"Found unit unlevel, leveled unit amd cycled unit through test and unit checks ok"

Unit has frozen water tank. Tank has been insulated with foam . Temps are 38 in fresh food. Called tech line and spoke with drew. Drew sent diagram and part number to replace. Ordeing parts for repair . File number 7739773367; ordrng 3 W10684392 (Foam)s and 1 WPW10394053 (Housing) and 1 W11204869 (Tank) and 1 N15

Unit has worn suspension. Gave customer a bluebook estimate for repair at $527.25. Installed new parts. . Unit check is ok.

Replaced wire harness to sensor.. tested working ok

Unit has a variety of faults. Man fault is f70. Control has heartbeat symptoms. Door locked. Unit pulsates on and off. Unit needs control and possible further diagnoses . Gave customer a bluebook estimate for control at $727.50. Customer denied repair

Installed new panel . Unit check is ok

Verified power coming to unit. Attempted to put in diagnostics mode. Unit would not respond. Will order main control ; ordrng 1 W11627413 (Main control)

Found open in drain pump. Main would not go into diagnostics mode. Will need drain pump and main control again. ; ordrng 1 W11399437 (Drain pump)

"Found ice clunking up, will need flap and dispenser. ; ordrng 1 W11678832 (Ice door)"

Customer has unit disassembled upon arrival . Control clicks over and over but will not wake. Ordeing parts for repair . Customer to reassemble unit ; ordrng 1 W11543997 (Control) and 1 W11614635 (Filter) and 1 W11478519 (Panel)

Found ice building up around freezer fan. Steamed ice. Will need diffuser and fan harness ; ordrng 1 W11559968 (Fan) and 1 WP2169142 (Fan)

Installed new top. Powered on unit to make sure all functions work correctly. All functions pass.

Gasoline fitting seized up. Could not loosen. Will need gasline 30-48kitrc gas line. ; ordrng 1 30-48kitrc (Gas line)

"Complaint is that ice is wet and soupy throughout the day. I tested and found heater ok and bin thermistor ok. In diagnostic I found water reservoir not filling all the way. Compressor fan ok and good frost pattern. Replaced Circulation pump (W11542867) and tested again. Found all operations ok at this time, with no leaks detected. Did not move unit."

Installed new cap cycled unit to ck operation unit ck ok

Found belt off idler reinstalled cycled unit to ck operation unit ck ok

Found vent tube off blower reinstalled cycled unit ck ok

Found rt valve worn j13; ordrng 1 WPW10206288 (Rc valve)

Found units control acting erratic causing random flashing lights and starting cycles on its own. Will order control for repair.; ordrng 1 W11603811 (Control)

Found that when water is turned on unit leaks from behind unit. Found tube that connects to inlet hose and water filter housing with a hole causing it to leak when water is turned on. Will order tube for repair.; ordrng 1 W11162040 (Tube water)

"Found unit with blown thermostat, thermal cut off and heating element will order parts for repair.; ordrng 1 279838 (Element) and 1 279816 (Thermal cut off) and 1 WP8318268 (Thermostat)"

Found unit not able to start. Found door switch not activating. Checked connection of door switch found door switch not fully seated into connector. Reseated connection. Tested operation with timed dry for 10 minutes. Unit heats and tumbles. All functions pass.

"Cntrl not responding in regular cycle, in test. Getting a actuator code, ordering, j13; ordrng 1 W11398781 (Actuator) and 1 W11578565 (Cntrl)"

Installed listed parts cycled unit through test and unit checks ok

"Installed compressor and pulled vacuum. Found unit pressure rising during leak check, found the evaporator had a slight leak from back of coils, installed new evaporator. Pulled vacuum and leak checked unit pressure held and I filled unit with 1.48 oz of R600a evap now has frost pattern and condenser is getting hot. unit checks ok. W1C2GV0NL1.5 ; used 1 W11506635 (Coupler), and 1 W11394622 (Evap) from stock"

Test 56. E2 error.. imk not harvesting. Replaced imk tested working ok.. bb quoted $489.01.

Installed listed parts.. tested working ok

Installed listed parts cycled unit through test and all functions are working properly

Unit has leak from valve. Unit also has undisclosed leak from water line from under unit and drain tube will not seat into drain hole. No damage to drain tube itself. Drain collapsed in liner. Customer denied further repair

Unit has failed control. Ordering for repair ; ordrng 1 W11648349 (Control)

Found float stuck in closed position with no water in tray adjusted switch and cycled unit to ck operation unit ck ok

"Ice bucket broken, ordering, j13; ordrng 1 W10558423 (Bucket ice)"

"Installed new ice bucket and tested. Found all operations ok at this time,with no leaks detected. Did not move unit."

Found element open and thermal fuse open. Will order both ; ordrng 1 W10909685 (Cut off thermal) and 1 279973 (Fuse)

"Replaced control box, and thermistor. Insured correct temperature in both sections."

"Lock broken cntrl dead, volts and polarity good, ordering, j13; ordrng 1 W11491433 (Cntrl) and 1 W11403468 (Bezel) and 1 W11368616 (Latch)"

"Found unit unresponsive, volts and polarity good, installed cntrl sent preid, cycled unit through test and calibration all functions are working properly"

"Cycled unit through test and heater not getting hot, found right side heater not plugged in, plugged in connector, cycled unit through test and heater is pulling 6 amps"

"Wash Pump broken drain pump loud, cntrl not opening dispenser, ordering, j13; ordrng 1 W10537634 (Pump drain) and 1 W10837401 (Sump assy) and 1 W10834738 (Cntrl)"

"Customer concerned about ice clumping in ice bin and getting stuck, as well as some food freezing around ice maker housing. Tested and inspected and found all ice maker functions and all other functions operating as designed. I recommended customer dump ice bin out every month or so to remove any compacted ice fragments. Explained to customer that the cold air in the fresh food section comes from air vent in ice maker housing, and food directly beside or under ice housing may freeze. Recommended customer keep high moisture items away from this area. Customer understood. At this time, unit is functioning as designed with no leaks detected. Did not move unit."

Found unit not making ice. Found arm of ice maker frozen unable to cycle. Removed ice and cycled ice maker. Ice maker cycling properly now. All functions pass.

"Found unit with multiple problems and error codes. Unit will not drain, cycle will not start, units actuator will not activate and unit is making grinding noise when in spin. Found error codes f7e1, f9e1, f1e2 and f8e6. Unit will need multiple parts for repair. Will order parts and return at later date.; ordrng 1 W11513246 (Control) and 1 W11449840 (Gearcase) and 1 W11481722 (Actuator) and 1 W10721967 (Splutch) and 1 W11399437 (Drain pump) and 1 W11643701 (Wire harness) and 1 Preschedule (Preschedule)"

Found unit making loud knocking noise when in use. Slider not fully engaging or disengaging properly. Slider appears to be separating as well. Will order parts for repair.; ordrng 1 W10734521 (Slider) and 1 W10754448 (Clutch) and 1 W10915701 (Rotor)

Installed L.E.D light. Found short in harness. Could not find harness to order.

Found drain pump clogged. Will need 2 man job code. ; ordrng 1 2manjobcode (2 man job code)

Refrigerator temperature 37Freezer temperature 0Unit is functioning as designed. All functions pass.

New Tub damaged will order new; ordrng 1 W11219115 (Tub outter)

"Took quick pics, found unit doa and lid locked full of water. Found the control didnt have a status light, unit has 120v into board but no voltage to any of the outlets puts, found drain pump showing 19 ohms, tipped unit up and found rotor and underneath of machine covered in yellow gearcase oil. Made est for main control, gearcase and slide $1,082.03 customer declined and is going to buy a new unit. Had office run cc for $150 and had RH send receipt through the regular mail."

Found motor damaged installed new motor unit ck ok; used 1 279827 (Motor) from stock

"Right front burner switch stuck on, installed w10434452 from truck stock cycled unit through test and unit checks ok"

"Found fresh food and freezer ceiling leds out. Found service pointer regarding this issue. I recommended customer replace all unit led modules. Quoted customer 484.14 to install 3 led kits (W11632139). Customer wished to proceed. Instead all interior led modules and found all operations ok at this time, with no leaks detected. Did not move unit. Collected total."

Installed new switch and motor unit ck ok; used 1 W10117655 (Start switch) from stock

"Unit frosted over again, called tech line and spoke with Eric, Eric advised defrost heater should read higher ohms but not past 24ohms Eric suspects defrost heater is weak . Was advised to replace heater and harness. Harness retail is $70.54 and heater is $75.18 and c1 is 34.99 . ; ordrng 1 242044113 (Heater) and 1 241520403 (Harness)"

Unit has shorted wash motor. Installed new parts. Unit check is ok . No leaks

Unit has shorted wash motor . Ordeing for repair ; ordrng 1 W11613479 (Wash motor)

Customer states fire/spark shot out of rear on braided stainless water lines. Unit plugged in upon arrival . Unit passes automatic test mode . Customers outlet checks ok. Unit has arc mark on cold side water hose and rear panel . Called tech line and spoke with Chris . Unit has no stored faults .no voltage feel from unit to waterlines . No property damage or injury .sent pictures to Chris . Chris states cold water would have had to have voltage coming through cold water side. Unit passes all unit checks and works as designed. Unit has no voltage from ground to machine or ground to both water hoses . Chris advised to secure hoses to not touch machine . Chris advised we cant replicate failure at this time . File number for call is 7739743953.

Found unit with same issue of filling with water pausing for a few minutes and then draining. Unit also starting without money. Found error codes for long fill and no fill. Unit has water pressure of 100 psi and good voltage. Called techline. Techline advised to run unit through diagnostic cycle to verify components functions. All components working. Cleared error codes and cycled unit through calibration cycle. Unit appears to be operating normally again and requires money to start. No new error codes found in diagnostics. Cycled unit and problem still occurring. Will order parts.SR#7739627673; ordrng 1 W11126319 (Coin chute) and 1 W11205048 (Valve)

Found glass and handle broken totally..; ordrng 1 W11730234 (Handle) and 2 W10896982 (Screw)s and 1 W11707153 (Door glass) and 1 W11178521 (Name plate) and 1 Jobcodel14 (Job code l14)

Found ref shuting down from dc fall out Replaced ice box fan. Replaced damper and EVAP fan.. DC voltage components.. tested through diagnostics all working ok cooling ok..

"Took quick pics, found units hinges too tense and not letting door close all the way. Gave cust est of $469.93 for repair. Cust agreed and paid half $234.97 by cc office ran will owe $234.96 on completion Rescheduled for 8/27 PM ; ordrng 1 W11551369 (Hinge) and 1 W11551376 (Hinge) and 1 J13 (Job code) and 1 Partsinwarehouse"

Installed parts unit checks ok

Installed parts unit checks ok

Installed parts unit checks ok

"Travis @ techline 7739744458Took quick pics, found unit unplugged. Left unit unplugged and took evap panel off. Took quick pics, of all connections on harness, found all wires to be in perfect condition, no breaks or tears, or pinched and took pictures of heater and evap tray, entire tray is silver with no black marks or arch pitting. Found no fracturing in heater rod, heater showing 36 ohms no indication of arching or grounding. Pulled unit out and took off unit cover, took pictures of lower harness and drain tube extension. Found everything looks good and no broken wires or arch marks on anything. Reinstalled unit compartment cover and plugged unit in, found compressor runs normally and fans come on. Called techline spoke with Travis and he noted everything I relayed from the customer, he had me text him pictures of the evap fan harness and the heater and the evap tray. He attached those photos to the file and made documentation of it. He told me I can by pass bi metal since unit has been off and pour some water on the heater to check for arching. I did by pass bimetal, turned unit to test 6 and waited approximately 10 minutes for it to get hot and poured about 8oz of water over it. Heater made normal sizzling noise thats to be expected when water comes in contact with a hot heater rod. Found no indication of sparking or arching when hot heater was wet. Reinstalled bimetal and reassembled all parts and panels. Unit is functioning as manufacturer designed. Unit checks ok."

Found unit not cooling. Found temperature in refrigerator at 45 and freezer at 25. Checked amp draw at compressor and found .22 amp draw indicating leak in unit. Called techline. Went over checks with techline. Found unit has leak somewhere in system. Will order parts for repair. SR#7739750856; ordrng 1 W11546605 (Evaporator) and 1 W11708426 (Condenser) and 1 W11580057 (Compressor) and 1 W11109499 (Drier filter) and 1 R600 (R600) and 1 Nitrogen (Nitrogen) and 1 Sealedsystemtech (Sealed system tech) and 1 X20 (X20) and 1 Preschedule (Preschedule)

Found f4e4 (l2 line voltage error) f4e3 (restricted airflow). Tested unit and found it not heating. Checked and found element bad and wire going to element damaged and charred. Also found rollers not functioning properly. Main wire harness (W10901572) element (WP3387747) and roller kit (4392067) needed. Quoted customer 815.63 to complete repairs. Customer did not wish to proceed with repairs at this time. Collected 150 for service call. Left unit off at breaker.

"Temps 36@1 found interface panel buttons not working properly, unplugged unit, removed panel found wire connector loose, reattached all connections tight, plugged unit in, all functions are working properly"

Replaced parts listed.. tested working ok.. heater coming on and off ok..

Found unit still freezing items. Called techline. Techline went over checks for unit. Found that one wire to damper being able to open and close was backing out of connector causing it to not close and freezing all items. Fixed wire that was backing out of connector. Cycled units damper. Damper opening and closing properly. All functions pass. SR#7739748875

"Ice bucket broken, ordering, j13; ordrng 1 W10558423 (Bucket ice)"

"Installed new ice bucket and tested. Found all operations ok at this time,with no leaks detected. Did not move unit."

Found element open and thermal fuse open. Will order both ; ordrng 1 W10909685 (Cut off thermal) and 1 279973 (Fuse)

"Replaced control box, and thermistor. Insured correct temperature in both sections."

"Lock broken cntrl dead, volts and polarity good, ordering, j13; ordrng 1 W11491433 (Cntrl) and 1 W11403468 (Bezel) and 1 W11368616 (Latch)"

"Found unit unresponsive, volts and polarity good, installed cntrl sent preid, cycled unit through test and calibration all functions are working properly"

"Cycled unit through test and heater not getting hot, found right side heater not plugged in, plugged in connector, cycled unit through test and heater is pulling 6 amps"

"Wash Pump broken drain pump loud, cntrl not opening dispenser, ordering, j13; ordrng 1 W10537634 (Pump drain) and 1 W10837401 (Sump assy) and 1 W10834738 (Cntrl)"

"Customer concerned about ice clumping in ice bin and getting stuck, as well as some food freezing around ice maker housing. Tested and inspected and found all ice maker functions and all other functions operating as designed. I recommended customer dump ice bin out every month or so to remove any compacted ice fragments. Explained to customer that the cold air in the fresh food section comes from air vent in ice maker housing, and food directly beside or under ice housing may freeze. Recommended customer keep high moisture items away from this area. Customer understood. At this time, unit is functioning as designed with no leaks detected. Did not move unit."

Found unit not making ice. Found arm of ice maker frozen unable to cycle. Removed ice and cycled ice maker. Ice maker cycling properly now. All functions pass.

"Found unit with multiple problems and error codes. Unit will not drain, cycle will not start, units actuator will not activate and unit is making grinding noise when in spin. Found error codes f7e1, f9e1, f1e2 and f8e6. Unit will need multiple parts for repair. Will order parts and return at later date.; ordrng 1 W11513246 (Control) and 1 W11449840 (Gearcase) and 1 W11481722 (Actuator) and 1 W10721967 (Splutch) and 1 W11399437 (Drain pump) and 1 W11643701 (Wire harness) and 1 Preschedule (Preschedule)"

Found unit making loud knocking noise when in use. Slider not fully engaging or disengaging properly. Slider appears to be separating as well. Will order parts for repair.; ordrng 1 W10734521 (Slider) and 1 W10754448 (Clutch) and 1 W10915701 (Rotor)

Installed L.E.D light. Found short in harness. Could not find harness to order.

Found drain pump clogged. Will need 2 man job code. ; ordrng 1 2manjobcode (2 man job code)

Refrigerator temperature 37Freezer temperature 0Unit is functioning as designed. All functions pass.

New Tub damaged will order new; ordrng 1 W11219115 (Tub outter)

"Took quick pics, found unit doa and lid locked full of water. Found the control didnt have a status light, unit has 120v into board but no voltage to any of the outlets puts, found drain pump showing 19 ohms, tipped unit up and found rotor and underneath of machine covered in yellow gearcase oil. Made est for main control, gearcase and slide $1,082.03 customer declined and is going to buy a new unit. Had office run cc for $150 and had RH send receipt through the regular mail."

Found motor damaged installed new motor unit ck ok; used 1 279827 (Motor) from stock

"Right front burner switch stuck on, installed w10434452 from truck stock cycled unit through test and unit checks ok"

"Found fresh food and freezer ceiling leds out. Found service pointer regarding this issue. I recommended customer replace all unit led modules. Quoted customer 484.14 to install 3 led kits (W11632139). Customer wished to proceed. Instead all interior led modules and found all operations ok at this time, with no leaks detected. Did not move unit. Collected total."

Installed new switch and motor unit ck ok; used 1 W10117655 (Start switch) from stock

"Unit frosted over again, called tech line and spoke with Eric, Eric advised defrost heater should read higher ohms but not past 24ohms Eric suspects defrost heater is weak . Was advised to replace heater and harness. Harness retail is $70.54 and heater is $75.18 and c1 is 34.99 . ; ordrng 1 242044113 (Heater) and 1 241520403 (Harness)"

Unit has shorted wash motor. Installed new parts. Unit check is ok . No leaks

Unit has shorted wash motor . Ordeing for repair ; ordrng 1 W11613479 (Wash motor)

Customer states fire/spark shot out of rear on braided stainless water lines. Unit plugged in upon arrival . Unit passes automatic test mode . Customers outlet checks ok. Unit has arc mark on cold side water hose and rear panel . Called tech line and spoke with Chris . Unit has no stored faults .no voltage feel from unit to waterlines . No property damage or injury .sent pictures to Chris . Chris states cold water would have had to have voltage coming through cold water side. Unit passes all unit checks and works as designed. Unit has no voltage from ground to machine or ground to both water hoses . Chris advised to secure hoses to not touch machine . Chris advised we cant replicate failure at this time . File number for call is 7739743953.

Found unit with same issue of filling with water pausing for a few minutes and then draining. Unit also starting without money. Found error codes for long fill and no fill. Unit has water pressure of 100 psi and good voltage. Called techline. Techline advised to run unit through diagnostic cycle to verify components functions. All components working. Cleared error codes and cycled unit through calibration cycle. Unit appears to be operating normally again and requires money to start. No new error codes found in diagnostics. Cycled unit and problem still occurring. Will order parts.SR#7739627673; ordrng 1 W11126319 (Coin chute) and 1 W11205048 (Valve)

Found glass and handle broken totally..; ordrng 1 W11730234 (Handle) and 2 W10896982 (Screw)s and 1 W11707153 (Door glass) and 1 W11178521 (Name plate) and 1 Jobcodel14 (Job code l14)

Found ref shuting down from dc fall out Replaced ice box fan. Replaced damper and EVAP fan.. DC voltage components.. tested through diagnostics all working ok cooling ok..

"Took quick pics, found units hinges too tense and not letting door close all the way. Gave cust est of $469.93 for repair. Cust agreed and paid half $234.97 by cc office ran will owe $234.96 on completion Rescheduled for 8/27 PM ; ordrng 1 W11551369 (Hinge) and 1 W11551376 (Hinge) and 1 J13 (Job code) and 1 Partsinwarehouse"

Installed parts unit checks ok

Installed parts unit checks ok