.
Job Details:
04/25/2024
Mrs cancelled
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Honea Path, SC 29654
Jerry D.
Job Details:
04/25/2024
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
WHIRLPOOL DRYER
Model WED6150PB0
Near Honea Path, SC 29654
Jerry D.
Job Details:
04/25/2024
"Door catch bent, installed w11224630 from truck stock cycled unit through test and unit checks ok"
We serviced a
WHIRLPOOL WASHER
Model WTW4655JW2
Near Asheville, NC 28803
Brian
Job Details:
04/25/2024
"Unit in 323. Found no saved error codes. Tested unit in diagnostics and found scraping sound coming from under unit. Also found rear panel vibrating when draining. Adjusted rear panel. Inspected and found a piece of foreign plastic under pulley shield. Removed and calibrated. Tested unit and found all operations ok at this time, with no leaks detected."
We serviced a
MAYTAG DRYER
Model MEDB835DC4
Near Greer, SC 29651
Chris
Job Details:
04/25/2024
Unit needs maintenance kit. Gave Cusotmer a bluebook estimate for repair at $447.45. Installed new parts . Unit check is ok
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS10
Near Belton, SC 29627
Jerry D.
Job Details:
04/25/2024
"Opened new door box , customer found defects, ordering, j13; ordrng 1 W11173813 (Door)"
We serviced a
KITCHENAID DISHWASHER
Model KDTE304LPA1
Near Leicester, NC 28748
Kari
Job Details:
04/25/2024
"Took quick pics, found unit showing 7-2 and 9-2 codes. Found motor has correct ohms but not turn on need pump for repair. Prescheduled for 5/6 PM; ordrng 1 W11460946 (Sup assembly) and 1 L14 (Job code)"
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC703HPS05
Near Waynesville, NC 28786
Kari
Job Details:
04/25/2024
"Took quick pics, found unit resivor freezing found the gasket around evap styrofoam was peeled away. Corrected gasket and sealed gasket down with rtv. Unit checks ok ; used 1 W10841140 (Silicone) from stock"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ1
Near Waynesville, NC 28786
Kari
Job Details:
04/25/2024
Installed parts unit checks ok
We serviced a
WHIRLPOOL WASHER
Model MVW6500MW0
Near Etowah, NC 28729
Brian
Job Details:
04/25/2024
"Found lid strike broken. Replaced strike (w11457841) and tested unit in diagnostics and found all operations ok at this time, with no leaks detected. Did not move unit. ; used 1 w11457841 (Strike TS) from stock"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Mountain Rest, SC 29664
Frank
Job Details:
04/25/2024
Lid lock clicking not locking..Replaced lid switch.tested working ok
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Walhalla, SC 29691
Frank
Job Details:
04/25/2024
Heated up to 160 degrees. Dropped slow.. cleaned out vent .. now heats to 200 drops 2-3 degrees per second. Heating and venting ok now.
We serviced a
JENN-AIR DISHWASHER
Model JDB9200CWP2
Near Seneca, SC 29672
Frank
Job Details:
04/25/2024
Replaced drain pump tested working ok not leaking
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Seneca, SC 29672
Frank
Job Details:
04/25/2024
Damper rattling making noise.. ordering... leveled and checked door seals ok.; ordrng 1 WPW10479155 (Damper) and 1 Jobcodel14 (Job code l14)
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Fountain Inn, SC 29644
Carl
Job Details:
04/25/2024
Installed new door gasket and sweep and adjuster levers cycled unit thru a test cycle to ck operation unit ck ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Simpsonville, SC 29681
Jerry D.
Job Details:
04/25/2024
"Auger Motor humming, imk broken, overfilled, ordering, j13; ordrng 1 W11359448 (Imk) and 1 W11307588 (Bracket) and 1 W10884561 (Motor)"
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Simpsonville, SC 29681
Jerry D.
Job Details:
04/25/2024
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Simpsonville, SC 29681
Jerry D.
Job Details:
04/25/2024
"Cutoff open, installed cutoff sent preid, cycled unit through test and vent ok, heat cycles are 198 and 112, unit chks ok"
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Simpsonville, SC 29681
Jerry D.
Job Details:
04/25/2024
"Cycled unit through test and no codes found, unit chks ok today, customer says sometimes unit wont respond and they have to reset breaker and usually unit will come back on, customer very upset, tline robert, volts and polarity good and connections ok, unit chks ok today, tline recommended teplacing interface and cntrl, ordering, j13; ordrng 1 W11577490 (Cntrl) and 1 W11164011 (Interface)"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF507HPS00
Near Hendersonville, NC 28791
Brian
Job Details:
04/25/2024
"Found top fresh food lights out and freezer door not sealing properly. Found service pointer regarding lights. Inspected freezer door,and found rails not functioning properly. Module kit (W11683244) and Bracket kit (W11668671); ordrng 1 W11683244 (Module kit) and 1 W11668671 (Bracket kit) and 1 Q16 (Job code)"
We serviced a
WHIRLPOOL FREEZER
Model WRT148FZDB05
Near Lake Lure, NC 28746
Brian
Job Details:
04/25/2024
Installed new name tag. All operations ok. Did not move unit.
We serviced a
AMANA DISHWASHER
Model ADB1400AMS1
Near Simpsonville, SC 29681
Jerry D.
Job Details:
04/25/2024
"Found drain pump inoperable, installed w10348269 from truck stock, cycled unit through test and no leaks found unit checks ok"
We serviced a
MAYTAG WASHER
Model MVW7230HW
Near Spartanburg, SC 29301
Sam
Job Details:
04/25/2024
"Installed all parts. Cycled unit through quick wash. Unit no longer makes grinding noise when in spin. All components working unit fills, drains, agitates and spins. all functions pass."
We serviced a
WHIRLPOOL RANGE
Model WFG550S0LZ4
Near Greenville, SC 29605
Carl
Job Details:
04/25/2024
Cycled unit to 350? ran for several cycles in temp @335 out @405 all the burners have good flames all functions to factory specs
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Lake Lure, NC 28746
Brian
Job Details:
04/25/2024
"Installed all parts ordered. Tested heater and all other functions. At this time, all operations ok with no leaks detected. ; O-emld tckt"
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Boiling Springs, SC 29316
Sam
Job Details:
04/25/2024
Found unit making a lot of noise. Checked diagnostics no error codes found. Ran unit through cycle checked for gear case grinding. Gear case checks ok. All connections secured on wires throughout machine. Found multiple feet of the machine not level. Leveled feet of machine. Cycled unit through quick wash with load. No more banging noise and violent shaking. All functions pass.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Boiling Springs, SC 29316
Sam
Job Details:
04/25/2024
Installed latch. cycled unit through diagnostics cycle and quick wash. All components working. All functions pass.
We serviced a
KITCHENAID DISHWASHER
Model KDTE104KPS1
Near Gaffney, SC 29341
Sam
Job Details:
04/25/2024
Installed all parts. Cycled unit through quick wash. All components working. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHB05
Near Sapphire, NC 28774
Frank
Job Details:
04/25/2024
Trained with Matt.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS04
Near Duncan, SC 29334
Matt
Job Details:
04/25/2024
Freezer temperature is -1. Ice maker runs and passed test 57. Optics pass. Ran test 45 and ice maker filled with water. Customer stated after new ice maker it dumped ice one time and never filled with water again. Will order controls ; ordrng 1 W11161172 (Control) and 1 W11501508 (User interface) and 1 L14jobcode (L14 job code)
We serviced a
MAYTAG RANGE
Model MGS8800FZ5
Near Greenville, SC 29617
Matt
Job Details:
04/25/2024
"Customer started unit will go cold and food comes out raw. 359,355,363,356,364,356.=average temperature is 358 Put unit on convect roast with a pan of water . After preheat the temperature dropped and just continued to drop. Convection element and fan check o.k door switch must be opening circuit causing burner to turn off.; ordrng 1 N15jobcode (N15 job code) and 1 W11511828 (Door switch)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHB05
Near Sapphire, NC 28774
Matt
Job Details:
04/25/2024
Helped F.C on this. Evacuated system. Replaced controls and sealed system parts. Pressure tested. Unit held pressure. Pulled vacuum and weighed in r600a
We serviced a
WHIRLPOOL WASHER
Model WTW5100HC3
Near Spartanburg, SC 29307
Sam
Job Details:
04/25/2024
Found unit not filling with water. Checked diagnostics found long fill error code. No loose connections to control water valve checks ok. Removed back panel found kink in pressure hose. Removed kink from pressure hose. Cycled unit through quick wash unit now fills with water and progresses cycle. All functions pass.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Greenville, SC 29617
Larry M.
Job Details:
04/25/2024
Replaced sump pump and motor assembly. Checks o.k
We serviced a
KITCHEN AID DISHWASHER
Model KDTE254ESS0
Near Greenville, SC 29605
Larry M.
Job Details:
04/25/2024
Verified sufficient power from breaker box. No response from main control. Could not check for fault codes. Pump clogged upQuoted customer bluebook quote of $838.39 to replace motor and control panel. Customer declined repair ; ordrng 1 J13jobcode (J 13 job code) and 1 WPW10455261 (Sump and motor) and 1 W10866124 (Control panel)
We serviced a
KITCHENAID DISHWASHER
Model KDTE254ESS2
Near Greenville, SC 29605
Larry M.
Job Details:
04/25/2024
"Found plastic melted onto heater, quoted customer $422.00 to replace heater. Partial payment of $211 received on first visit. Will collect rest on second visit ; ordrng 1 L14jobcode (L14 job code) and 1 W10703867 (Heater)"