We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Belton, SC 29627
Jerry D.
Job Details:
03/22/2024
"Nut came loose, Belt and splutch torn up, installed parts sent preid, cycled unit through test and all functions are working properly"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Fountain Inn, SC 29644
Carl
Job Details:
03/22/2024
Installed new harness and pump cycled through a test cycle to ck operation unit ck ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDhZ00
Near Liberty, SC 29657
Frank
Job Details:
03/22/2024
Fc 5 degrees.. 40 in rc.. ice maker not cycling.. replaced ice maker now no water coming in. Replaced valve truck stock. tested working ok.. water filling ice maker cycling.. supply valve needs replacement.. talked with customer he is shutting water off and going to replace stem valve for water supply; used 1 WPW10179146 (Water valve) from stock
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW
Near Boiling Springs, SC 29316
Sam
Job Details:
03/22/2024
Installed all parts. Cycled unit through quick wash. Unit filled with water for about 10 minutes or less and continued cycle and finished normally. All components working all functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ06
Near Easley, SC 29642
Frank
Job Details:
03/22/2024
Thermistor coming apart from ice maker causing spuratic Operation. Replaced ice maker cycles ok...filled with water ok..
We serviced a
ELECTROLUX DRYER
Model EFME627UTT1
Near Chesnee, SC 29323
Sam
Job Details:
03/22/2024
"Found unit completely dead not doing anything. Found melted wires and control board on unit. Cant identify what caused melting of control and wire harness, could be other parts damaged or need of replacement because of control and harness melting. Will have to order multiple parts as worst case scenario.; ordrng 1 5304529782 (Motor) and 1 5304521447 (Knob assembly) and 1 5304521513 (Board assembly) and 1 5304533199 (Control) and 1 5304521235 (Harness) and 1 137032600 (Limiter) and 1 3204267 (Thermostat) and 1 Send2ndtech (Send 2nd tech) and 1 X20jobcode (X20 jobcode)"
We serviced a
WHIRLPOOL M/W OTR
Model WMH32519HZ10
Near Chesnee, SC 29323
Sam
Job Details:
03/22/2024
Installed all parts. Cycled unit through 2 minutes of heating unit sounds good. Unit heats all functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ03
Near Spartanburg, SC 29303
Matt
Job Details:
03/22/2024
Evacuated system. Replaced compressor and drier filter. Pressure tested unit. Unit held pressure. Pulled a vacuum and weighed in charge of r600a. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Spartanburg, SC 29307
Matt
Job Details:
03/22/2024
Unit was powered off when i arrived. Customer turned on circuit breaker and powered on unit. Compressor would not start. It tried multiple times and starter was making a smell. Replaced starter and compressor started right up and unit is pulling 1 amp and starting to cool. Called safety team with findings spoke to Alicia. She documented the file. file number 7738698136; used 1 W11615506 (Starter) from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRB322DMBM03
Near Cowpens, SC 29330
Matt
Job Details:
03/22/2024
"Replaced fan motor, blade, bracket and housing. Checks o.k"
We serviced a
WHIRLPOOL DRYER
Model WED8127LW2
Near Boiling Springs, SC 29316
Matt
Job Details:
03/22/2024
Customer stated dryer will run for 5 minutes and then shows done. Customer said this happens randomly and repeatedly even on timed dry. Customer wants unit replaced. Load in dryer was dry when I arrived. I put unit in diagnostics and found no listed fault codes. All sensor pass in diagnostics. Ran timed cycle for 15 minutes.Called tech line and spoke to Butch. Machine is working as designed. File number 7738189869 Customer can call customer care 1-800-253-1301
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ0B
Near Pickens, SC 29671
Frank
Job Details:
03/22/2024
Valve working.. water line froze.. defrosted tested working ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW02
Near Pickens, SC 29671
Frank
Job Details:
03/22/2024
air getting through seal clogged up EVAP clogged up opening from fc to rc.. cabinet coming apart. Called Techline.. sending for review. 7738736653 Sr number
We serviced a
MAYTAG DRYER
Model MEDB835DC4
Near Greenville, SC 29605
Larry M.
Job Details:
03/22/2024
"Replaced idler pulley, found rollers making noise. Ordering rollers; ordrng 4 WPW10314173 (Rollers)s"
We serviced a
WHIRLPOOL DRYER
Model WED6200SW1
Near Greer, SC 29650
Chris
Job Details:
03/22/2024
Unit has f1 fault and noise from blower. Parts are unavailable. Called 3rd party team . Unit unrepairable. File number for call is 7738717619
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Greenville, SC 29615
Chris
Job Details:
03/22/2024
Installed new parts.
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Greer, SC 29651
Chris
Job Details:
03/22/2024
"Installed new parts, unit check is ok. New labor authorization is m1aq2y0nl2"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Greer, SC 29651
Chris
Job Details:
03/22/2024
Unit has noisy damper. Ordeing for repair ; ordrng 1 W11236851 (Damper)
We serviced a
WHIRLPOOL WASHER
Model WTW4655JW2
Near Asheville, NC 28803
Kari
Job Details:
03/22/2024
"Took quick pics, found unit not moving past spin, ran through diagnostics found it makes a terrible noise when it switches to spin, took sound shield off and found the cam teeth obliterated. It looks like this is one of the cams that was misprinted. Installed new cam and belt. Ran diagnostic test again all functions check ok; used 1 W10721967 (Cam), and 1 WPW10006384 (Belt) from stock"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Biltmore Forest, NC 28803
Kari
Job Details:
03/22/2024
"Took quick pics, found unit shoiwng 8-3 hazardous water and unit constantly drips into basket and pump runs. Installed new valve. Ran diagnostic test unit checks ok; used 1 W11210459 (Valve) from stock"
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Asheville, NC 28805
Kari
Job Details:
03/22/2024
"Took quick pics, found unit showing 6-3, 0-5, 7-4,7-6,7-7, found. Rotor falling off and gearcase leaking. Also found the clutch just clicks and wont engage the basket. Also found 6-3 code repeats every time they are cleared need control gearcase and clutch for repair. ; ordrng 1 W11449841 (Gearcase) and 1 W10754448 (Clutch) and 1 W10734521 (Slide) and 1 W11624943 (Control) and 1 N15 (Job code)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Easley, SC 29642
Larry M.
Job Details:
03/22/2024
Found drain dump seeping. Changed seal on drain pump and ran test cycle. Checks o.k
We serviced a
JENN-AIR WALL OVEN
Model JJW2827IL01
Near Easley, SC 29642
Larry M.
Job Details:
03/22/2024
Replaced Console. Ran test cycle. Checks o.k
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS3
Near Greer, SC 29651
Chris
Job Details:
03/22/2024
Installed new parts. Unit check is ok.
We serviced a
MAYTAG RANGE
Model MER7700LZ2
Near Greer, SC 29651
Chris
Job Details:
03/22/2024
Installed new parts. Unit check is ok
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS1
Near Taylors, SC 29687
Chris
Job Details:
03/22/2024
Installed new parts unit check is ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ1
Near Old Fort, NC 28762
Kari
Job Details:
03/22/2024
"Took quick pic, found unit showing 1-1 codes. Cleared code. Ran diagnostic cycle. Unit now shows 9-2 code. Need parts for repair. Prescheduled for 4/5 PM; ordrng 1 W11412291 (Drain pump) and 1 W11672039 (Control) and 1 N15 (Job code)"
We serviced a
WHIRLPOOL WASHER
Model WTW6157PB0
Near Pelzer, SC 29669
Jerry D.
Job Details:
03/22/2024
"Water valve noisey and not working properly, installed valve cycled unit through test and no leaks found unit checks ok"
We serviced a
WHIRLPOOL DRYER
Model WED5605MC0
Near Piedmont, SC 29673
Jerry D.
Job Details:
03/22/2024
All functions are working properly at this time
We serviced a
WHIRLPOOL WASHER
Model WTW7500GC2
Near Piedmont, SC 29673
Jerry D.
Job Details:
03/22/2024
"In test f2e1 code, ordering, j13; ordrng 1 W11043822 (Console chrome)"
We serviced a
KITCHENAID DISHWASHER
Model KDFM404KPS2
Near Simpsonville, SC 29680
Jerry D.
Job Details:
03/22/2024
"Scratch and dent unit, unit inoperable, tub smashed door panel smashed and leaking water onto Cntrl, also unit was dropped and motor is smashed and leaking, X20; ordrng 1 X20 (X20) and 1 W11536143 (Heater) and 1 W11165093 (Cover) and 1 W11120458 (Tub assy) and 1 W11524493 (Cntrl) and 1 W11591421 (Console) and 4 W10348409 (Screw)s and 1 W11098822 (Inner door) and 1 W11265187 (Seal) and 1 W11554522 (Panel ss) and 1 W11416362 (Pump motor)"
We serviced a
KITCHEN AID DISHWASHER
Model KDFE104DBL2
Near Simpsonville, SC 29681
Jerry D.
Job Details:
03/22/2024
Installed listed parts cycled unit through test and no leaks found unit checks ok
We serviced a
ELECTROLUX WASHER
Model ELFW7637BT
Near Simpsonville, SC 29681
Carl
Job Details:
03/22/2024
Dispenser leaking j13; ordrng 1 5304514794 (Convayor) and 1 5304514792 (Disperser lower) and 1 J13 (Labor)
We serviced a
KITCHEN AID RANGE
Model KSDB900ESS0
Near Simpsonville, SC 29681
Carl
Job Details:
03/22/2024
Installed new part still same issue when cook top is used called tech line ran diagnostics it is a short in cook top harness ohm all ignitersck good soark module is not shorted to the chassis call jerry he said the unit has an issue theat we canot fix refund less the s/c
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW1
Near Six Mile, SC 29682
Frank
Job Details:
03/22/2024
Not spinning out clothes.. No errors present.. on quick wash skips rinse and spin goes to done. All functions working ok.. ; ordrng 1 W11680389 (Control board) and 1 W11591400 (Console) and 1 Jobcodel14 (Job code l14)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ09
Near Six Mile, SC 29682
Frank
Job Details:
03/22/2024
Need rails for pan.. didn't come with rails.. ; ordrng 2 W11226546 (Rails)s and 1 WPW10396909 (Front deli pan)
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Spartanburg, SC 29301
Sam
Job Details:
03/21/2024
Found unit making banging noise. Found no error codes in diagnostics. Found units feet not leveled causing the banging noise. Leveled feet of unit. Cycled unit through drain and spin. All components working. All functions pass.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS09
Near Six Mile, SC 29682
Frank
Job Details:
03/21/2024
Found damper rattling ordering to replace.. tab broken off water filter housing.. ordering to replace..; ordrng 1 WPW10594329 (Damper control) and 1 WP67001668 (Plate for filter) and 1 Jobcodel14 (Job code l14)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHV00
Near Greer, SC 29650
Chris
Job Details:
03/21/2024
"Customer states unit was making an extremely loud noise from rear if unit and food was warming up in both sections, unit has f1 fault in test 56. F1 indicates unit warmed up at one point and freezer temp wasnt satisfied to make ice. Customer unplugged unit from sunday to Tuesday and unit has worked since. Test 6 shows bi metal is good. Customer states there was no water behind unit or water on floor after unplugging unit indicating there was no defrost failure. Both ice makers are making ice and temperatures in both compartments are satisfied at 1 degree and 39 degrees via diagnostics. Test 3 and 4 functions as designed. Condenser fan,air baffle and compressor all show normal . No warmth on mullions indicating condenser fan is doing its job. Advised customer in hesitations for sealed system repair until we know for certain sealed system service is needed. Making svc fee good for 30 days for customer at no charge of customer returns call for service for within 30 day period."
We serviced a
MAYTAG DRYER
Model MED6500MBK0
Near Piedmont, SC 29673
Larry M.
Job Details:
03/21/2024
Found terminal lose found hotwire burnt found a hole in rear sheild; ordrng 1 W11591405 (Harness) and 1 W11627521 (Control) and 1 W11633114 (ACU control) and 1 279393 (Screws) and 1 279318 (Terminal)
We serviced a
WHIRLPOOL RANGE
Model WFG550S0LZ4
Near Greenville, SC 29605
Larry M.
Job Details:
03/21/2024
Replaced main control. Ran test bake cycle. Checks o.k
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Moore, SC 29369
Sam
Job Details:
03/21/2024
Found agitator fallen apart and in pieces. Upon further inspection units agitator and gear case shaft are stripped will order parts.; ordrng 1 W10772621 (Screw) and 1 WP3951744 (Agitator) and 1 W11454741 (Gearcase) and 1 Customerwouldliketopreschedule (Customer would like to preschedule)
We serviced a
AMANA DISHWASHER
Model ADB1400AMB1
Near Travelers Rest, SC 29690
Larry M.
Job Details:
03/21/2024
Replaced drain hose and ran test cycle. Checks ok.
We serviced a
MAYTAG RANGE
Model MER8800FZ1
Near Travelers Rest, SC 29690
Larry M.
Job Details:
03/21/2024
Found heating element broken. Quoted customer bluebook quote of $317.00. Customer approved job. Replaced element and ran test bake cycle. Checks o.k; ordrng 1 F12Jobcode (F12 Job code)
We serviced a
WHIRLPOOL COOKTOP
Model WCG97US0HS00
Near Anderson, SC 29621
Jerry D.
Job Details:
03/21/2024
"Customer says all burner flames are to low, already replaced regulator, gas pressure good for natural gas, customer says unexceptable, ordering, j13; ordrng 1 W10594395 (Assembly pipe) and 2 W10151347 (Orfice)s and 1 W10652711 (Orfice) and 1 W10672111 (Orfice) and 1 W10151362 (Orfice)"
We serviced a
WHIRLPOOL DRYER
Model WED5010LW1
Near Spartanburg, SC 29303
Sam
Job Details:
03/21/2024
"Installed control, harness, and motor. Cycled unit through timed dry. Unit now heats. All functions pass."
We serviced a
WHIRLPOOL DRYER
Model WED5605MC0
Near Greenville, SC 29617
Larry M.
Job Details:
03/21/2024
Found blower wheel bent. Found rollers and belt with evidence of warping. Ordering those parts. ; ordrng 1 W10508188 (Drum) and 4 WPW10314173 (Rollers)s and 1 661570V (Belt)
We serviced a
MAYTAG REFRIGERATOR
Model MSS25N4MKZ
Near Simpsonville, SC 29681
Carl
Job Details:
03/21/2024
Ck freezer temperature 4? on top shelf and unit is in the garage adjusted to a lower temp and advised customer unit ck ok
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF507HPS
Near Simpsonville, SC 29681
Carl
Job Details:
03/21/2024
Reinstalled filter cycled dispenser several times to ck operation unit ck ok
We serviced a
WHIRLPOOL DRYER
Model WED8127LW1
Near Simpsonville, SC 29681
Carl
Job Details:
03/21/2024
Randiagnostics took unit apart to inspect could not find any evidence of unit shorting or grounding out or even Lint burning reassembled unit cycle checks okay
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKV2
Near Asheville, NC 28803
Brian
Job Details:
03/21/2024
"Found f8e4 (float switch open) error code. Tested unit in diagnostics without adding detergent and found excess suds again. Cleared suds and tested unit multiple times and found suds gone and unit working properly with no leaks or any other issues.customer is using Laura Lynn dishwasher gel. I recommended customer not use gel anymore and try finish pods. Customer understood. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ2
Near Spartanburg, SC 29303
Sam
Job Details:
03/21/2024
Installed both parts. Cycled unit through quick wash. All components working. all functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model ED2KHAXVQ01
Near Spartanburg, SC 29307
Matt
Job Details:
03/21/2024
Customer stated unit doors cooling and warms up then starts back up and cools down. Evaporator fan running and condenser fan running. Fresh food temperature is 40 and freezer is -1. Put unit in diagnostics to run defrost unit pulls 571 Watts in defrost. Unit pulling 156 run Watts. Suspect cold control intermittently failing. Gave customer blue book estimate to replace cold control 401.00 total repair. Customer paying half today 200.50 and the other half 200.50 when part is installed ; ordrng 1 WP2315562 (Control) and 1 J13jobcode (J13 job code) and 1 Pleasepreschedule (Please pre schedule)
We serviced a
WHIRLPOOL RANGE
Model WFE525S0JS4
Near Anderson, SC 29626
Jerry D.
Job Details:
03/21/2024
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ06
Near Spartanburg, SC 29301
Sam
Job Details:
03/21/2024
Installed switch. Light in freezer now comes on. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ15
Near Gaffney, SC 29341
Sam
Job Details:
03/21/2024
Installed all parts. Cycled units ice maker and dispenser for ice. All components working all functions pass.
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Anderson, SC 29626
Jerry D.
Job Details:
03/21/2024
"F2 code no communication , ordering, j13; ordrng 1 W11130429 (Fascia) and 1 W11553798 (Cntrl)"
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Donalds, SC 29638
Jerry D.
Job Details:
03/21/2024
"Belt and idler broken, installed kit sent preid, cycled unit through test and unit checks ok"
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Hodges, SC 29653
Jerry D.
Job Details:
03/21/2024
"Unit inoperable, Console peeling loose, cntrls wet, ordering, j13; ordrng 1 W11524471 (Cntrl) and 1 W11496608 (Console)"
We serviced a
WHIRLPOOL RANGE
Model WFG505M0BS3
Near Greenwood, SC 29649
Jerry D.
Job Details:
03/21/2024
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT313CZLB00
Near Greenwood, SC 29646
Jerry D.
Job Details:
03/21/2024
"Temps 42 @ 16, Installed listed parts cleared drain and ice, sealed all around cabinet and liner, and sealed drain tube at compressor Per tech line johnathon, customer very upset she will monitor unit"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Greenwood, SC 29649
Jerry D.
Job Details:
03/21/2024
"Customer fixed leaking supply hose, unit not running,, in test no codes, cntrl puts water in then actuator keeps running, then cntrl goes blank, installed actuator from truck stock, still the same , cntrl gets to motor function and cntrl goes blank, have to reset to get it on, found wire harness broken , capacitor leaking , motor ohms are out of range, and motor hot, ordering Q16; ordrng 1 W10866238 (Capacitor) and 1 W10623547 (Motor) and 1 W10903238 (Harness) and 1 W11578565 (Cntrl)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Greenville, SC 29605
Matt
Job Details:
03/21/2024
"Thawed out frozen evaporator installed new main control and harness, checks o.k"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Slater-Marietta, SC 29661
Matt
Job Details:
03/21/2024
Customer stated lower ice maker stopped working a week ago. Upper ice maker is working fine. Found no ice in the ice maker. 3 degree freezer temperature. Ice maker just continuously rotates. Will order new ice maker.; ordrng 1 W11578780 (Ice maker freezer) and 1 Anytech (Any tech) and 1 J13jobcode (J13 job code)
We serviced a
MAYTAG WASHER
Model MVW6230HW2
Near Lake Lure, NC 28746
Brian
Job Details:
03/21/2024
"Inspected unit all over and found no visible damage or holes. Tested unit in normal cycle, automatic and manual diagnostics, multiple times, while inspected all hoses and connections and every other part of unit. At this time, I can find no leaks coming from washer."
We serviced a
AMANA REFRIGERATOR
Model ART308FFDM10
Near Flat Rock, NC 28731
Brian
Job Details:
03/21/2024
"Found ice maker turned off when I arrived.tested ice maker and found it leaking from the fill line, into the valve. Adjusted and found fill line not pushed in all the way. Corrected and tested ice maker multiple times and found leak no longer present. At this time, all operations ok with no leaks detected."
We serviced a
JENN-AIR REFRIGERATOR
Model JFFCC72EFS00
Near Hendersonville, NC 28739
Brian
Job Details:
03/21/2024
Found top right door cover and components damaged. Also found both fresh food door gaskets torn. Harness (W10784245) cover (W11204565) switch (W11171663) and 2 gaskets (W10917313) needed.; ordrng 1 W10784245 (Harness) and 1 W11204565 (Cover) and 1 W11171663 (Switch) and 2 W10917313 (Gasket)s and 1 L14 (Job code)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRR56X18FW03
Near Slater-Marietta, SC 29661
Matt
Job Details:
03/21/2024
"Recovered refrigerant. Replaced control, compressor, drier filter and evaporator. Pulled a vacuum and then weighed in 4.8 ounces of 134a. Evaporator has a full even frost pattern. All functions pass."
We serviced a
MAYTAG DRYER
Model MED7230HC1
Near Etowah, NC 28729
Brian
Job Details:
03/21/2024
Installed new motor belt switch and blower wheel. Tested and found all operations ok at this time. Collected 321.95
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Mills River, NC 28759
Brian
Job Details:
03/21/2024
"Found F7e5 (motor fault). Tested unit in diagnostics cycle and found belt squealing during spin cycle. Replaced Belt (W11239857) and calibrated unit. Tested and found al operations ok at this time. Reviewed two step start behavior with unit. Customer understood. At this time, all operations ok with no leaks detected. ; ordrng 1 W11239857 (Belt TS)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHV06
Near West Union, SC 29696
Frank
Job Details:
03/21/2024
Compressor buzzing trying to start.. ordering compressor and starter would try first.. part and labor covered under warranty. Paid TC $150.. ; ordrng 1 W11557425 (Compressor) and 1 W11504416 (28a) and 1 W11504431 (28b) and 1 W11506621 (28c) and 1 W11506635 (28d) and 1 w11506635 (Access port) and 1 wpw10143759 (Dryer) and 1 R600a (R600a) and 1 Sealedsystemtech (Sealed system tech) and 1 Sendfcwithmatraining (Send fc with ma training)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM08
Near Salem, SC 29676
Frank
Job Details:
03/21/2024
Replaced motor.. needs another ice door ordered wrong color. Put in bisc ice door ice now dispensing.. need to get new ice door.; ordrng 1 W11678839 (Ice door)
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Simpsonville, SC 29681
Carl
Job Details:
03/21/2024
Found shaft of float damaged and melted woll order k13; ordrng 1 Wpw10316267 (Over fill stanpipe) and 1 Wpw10346525 (Float) and 1 J13 (Labor)
We serviced a
JENN AIR RANGE
Model JDRP548WP03
Near Reidville, SC 29375
Carl
Job Details:
03/21/2024
Found low voltage to the ui. J13 1910.10 collected ; ordrng 1 Wpw10464534 (Interface) and 1 Wpw10145531 (Power supply) and 1 J13 (Labor)
We serviced a
KITCHEN AID RANGE
Model KDRS467VSS03
Near Inman, SC 29349
Chris
Job Details:
03/21/2024
Installed new glass. Unit check is ok
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS0
Near Inman, SC 29349
Chris
Job Details:
03/21/2024
Customer states unit has burning smell and shuts down . Unit has 7-1 and 9-1 faults . Unit has wash motor failure .Gave customer a bluebook estimate for repair at $799.92.customer denied repair.
We serviced a
AMANA DRYER
Model NED4655EW1
Near Salem, SC 29676
Frank
Job Details:
03/21/2024
Checked voltage. Only 50v coming in on L2. Reset breaker tested working ok. Getting 240v to unit now..
We serviced a
MAYTAG REFRIGERATOR
Model MFX2570AEM4
Near Salem, SC 29676
Frank
Job Details:
03/21/2024
Replaced ice maker assembly and harness.. tested cycles ok and fills with water ok.
We serviced a
AMANA DRYER
Model NED4655EW1
Near Waynesville, NC 28785
Kari
Job Details:
03/21/2024
"Took quick pics, found belt broken and debris in blower housing cleared debris and replaced dryer kit. Unit checks ok"
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Waynesville, NC 28786
Kari
Job Details:
03/21/2024
"Took quick pics, found unit showing F0E9 off balance pause. Found unit moving all over and the suspension is bouncing more than it should. Also found unit louder than it should be in agitation and spin. Need parts for repair, prescheduled customer for 4/9 AM ; ordrng 1 W11449840 (Gearcase) and 1 W10721967 (Cam) and 1 W11130362 (Suspension) and 1 N15 (Jobcode)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDW10
Near Waynesville, NC 28786
Kari
Job Details:
03/21/2024
"Took quick pics, found unit FF temp 37.73 degrees and freezer at 15.2. Removed back evap cover and found units frost pattern normal found defrost thermistor 8.6 k ohms and 5dcv from control. Found defrost heater with 120v and getting hot. Turned control up and found fan is running normally and has 120v to it. Called techline spoke with Chris 7738728834 at techline and reported my findings, he said the fz doesnt have an ambient thermistor and runs off the cooling of the fridge. Turned freezer dial to max to cut off air to ff to help with freezing. Also explained something with higher water content like eggs, veggies, etc, will freeze on the upper shelf. Also recommended turning control dial down a snowflake if its still too cold on upper shelf. Corrected fill tubing into icemaker so water will stop flooding the freezer floor. Reported findings to Trade care 7738687653 unit is functioning as designed"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Clyde, NC 28721
Kari
Job Details:
03/21/2024
Installed parts unit checks ok
We serviced a
WHIRLPOOL DRYER
Model WED560LHW2
Near Canton, NC 28716
Kari
Job Details:
03/21/2024
Installed parts unit checks ok
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS2
Near Fair Play, SC 29643
Frank
Job Details:
03/20/2024
Tested unit no leaking found gasket ok.. leveled legs brought front of machine up.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Tryon, NC 28782
Brian
Job Details:
03/20/2024
"Found unit cycling as if it had been unplugged and plugged back in. In diagnostics I tested all components as was unable to recreate issue that way. I recommended customer try to get a recording of the heat beat noise, if it happens again.Control (W11224256) and ui (W11636544) needed for power issue. ; ordrng 1 W11224256 (Control) and 1 W11636544 (Ui) and 1 L14 (Job code)"
We serviced a
WHIRLPOOL COOKTOP
Model WFE320M0JS4
Near Hendersonville, NC 28791
Brian
Job Details:
03/20/2024
Found cooktop cracked. All other functions ok at this time. New cooktop (W11178791) needed; ordrng 1 W11178791 (Cooktop) and 1 J13 (Job code)
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Hendersonville, NC 28791
Brian
Job Details:
03/20/2024
"Found no saved error codes. Ran unit through auto diagnostics and found unit completing without issues. At this time, unit Is functioning as designed. Reminded customer of the importance of proper loading procedures and appropriate cycle selection for load in unit. Customer understood. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
JENN-AIR ICE MACHINE
Model JIM158XYRS1
Near Seneca, SC 29672
Frank
Job Details:
03/20/2024
Recirculating pump loud making noise. In diag drain motor not coming on.. not letting water in getting 120v to valve.. checked water is on ok..; ordrng 1 W11542867 (Recirculating pump) and 1 W11542868 (Drain pump) and 1 W10897719 (Valve) and 1 Jobcodel14 (Job code l14)
We serviced a
WHIRLPOOL M/W OTR
Model WMH32519HZ07
Near Greenville, SC 29615
Larry M.
Job Details:
03/20/2024
Tested fan. Checks o.k. Checked power. Checks o.k Recommend second man; ordrng 1 2manjobcode
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS06
Near Taylors, SC 29687
Larry M.
Job Details:
03/20/2024
"Replaced main control, ui, and panel ui. Checks ok"
We serviced a
WHIRLPOOL RANGE
Model WOD51EC0HS
Near Greenville, SC 29605
Larry M.
Job Details:
03/20/2024
Found UI not responding to touch accurately. Time advancing ordering console.; ordrng 1 W11297709 (UI Console)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ02
Near Powdersville, SC 29642
Larry M.
Job Details:
03/20/2024
Found unit pulled out in middle of kitchen when I arrived. Found compressor making noise. Quoted customer a compressor and dryer filter with bluebook quote of $1117.45. ; ordrng 1 W19jobcode (W19 Job code) and 1 WPW10466675 (Compressor)
We serviced a
MAYTAG WASHER
Model MHW5500FW0
Near Fletcher, NC 28732
Brian
Job Details:
03/20/2024
"Found door locked and unit unplugged when I arrived. After supplying power to unit, drain pump came on. Let drain pump time out. Found F3e1 (pressure switch error) F5e2 (door lock error) F9e1 (long drain) F8e3 (overflow condition) error codes. Cleared codes and ran unit through diagnostics cycle and found unit completing without issues. Customer said when this has happened on the past, they would unplug he unit for a while and then plug it in and it would work. If issue happens again, Control (W11201285) will be needed. Quoted customer 664.32 to complete repairs. Customer did not wish to proceed with repairs at this time. Contacted Saftey team and spoke to Lisa. Documented findings with her. Sr number (7738695769)."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Roebuck, SC 29376
Sam
Job Details:
03/20/2024
Installed all parts. Cycled unit through quick wash. All components working. Unit progressing through cycle. All functions pass.
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKB0
Near Seneca, SC 29672
Frank
Job Details:
03/20/2024
Only code is f9e1. Tested drain pump.. seems over heating shutting off. Replaced drain pump tested working ok not leaking.. sump motor seems to be running ok no issues
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ07
Near Fountain Inn, SC 29644
Carl
Job Details:
03/20/2024
Eran sr 7738722882 tech line advise is for customer not to use ice for at least 24 hr customer will call me in a couple of days so i can stop by and take pics temp in freezer are 3 ? ; O-emld tckt
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Fountain Inn, SC 29644
Carl
Job Details:
03/20/2024
Installed new bulkhead and drum cycled unit to ck operation unit ck ok
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Simpsonville, SC 29680
Jerry D.
Job Details:
03/20/2024
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Burnsville, NC 28714
Kari
Job Details:
03/20/2024
"Took quick pics, found unit showing 7-1 code, ran unit through diagnostics found the agitator and tub wont spin, found it only hums, found capacitor showing OL. Installed new capacitor ran diagnostic test and drain and spin, unit checks ok."
We serviced a
WHIRLPOOL DISHWASHER
Model MDB4949SDM0
Near Six Mile, SC 29682
Frank
Job Details:
03/20/2024
Needs valve not letting water in. Declining repair.. quoted $348.40. Paying trip 125$. Cash