We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Taylors, SC 29687
Chris
Job Details:
03/18/2024
Unit has moisture build up on mullion and door. Door has already been replaced. Door has been adjusted every way possible . Called tech line and spoke with Leon.leon advised to order foam seals. File number for call is 7738702367; ordrng 1 W11159728 (Foam)
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Greer, SC 29651
Chris
Job Details:
03/18/2024
Customer states unit gets off balance when trying to wash blankets and sheets. . Customer states they have no problem with everyday loads . Unit has off balance faults stored . Cleared faults. Ran automatic diagnostic cycle . Unit passes with no faults. Suspension is firm and planted . Wash basket has all holes punched through. Ran quick wash cycle with 8 towels. Unit works as designed. No faults. Customer loading procedure is the fault . No fault of unit. Unit check is ok
We serviced a
MAYTAG WASHER
Model MVW6500MW0
Near Greer, SC 29651
Chris
Job Details:
03/18/2024
Installed new parts. Unit check is ok
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS07
Near Greer, SC 29650
Chris
Job Details:
03/18/2024
Found torn gaskets . Ordeing for repair ; ordrng 2 W10830162 (Gasket)s
We serviced a
WHIRLPOOL REFRIGERATOR
Model JFFCF72DKL04
Near Greer, SC 29651
Chris
Job Details:
03/18/2024
Unit has torn gasket. Ordeing for repair ; ordrng 2 W10830046 (Gasket)s
We serviced a
WHIRLPOOL FREEZER
Model WRF767SDEM01
Near Inman, SC 29349
Chris
Job Details:
03/18/2024
Unit has led lights out in roof. Customer states he was told lights were covered under special project by customer service rep. Unit is out of serial range. Unit needs light harness. Gave customer a bluebook estimate for repair at $435.96. Installed new lights. Unit check is ok .
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FMDB09
Near Pickens, SC 29671
Frank
Job Details:
03/18/2024
Rc 41 degrees fc 20 degrees.. checked evaporator no good frost pattern icing up in top right corner by thermistor.. ordering EVAP and compressor; ordrng 1 W11582592 (Compressor) and 1 W11504415 (28a) and 1 W11504431 (28b) and 1 W11506619 (28c) and 1 W11506635 (28d) and 1 w11506635 (Access port) and 1 wpw10143759 (Drier) and 1 W11562258 (Evaporator) and 1 W11504419 (5a) and 1 W11504449 (5b) and 1 R600a (R600a) and 1 Sealedsystemtech (Sealed system tech) and 1 Sendfcwithma (Send fc with ma fo4 training) and 1 Jobcodex20 (Job code x20)
We serviced a
KITCHENAID ICE MACHINE
Model KUID308HPS01
Near Salem, SC 29676
Frank
Job Details:
03/18/2024
Replaced pump tested working ok.. ran through diagnostics all functions working ok
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near West Union, SC 29696
Frank
Job Details:
03/18/2024
Replaced valve.. water still hammering.. needs anti hammer arrestor.
We serviced a
KITCHENAID KITCHEN
Model KDTM404KPS1
Near West Union, SC 29696
Frank
Job Details:
03/18/2024
Replaced parts tested working ok.. checked for leaks.. no leaking. Running ok
We serviced a
KITCHENAID ICE MACHINE
Model KUIX335HPS00
Near Seneca, SC 29672
Frank
Job Details:
03/18/2024
Unit pulled out on arrival.. water not coming in fast needs valve.. bb quoted$473.80. paying $236.90. Owe 236.90; saved tckt
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ04
Near Pelzer, SC 29669
Jerry D.
Job Details:
03/18/2024
"Damper noises, ordering, j13; ordrng 1 W10479155 (Damper)"
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Pendleton, SC 29670
Frank
Job Details:
03/15/2024
Installed parts tested working ok.. spinning ok. Goes into wash ok
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Greenville, SC 29617
Larry M.
Job Details:
03/15/2024
"I replaced the main control and wiring harness unit checks, OK"
We serviced a
WHIRLPOOL COOKTOP
Model WCG97US0HS00
Near Greenville, SC 29617
Larry M.
Job Details:
03/15/2024
Found orifice tube clogged. And replaced cap. Checks ok
We serviced a
MAYTAG WASHER
Model MVW6500MBK0
Near Easley, SC 29642
Larry M.
Job Details:
03/15/2024
"Installed harness, ran test cycle. Checks o.k"
We serviced a
MAYTAG WASHER
Model MVWP575GW1
Near Moore, SC 29369
Sam
Job Details:
03/15/2024
Found units tub ring cracked. Will order tub ring.; ordrng 1 WPW10556325 (Tub ring)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Pickens, SC 29671
Frank
Job Details:
03/15/2024
Leaking from valve.. ordering reservoir in case tube doesn't come out valve and need to cut water tubes..; ordrng 1 W11579561 (Valve) and 1 Jobcodel14 (Job code l14) and 1 W11482382 (Reservoir)
We serviced a
MAYTAG WASHER
Model MVWC465HW4
Near Mountain Rest, SC 29664
Frank
Job Details:
03/15/2024
Brake squealing on down speed. Needs gearcase bb quoted 679$. Not repairing at this time
We serviced a
MAYTAG OVEN
Model MEW7627DH02
Near Mountain Rest, SC 29664
Frank
Job Details:
03/15/2024
Replaced control and sensors calibrated. Tested working ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Anderson, SC 29621
Jerry D.
Job Details:
03/15/2024
"Installed listed parts cycled unit through test and no leaks found unit checks ok, advised customer about high water pressure"
We serviced a
WHIRLPOOL RANGE
Model Kfgg500ess1
Near Gaffney, SC 29341
Sam
Job Details:
03/15/2024
Found unit has f1e1 error code explained to customer unit would need control and possibly other parts. Gave customer estimate of 625.00 customer declined estimate. Customer said they would just go buy a new range. Collected trip charge of 150.00
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Spartanburg, SC 29303
Sam
Job Details:
03/15/2024
Installed parts. Cycled unit through quick wash. All components working. All functions pass.
We serviced a
WHIRLPOOL DRYER
Model WED4850HW0
Near Lyman, SC 29365
Chris
Job Details:
03/15/2024
Unit dies mid cycle. Ordeing parts for repair ; ordrng 1 279827 (Motor) and 1 WP694089 (Wheel)
We serviced a
AMANA WASHER
Model MVW7230HW1
Near East Flat Rock, NC 28726
Brian
Job Details:
03/15/2024
"Installed new lid strike. Calibrated and tested unit observing for leaks and proper functions. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
WHIRLPOOL RANGE
Model WFG505M0MS0
Near Hendersonville, NC 28792
Brian
Job Details:
03/15/2024
Installed new oven bottom and gasket. Tested unit and found all operations ok with no gas leaks detected. Did not move unit.
We serviced a
AMANA REFRIGERATOR
Model ART318FFDB10
Near Asheville, NC 28803
Brian
Job Details:
03/15/2024
Installed new door switch. Tested and found all operations ok at this time with no leaks detected. Did not move unit.
We serviced a
WHIRLPOOL WASHER
Model WFW5620HW0
Near Asheville, NC 28805
Brian
Job Details:
03/15/2024
"Tenant Maureen 828-423-5507. Found f3e2 (wash ntc open or shorted) f0e5 (off balance load). When starting a cycle or test cycle, f3e2 code comes up and unit worst start. Inspected and found heater and wires going to temp sensor broken. Installed new heater and repaired wire best I could to get unit to function. New Lower harness (W11550159) needed.; ordrng 1 W11550159 (Lower harness) and 1 L14 (Job code)"
We serviced a
MAYTAG DRYER
Model MED7230HW1
Near Anderson, SC 29621
Jerry D.
Job Details:
03/15/2024
"Heaterand thermostat open, installed heater and thermostat sent preid, cycled unit through test and unit checks ok, 526.00"
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Anderson, SC 29625
Jerry D.
Job Details:
03/15/2024
"Installed valve sent preid, cycled unit through test and no leaks found unit checks ok"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS06
Near Asheville, NC 28804
Brian
Job Details:
03/15/2024
"Found freezer door getting hung up, when closing. Inspected and found no visible discrepancies. Also found right hand fresh food door not closing properly. Customer also said that unit makes a squealing sound. Unit was in defrost when I arrived. Tested compressor and all other moving parts. Was unable to recreate noise at this time. Customer does have unit set to the coldest settings. I informed customer that this could cause unit run run longer and possibly make more noises than usual, as well as other potential issues. Recommended customer try to get a recording of noise. Left hand bracket (W11241580) RH bracket (W11241268) rh closer (W11188796) door stop (W11243377) RH hinge (W10816323) bushing (W11223833) rh hinge (W11032620) needed. ; ordrng 1 W11241580 (LH bracket) and 1 W11241268 (RH Bracket) and 1 W11188796 (RH closer) and 1 W11243377 (Door stop) and 1 W10816323 (RH hinge) and 1 W11223833 (Bushing) and 1 L14 (Job code) and 1 W11032620 (Hinge)"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ2
Near Piedmont, SC 29673
Jerry D.
Job Details:
03/15/2024
Roaches installed listed parts cycled unit through test and unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ11
Near Gaffney, SC 29340
Matt
Job Details:
03/15/2024
Found evaporator frozen. Put unit in defrost and found defrost sensor is good heater pulling the correct wastage. Replaced control. Checks o.k
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFC704FBS00
Near Gaffney, SC 29340
Matt
Job Details:
03/15/2024
Installed new ice maker full tube cycled ice maker and ice maker filled properly.
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ2
Near Lyman, SC 29365
Chris
Job Details:
03/15/2024
Found stuck check valve. Removed drain hose and cleared check valve. Unit check is ok . No leaks
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ08
Near Spartanburg, SC 29303
Matt
Job Details:
03/15/2024
Evacuated system. Replaced compressor and evaporator. Pressure tested. Unit held pressure. Weighed in 1.87 ounces of r600a checks o.kTrade care authorization w1ani50nL1.5
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEYM04
Near Asheville, NC 28805
Kari
Job Details:
03/15/2024
"Took quick pics, found unit door very low on rh ff scraping freezer door when opened. Found the bottom of the door cracked and missing. Would need door for repair. Gave cust est of $792.84 customer is going to do some shopping and give us a call back if they want us to order the door. Collected TC via check for $150 emailed receipt"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ08
Near Black Mountain, NC 28711
Kari
Job Details:
03/15/2024
"Took quick pics, found unit not dispensing ice. Found auger motor stripped and so is yolk need parts for repair. Prescheduled for 3/22 AM; ordrng 1 W11671282 (Auger) and 1 WP63052-2 (Yolk) and 1 N15 (Job code)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFC302ESS06
Near Black Mountain, NC 28711
Kari
Job Details:
03/15/2024
"7738687265 LiamTook quick pics, found unit frosted over on fz evap. Cover has light fluffy frost. Defrosted off ice with steamer and took cover off and found the heater pulls 3.4 amps and is heating. Found thermistors to be good and resistance is correct. Called techline and spoke with Liam. He said to change control again. Need parts for repair ; ordrng 1 WPW10120827 (Control) and 1 N15 (Job code)"
We serviced a
MAYTAG WASHER
Model MHWE300VF00
Near Pelzer, SC 29669
Jerry D.
Job Details:
03/15/2024
4342580198682486 10/ 26. 781; ordrng 1 Wpw10730972 (Pump)
We serviced a
JENN-AIR REFRIGERATOR
Model JFFCC72EHL02
Near Simpsonville, SC 29681
Jerry D.
Job Details:
03/15/2024
"Recoverd approximately 3 oz of refrigerant, Installed listed parts pulled 30 inches of refrigerant, charged 4.5 oz of liquid on high side, good frost pattern on evaperator, temps coming down rapidly unit chks ok"
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Spartanburg, SC 29301
Sam
Job Details:
03/15/2024
Installed suspension and inner tub. Cycled unit through quick wash. All components working. Unit does not shake violently anymore. All functions pass.
We serviced a
WHIRLPOOL RANGE
Model WFG535S0lZ4
Near Easley, SC 29642
Larry M.
Job Details:
03/15/2024
"Found igniter not lighting, ordering spark module and main control ; ordrng 1 WPW10475149 (Spark module) and 1 W11620570 (Main control)"
We serviced a
MAYTAG WASHER
Model MVWB765FW3
Near Simpsonville, SC 29680
Carl
Job Details:
03/15/2024
Ran diagnostics cycle got error f7e9 locked rotor remove rotor and ck slider xk good moved freely also had a few out of balance codes and a stuck button error ran a test cycle unit performed to factory specs unit ck ok
We serviced a
KITCHEN AID RANGE
Model KSDB900ESS0
Near Simpsonville, SC 29681
Carl
Job Details:
03/15/2024
Ran diagnostics ck all connections and ck p6 ck ok incoming power to board cleared error codes and reset control board sr# 7738689600 cqlled tech line went thru tests bad control; ordrng 1 W11099784 (Acu)
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Lyman, SC 29365
Chris
Job Details:
03/15/2024
Customer states she has trouble cooking cornbread and unit takes one hour to make said dish. Customer states unit light every time. Unit has no stored faults. Preheated oven with weighted thermocouple and set unit at 350. Unit hit target temp in 4 mins and 30 seconds as noted in pictures . Unit rested at 353 degrees. Opened door and let heat out. Unit ignited and came back up to 347 degrees . Customer feels oven doesnt cook hot enough . Customer present at temp readings. Calibrated oven plus 15. Showed customer how to calibrate unit. Unit check is ok
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS09
Near Spartanburg, SC 29301
Sam
Job Details:
03/15/2024
"Installed parts. Cycled units light, fan, heat, and turntable all working fine. All functions pass. 2 man authorization w1anln1nl2"
We serviced a
MAYTAG DRYER
Model MEDP575GW1
Near Moore, SC 29369
Sam
Job Details:
03/15/2024
Found fabric seal of drum peeled off of units drum. Will order parts.; ordrng 1 W10545923 (Drum)
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Moore, SC 29369
Sam
Job Details:
03/15/2024
Found unit not washing clothes well. Found agitator screw loose. No obvious stripping or cracks found anywhere on gear case shaft or agitator. Tightened agitator screw. Cycled unit through quick wash. All functions pass agitator no longer loose. All functions pass.
We serviced a
KITCHEN AID DISHWASHER
Model KDTM604KPS0
Near Greenville, SC 29609
Carl
Job Details:
03/15/2024
Found top rack manifold damaged c1; saved tckt
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ2
Near Easley, SC 29642
Larry M.
Job Details:
03/15/2024
Replaced main control. All functions pass.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF331PAHS1
Near Greer, SC 29651
Chris
Job Details:
03/15/2024
Installed new parts. Unit check is ok . No leaks
We serviced a
KITCHEN AID REFRIGERATOR
Model KRSC503ESS01
Near Greer, SC 29650
Chris
Job Details:
03/15/2024
Installed new door. Unit check is ok . No leaks. New authorization is k1anfv0xpl2
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF507ESS01
Near Taylors, SC 29687
Chris
Job Details:
03/15/2024
Unit doesnt make ice. Unit has e5 fault in test 56. Freezer temp is at 38 degrees and doesnt freeze liquids . Freezer evap doesnt have full frost pattern . Unit has sealed system failure. Customer denied further repair
We serviced a
WHIRLPOOL OVEN
Model WOD77EC0HS20
Near Duncan, SC 29334
Matt
Job Details:
03/15/2024
Found right side of ovens out of the cabinet. Was able to reinstall. Customer also losing clock function. Gave customer blue book estimate to replace console. 1674.00. Customer is going to update product through the app to see if it fixed it.
We serviced a
MAYTAG WASHER
Model MVWB765FC3
Near Travelers Rest, SC 29690
Larry M.
Job Details:
03/15/2024
Found gearcase slinging grease causing out of balance load. Found rotor state of balance. Ordering gearcase; ordrng 1 W11393685 (Gearcase)
We serviced a
SPEED QUEEN WASHER
Model AWNE9RSN116TW01
Near Greer, SC 29650
Matt
Job Details:
03/14/2024
"Replaced valve. Checked profession on hot, cold and warm. All functions pass. No dripping when finished."
We serviced a
WHIRLPOOL DRYER
Model WED8127LW2
Near Boiling Springs, SC 29316
Sam
Job Details:
03/14/2024
"Customer complaint is that unit is continuing the previous issue with cutting off after a few minutes of trying to dry clothes. Called techline, techline said that units reading at board to moisture sensor reads good resistance and since unit has no error codes advises me to tell customer that unit is working and to not use too little of a load because clothes will not hit moisture sensor properly and to not use too big of a load because that will cause the unit to heat too fast and stop it as well.File number # 7738189869"
We serviced a
WHIRLPOOL DISHWASHER
Model MDB4949SKZ2
Near Maggie Valley, NC 28751
Kari
Job Details:
03/14/2024
"Took quick pics, found unit showing no codes, found when running it in a diagnostic cycle. It runs fine until you get to step six and then the motor starts to get really loud and produce a bit of an electrical smell removed all the water from the unit unplugged it took motor apart to see if there was anything stuck in the cartridge, everything looks clear and everything is clear from the drain pump. It also looks like the diverter disc is in how its supposed to be found that the motor must be locking up would need the motor for repair but since the motor is showing on back order with no expected ETA. Customer called Whirlpool and Whirlpool is exchanging the unit"
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Six Mile, SC 29682
Frank
Job Details:
03/14/2024
Console display shutting off and not responding.. ordering control and ui...; ordrng 1 W11618917 (Control board) and 1 W11413567 (Panel control)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ06
Near Seneca, SC 29678
Frank
Job Details:
03/14/2024
50 degrees in rc. 0 in fc.. EVAP good frost on it not freezing up.. EVAP fan running and running in diagnostics mode. ; ordrng 1 W11645127 (Diffuser) and 1 W11566891 (Control board) and 1 WPW10384183 (Thermistor) and 1 Jobcodel14 (Job code l14)
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKV2
Near Asheville, NC 28803
Brian
Job Details:
03/14/2024
"F8e4 (overfill switch) F9e2 (drain motor problem) Fae2 (vent problem). Found evidence of water in drip pan, under unit. Tested unit and found excess suds in unit, without adding any. Cleared suds and tested multiple times observing for leaks and found none. At this time, unit is functioning as designed. Reviewed proper loading procedures and detergent use with customer. Customer understood. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
WHIRLPOOL WASHER
Model MVWC565FW3
Near Asheville, NC 28804
Brian
Job Details:
03/14/2024
"Found f7e5 (shifter fault). Found cam getting stuck. Tested unit and found inlet hose behind unit, leaking. It has a pin hole. Also found cam getting stuck, preventing unit from starting. Customer said they will get a new fill hose. New Cam(W10721967) needed. Quoted customer 278.17 to complete repairs. Customer wished to proceed with repair. Installed new cam and calibrated unit and tested. At this time, all operations ok, other than fill hose, with no leaks detected. Collected total. ; used 1 W10721967 (Cam TS) from stock"
We serviced a
WHIRLPOOL WASHER
Model WTW6157PW0
Near Arden, NC 28704
Brian
Job Details:
03/14/2024
"Installed main control and fascia. Tested unit observing for leaks and proper functions. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW3
Near Abbeville, SC 29620
Jerry D.
Job Details:
03/14/2024
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRV986FDEM01
Near Salem, SC 29676
Frank
Job Details:
03/14/2024
Freezer and top lights out.. replaced led light kit.. all lights working
We serviced a
KITCHENAID ICE MACHINE
Model KUIX535HPA01
Near Greer, SC 29650
Chris
Job Details:
03/14/2024
Unit has shorted drain pump. Ordeing for repair ; ordrng 1 W11539855 (Pump)
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Iva, SC 29655
Jerry D.
Job Details:
03/14/2024
"Water dripping into unit, also drain pump wont run, found wire harness broken , wires burnt. at tub, ordering, Q16; ordrng 1 W11101906 (Inlet valve) and 1 W10903238 (Harness) and 1 W11578565 (Cntrl) and 1 Q16 (Q16)"
We serviced a
KITCHEN AID OVEN
Model KEBS279BSS00
Near Greer, SC 29650
Chris
Job Details:
03/14/2024
Customer states unit has excessive preheat times . Customer also states unit loses a lot of heat when door is opened . Unit has multiple f6 faults stored. Temp sensors check good through live reading in diagnostics. All elements energize. Placed customers grill thermometer in oven along with weighted probe. Timed preheat. Unit hit target temps in 15 mins in each cavity. Customer insists unit will fault at certain points in cycles. Customers thermistor is 100 degrees off. Checked calibration. Calibration is already at max plus 30. Advised Customer if failure occurs unit will needs control for f6 faults . Controls are unavailable.
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Six Mile, SC 29682
Frank
Job Details:
03/14/2024
Loud grinding when spinning.. replaced gearcase and slider.. tested working ok; used 1 W11551646 (Spanner nut) from stock
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Simpsonville, SC 29681
Matt
Job Details:
03/14/2024
"Replaced agitator, gear case and screw. Ran an Entire rinse and spin cycle. All functions pass."
We serviced a
JENN-AIR ICE MACHINE
Model JUIFN15HX00
Near Seneca, SC 29672
Frank
Job Details:
03/14/2024
Thermistor reading 5kohms. New thermistor reading 4 kohms.. Replaced thermistor..not ordering control at this time.
We serviced a
MAYTAG WASHER
Model MVWB835DW1
Near Easley, SC 29642
Larry M.
Job Details:
03/14/2024
Gearcase seized. Will not separate from basket; ordrng 1 W10811960 (Basket) and 1 W11219115 (Outer tub)
We serviced a
KITCHEN AID RANGE
Model KSIB900ESS1
Near Easley, SC 29640
Larry M.
Job Details:
03/14/2024
"Found control non-responsive. Quoted customer book price of $1,231 for main control and control panel ; ordrng 1 L14jobcode (L14 job code) and 1 W11034444 (Control panel) and 1 W11100619 (Main control)"
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Greenville, SC 29617
Larry M.
Job Details:
03/14/2024
Installed timer. Ran test cycle. Checks ok
We serviced a
WHIRLPOOL M/W OTR
Model WMH32519HZ6
Near Greenville, SC 29605
Larry M.
Job Details:
03/14/2024
Found evidence of burn marks inside of unit. Found bottom interlock switch broken. Quoted customer bluebook quote of 263.15 to replace interlock switch ; ordrng 1 W11551761 (Switch) and 1 F12jobcode (F12 job code)
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ1
Near Greenville, SC 29605
Larry M.
Job Details:
03/14/2024
Found blockage in pump. Ordering pump and motor ; ordrng 1 W11416363 (Pump and motor)
We serviced a
WHIRLPOOL RANGE
Model WFE505W0HW5
Near Westminster, SC 29693
Frank
Job Details:
03/14/2024
Unit pulled out on arrival.. err was flashing replaced board tested working ok
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Clyde, NC 28721
Kari
Job Details:
03/14/2024
Installed parts unit checks ok
We serviced a
KITCHEN AID RANGE
Model KSGG700ESS2
Near Waynesville, NC 28785
Kari
Job Details:
03/14/2024
Installed parts. Unit checks ok collected balance of $253.12 and email receipt
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ00
Near Greer, SC 29651
Chris
Job Details:
03/14/2024
Unit has 5 broken wires in door. Unit needs new door. Gave customer a bluebook estimate for repair at 1838.05. Customer denied repair
We serviced a
AMANA DISHWASHER
Model ADB1400AMS1
Near Greer, SC 29651
Chris
Job Details:
03/14/2024
Customer has been told unit can be deemed unrepairable by customer service. Unit has shorted wash motor. Ordeing for repair ; ordrng 1 W11613566 (Control) and 1 W11613570 (Sump assembly)
We serviced a
MAYTAG WASHER
Model MVWB865GC0
Near Waynesville, NC 28785
Kari
Job Details:
03/14/2024
Installed parts unit checks ok customer paid balance by check $229.29
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAKZ2
Near Waynesville, NC 28785
Kari
Job Details:
03/14/2024
"Took quick pics, found unit leaking and tray full of water when I got there. No codes stored in unit. Found the black shield glided to tub cracked and coming off the bottom. Pulled unit half way out and ran it. Found it leaking from bottom seam on both sides. Need tub and third rack support for repair. ; ordrng 1 W11409866 (Tub) and 1 W11662340 (Left side third rack) and 1 N15 (Job code)"
We serviced a
MAYTAG DRYER
Model MED7230HW
Near Simpsonville, SC 29680
Matt
Job Details:
03/14/2024
Put unit through diagnostics test cycle and all functions pass. Customer was able to connect WiFi through the app. No error codes found.
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC503ESS00
Near Townville, SC 29689
Matt
Job Details:
03/14/2024
"Recovered refrigerant, replaced compressor, dye dryer and evaporator. Pulled a vacuum and weighed in 5.75 ounces of r 134a. Checks o.k"
We serviced a
MAYTAG REFRIGERATOR
Model MSS25N4MKZ04
Near Mills River, NC 28759
Brian
Job Details:
03/14/2024
"Unit in garage. Freezer is at zero when I arrived. Found unit had a good frost pattern and dampers and fans are working properly. Contacted tech support and spoke to Leon. He said unit is functioning as designed, and it isnt designed to function properly if ambient room temperature is below 55. Leon said the only unit that designed to work in a garage is the Gladiator model. At this time, unit is functioning as designed. Customer understood. Sr number (7738680391)"
We serviced a
WHIRLPOOL WASHER
Model WTW6157PB0
Near Greer, SC 29651
Chris
Job Details:
03/14/2024
Unit has no stored faults. Hooked water and power to machine. Ran quick wash cycle. No faults or leaks. Unit check is ok
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Inman, SC 29349
Chris
Job Details:
03/14/2024
"Customer states unit has long cycle times. Customer also states unit is louder than previous washer . Customer also states clean cycle ran for several hours, heavy duty cycle was almost 2 hours long. Unit has no stored faults . Unit passes automatic test mode. . Cold water fill is slow. Customer is on well. Cleaned cold water screen. Unit check is ok"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Anderson, SC 29621
Jerry D.
Job Details:
03/14/2024
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ2
Near Anderson, SC 29625
Jerry D.
Job Details:
03/14/2024
"Unit still dripping from vent, completed serv bulletin software update last time, double chkd software, chks ok, t line, johnathon, software ok, 00, recommend replacing vent ordering,j13; ordrng 1 W11527847 (Vent assy) and 1 W11184028 (Gasket) and 1 W11025634 (Bezel)"
We serviced a
WHIRLPOOL COOKTOP
Model WCG97US0HS00
Near Anderson, SC 29621
Jerry D.
Job Details:
03/14/2024
"Found regulator inoperable, installed regulator sent preid, flames now chks ok"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHS5
Near Gaffney, SC 29341
Sam
Job Details:
03/14/2024
Found unit making buzzing noise from inverter and leaking from inverter. Replaced pump and motor and control. Cycled unit through normal wash. No buzzing noise occurred. All components working. All functions pass.
We serviced a
WHIRLPOOL DRYER
Model WED5100HW2
Near Chesnee, SC 29323
Sam
Job Details:
03/14/2024
Cycled unit found. Motor cuts off after some time of running. Replaced motor and blower wheel. Cycled unit through timed dry. Unit no longer cutting off anymore. All functions pass.
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Boiling Springs, SC 29316
Sam
Job Details:
03/14/2024
Checked wiring at control board before replacing parts found loose connection at control board for incoming power. Fixed loose connection. Unit now turns on. Cycled unit through quick wash. All components working. all functions pass.
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Boiling Springs, SC 29316
Sam
Job Details:
03/14/2024
Installed control. Ran through quick wash. Customer still not happy with amount of water filling into tub during quick wash and normal cycles. Called techline went over tests and checks of pressure tube and pressure dome. Also ran unit through quick and normal wash cycles. Techline advised that levels of water in cycles are working as designed. All functions pass.File number # 7738573145
We serviced a
WHIRLPOOL RANGE
Model WFG505M0BS4
Near Boiling Springs, SC 29316
Sam
Job Details:
03/14/2024
Found units knobs cracked. Will order knobs and return with knobs for repair.; ordrng 5 WPW10339442 (Knobs)s
We serviced a
MAYTAG DRYER
Model MED5030MW0
Near Simpsonville, SC 29680
Jerry D.
Job Details:
03/14/2024
"Installed listed parts cycled unit through test and getting a f1e1 code tech sheet says that is a heater or motor both ohm out ok, relay on Cntrl ok, volts and polarity good, tech l, richard , cycled unit through test and still f1e1, ohmed out circuits , he advised to replace harness and cntrl, also customer requests supervisor, ordering, Q16; ordrng 1 8577274 (Thermistor) and 1 Q16 (Q16) and 1 W11625654 (Cntrl) and 1 W11437791 (Harness)"
We serviced a
AMANA DRYER
Model NED4655EW1
Near Piedmont, SC 29673
Jerry D.
Job Details:
03/14/2024
"Thermostat inoperable, installed thermal sent preid cycled unit through test and unit checks ok"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFC704FSS03
Near Hendersonville, NC 28739
Brian
Job Details:
03/14/2024
Found freezer door handle loose and also right fresh food door gasket torn. Tightened handle. New gasket (W10917313); ordrng 1 W10917313 (Gasket) and 1 J13 (Job code)