We serviced a
KITCHEN AID WALL OVEN
Model KOSE500ESS01
Near Greenville, SC 29607
Nathan
Job Details:
05/09/2025
After replacing thermal fuse I went to test the ovens and they both dont turn on the bake function. Needs thermal fuses. Quoted $334.64 to replace both thermal fuses plus $311.44 totaling $646.08 with check number 1777. Total paid to fix both ovens is $957.52. Pre-heated both ovens to 350 degrees to confirm operation. Paid remaining balance for both ovens $646.08. Office will send receipt after check clears. Thank you. ; ordrng 1 WP4449751 (Thermal fuse (job complete))
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPM2
Near Union, SC 29379
Sam
Job Details:
05/09/2025
Installed new pump and motor. Cycled through diagnostics cycle. All components activating. No leaks during cycle. All functions pass.
We serviced a
WHIRLPOOL KITCHEN
Model WFG320M0MS0
Near Roebuck, SC 29376
Sam
Job Details:
05/09/2025
Found units outer glass of door fallen out of position in bottom portion. Brackets holding glass came loose and caused glass to pop out of place. Adjusted brackets. Tightened brackets with bigger screws. Units glass staying secure and brackets not loosening. All functions pass.
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Roebuck, SC 29376
Sam
Job Details:
05/09/2025
Found unit will constantly cycle in spin will start to spin then stop at beginning of spin and start sensing again. Unit repeats process endlessly until popping up with out of balance error code. Checked spin with load. Unit spins fine and within normal vibration guidelines. Checked error codes. No error codes. Unit needs control for repair.; ordrng 1 W11624938 (Control) and 1 N15 (N15)
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Greenville, SC 29615
Larry M.
Job Details:
05/09/2025
Found unit smoking from drain pump and harness. Called safety SR:7741539808
We serviced a
WHIRLPOOL ICE MACHINE
Model KUIX335HPS00
Near Taylors, SC 29687
Matt
Job Details:
05/09/2025
Found compressor started has failed. Replaced starter and watched unit through a cycle. Unit made ice. All functions pass; used 1 WP2217224 (Start device) from stock
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ2
Near Travelers Rest, SC 29690
Larry M.
Job Details:
05/09/2025
Found sump pump not operating. Quoted customer $717.24 to replace sump pump and water valve. Customer declined.
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF577KPS02
Near Pickens, SC 29671
Frank
Job Details:
05/09/2025
No errors present. Tested fans ok.. sound coming from damper motor ; ordrng 1 WPW10479155 (Damper control) and 1 Jobcodel14 (Job code l14)
We serviced a
WHIRLPOOL RANGE
Model WFE770H0FZ
Near Simpsonville, SC 29681
Carl
Job Details:
05/09/2025
Found bad connection at the oven control reinstalled molex applied power cycled unit to ck operation unit ck ok
We serviced a
WHIRLPOOL DRYER
Model GEW9200LW1
Near Salem, SC 29676
Frank
Job Details:
05/09/2025
Unit is shutting off prematurely.. ordering control and sensor.; ordrng 1 3980062 (Control nla) and 1 WP3406653 (Sensor harness) and 1 WP8577274 (Thermistor) and 1 Jobcodel14 (Job code l14)
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Seneca, SC 29672
Frank
Job Details:
05/09/2025
"Tested cycle, found no leaking.. brought legs down more noticed motor going all the way to floor."
We serviced a
AMANA DRYER
Model NED4655EW1
Near Seneca, SC 29678
Frank
Job Details:
05/09/2025
Found belt broke drum not turning. Replaced dryer repair kit rollers and idler tested cycle running as intended
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Seneca, SC 29678
Frank
Job Details:
05/09/2025
Replaced control calibration ok cycle working ok
We serviced a
KITCHENAID ICE MACHINE
Model KUID508HPS01
Near Seneca, SC 29678
Frank
Job Details:
05/09/2025
"Found water runs too long over filling reservoir could be melting ice in cabinet. Noticed plate wasn't evenly freezing water, cleaned with steel wool.. led light out not working ; ordrng 1 W11542867 (Pump) and 1 Jobcodel14 (Job code l14) and 1 W11034363 (Control) and 1 W10492487 (Led light) and 1 W11221357 (Reed switch)"
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS10
Near Spartanburg, SC 29306
Sam
Job Details:
05/09/2025
Found unit making loud noise from fan. Customer also stated unit was starting fan on its own randomly. Units control mostly likely at fault. Will order fan and control for repair. Will return with parts.; ordrng 1 2man (2 man) and 1 L14 (L14)
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Boiling Springs, SC 29316
Sam
Job Details:
05/09/2025
Unit constantly draining. Found unit f3e1 error code. Unit does not stop draining. Pressure tube checks ok. Needs new control. Will order control. ; ordrng 1 W11603810 (Control) and 1 L14 (L14)
We serviced a
WHIRLPOOL DRYER
Model WED9200SQ0
Near Greer, SC 29651
Chris
Job Details:
05/09/2025
Unit has multiple control faults. Parts unavailable. Called third party team and spoke with Nikki. Unit is unrepairable. File number for call is 7741510889
We serviced a
MAYTAG WASHER
Model MVW6230HW0
Near Taylors, SC 29687
Chris
Job Details:
05/09/2025
"Found worn cam and belt. Replaced from stock . Unit check is ok; used 1 W10721967 (Cam), and 1 W11239857 (Belt) from stock"
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Taylors, SC 29687
Chris
Job Details:
05/09/2025
Found shorted broken slider . Replaced from stock. Unit check is ok ; used 1 W10734521 (Slider) from stock
We serviced a
KITCHENAID RANGE
Model KSGB900ESS6
Near Taylors, SC 29687
Chris
Job Details:
05/09/2025
Installed new parts.Unit check is ok
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Greer, SC 29650
Chris
Job Details:
05/09/2025
Installed new control . Unit check is ok
We serviced a
MAYTAG DRYER
Model MEDB835DW4
Near Greer, SC 29651
Chris
Job Details:
05/09/2025
Unit has open heater. Gave customer a bluebook estimate for repair at $484.54. Installed new heater . Unit check is ok. ; used 1 WP3387747 (Heater) from stock
We serviced a
MAYTAG OVEN
Model MER8700DS1
Near Mauldin, SC 29662
Nathan
Job Details:
05/09/2025
Found control not sending voltage to bake element and bake element testing at 2.2 mega ohms which is out of range. Also ordering temp probe. Ordering control and bake element. Office will call and schedule return visit when parts arrive. ; ordrng 1 WPW10655845 (ACU) and 1 W10779716 (Bake element) and 1 J13laborcode (J13 labor code) and 1 W10833885 (Temp sensor probe) and 1 Tribleshassensorandelement (Tribles has sensor and element)
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Simpsonville, SC 29681
Carl
Job Details:
05/09/2025
Ran diagnostics found pressure switch out of range l14; ordrng 1 W11603810 (Acu)
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Simpsonville, SC 29681
Nathan
Job Details:
05/09/2025
Replaced lower wiring harness and tested operation after calibrating. Everythings performing as designed.
We serviced a
KITCHENAID DISHWASHER
Model KDTE254ESS2
Near Mauldin, SC 29662
Nathan
Job Details:
05/09/2025
"User interface is stuck showing F2E2 error code. Ordering control, user interface, tub gasket,door gasket, user, over fill switch, and interface gasket. When removing kick plate I found severe water stains towards front of dishwasher soaking insulation on kick plate. Suspect its migrating from console or door seals. Couldnt run dishwasher to prove. May need additional parts after replacing above items listed. ; ordrng 1 W10902370 (User interface) and 1 W10866124 (ACU) and 1 W10909089 (Inner door seal) and 1 W11213719 (Console seal) and 1 W11177741 (Tub gasket) and 1 WPW10195039 (Over fill switch) and 1 U18laborcode (U18labor code) and 1 Raisefrontfeettoleanbackwhenbackouttorepair (Raise front feet to lean back when back out to repair)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT108FFDW04
Near Walhalla, SC 29691
Matt
Job Details:
05/09/2025
Replaced ice maker and installed water line and pressure reducer. Evacuated system. Replaced compressor. Pressure tested with nitrogen. Unit held pressure. Pulled a vacuum and worked in 1.76 oz of r600a checks o.k
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPW2
Near Hendersonville, NC 28739
Brian
Job Details:
05/09/2025
"Installed new control. Tested unit observing for leaks and proper functions. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
JENN AIR DISHWASHER
Model JDB9000CWS2
Near Greenville, SC 29615
Nathan
Job Details:
05/09/2025
Sump is leaking. Quoted $657.81 and has 30 days to accept quote. Says hes going to get a new one. Left kick plate off per homeowner request so floor drys.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM13
Near Easley, SC 29640
Larry M.
Job Details:
05/09/2025
Replaced evaporator fan. All functions pass.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS06
Near Easley, SC 29642
Larry M.
Job Details:
05/09/2025
Found control box making a tapping noise. ; ordrng 1 W11567409 (Control) and 1 J13jobcode (J13 job code)
We serviced a
WHIRLPOOL KITCHEN
Model WFES3030RS0
Near Inman, SC 29349
Chris
Job Details:
05/09/2025
Found door not seated into Receivers correctly. Reseated door . Unit Check is ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ17
Near Greenville, SC 29611
Larry M.
Job Details:
05/09/2025
Replaced coupling and motor. Found ice bucket binding up. Will need ice bucket. ; ordrng 1 WPW10670845 (Ice bucket)
We serviced a
AMANA WASHER
Model NTW4516FW
Near Greenville, SC 29617
Larry M.
Job Details:
05/09/2025
Found drain pump running continuously. Found pressure sensor broken. Will need control board ; ordrng 1 W11603811 (Control board) and 1 J13jobcode (J13 job code)
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS0
Near Flat Rock, NC 28731
Brian
Job Details:
05/09/2025
"Installed wash motor, main control and turbidity sensor. Tested unit and completed test cycle. Tested again, and found it shutting off the same way it did before. Contacted tech support and spoke to Rick. Informed him of situation. He said it must be an issue with the wire harness itself. Main wire harness (W11568793) console (W11416457) needed. Sr number (7741538184) ; ordrng 1 W11568793 (Wire harness) and 1 W11416457 (Console) and 1 Q16 (Job code)"
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Inman, SC 29349
Chris
Job Details:
05/08/2025
Installed new control . Unit check is ok
We serviced a
KITCHEN AID RANGE
Model KSEG700ESS7
Near Simpsonville, SC 29681
Carl
Job Details:
05/08/2025
Installed new temp probe cycled unit to 350 unit. Ck ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM13
Near Greenville, SC 29607
Nathan
Job Details:
05/08/2025
Removed machine compartment cover and moved around some refrigerant lines that could possibly be causing a noise issues cycled ice maker and it had water in ice maker indicating its most likely not a dry valve noise. Replaced evaporator fan motor and refrigerator was much quieter. Everythings performing as designed.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFF3436RZ00
Near Fountain Inn, SC 29644
Carl
Job Details:
05/08/2025
Installed new Led no voltage ck door switchs open and no voltage out of p2 on board n15; ordrng 2 W11396033 (Switch)s and 1 W11548534 (Acu)
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Boiling Springs, SC 29316
Sam
Job Details:
05/08/2025
Installed handle to units door. Reinstalled door. Opened and closed door multiple times. All functions pass.
We serviced a
MAYTAG WASHER
Model MVWX655DW1
Near Boiling Springs, SC 29316
Sam
Job Details:
05/08/2025
Found unit shaking violently when in spin. Even with no clothes unit shakes violently. Checked suspension. Suspension rods very weak. Bounces multiple times before stopping. Replaced suspension rods from pre ID. Cycled unit though rinse and spin with load of clothes. Unit no longer shaking violently. Unit progressing cycle properly. All functions pass.
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Gaffney, SC 29340
Sam
Job Details:
05/08/2025
Found unit constantly draining. Checked error codes. Found with f3e1 error code. Checked pressure hose. Pressure hose checks ok. Unit needs new control. New control parts and labor covered under S153EB job code. Will order for repair.; ordrng 1 W11603811 (Control) and 1 J13 (J13)
We serviced a
JENN-AIR ICE MACHINE
Model JUIFN15HX02
Near Asheville, NC 28804
Brian
Job Details:
05/08/2025
Tested unit in diagnostic. Found water not entering unit. Removed filter and found water now entering. Customer installed a new filter and the same issue occurred. Also found water dripping from filter housing. New Filter housing (W11266112) needed. ; ordrng 1 W11266112 (Filter housing) and 1 L14 (Job code)
We serviced a
WHIRLPOOL COOKTOP
Model WFES3330RZ0
Near Spartanburg, SC 29306
Sam
Job Details:
05/08/2025
Found units back right of cooktop lifting and not secure. Removed cooktop. Found clip that holds in back right of cooktop warped. Tried to adjust hook portion of clip but clip will still not hook to cooktop. Cooktop checks ok. Will order clip for repair.; ordrng 1 W10607641 (Clip) and 1 W10607642 (Clip right side) and 1 L14 (L14)
We serviced a
WHIRLPOOL OVEN
Model WFG320M0MS0
Near Spartanburg, SC 29306
Sam
Job Details:
05/08/2025
Installed new harness to unit. Cycled all burners and bake. All components operating. No longer tripping breaker. All functions pass.
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Spartanburg, SC 29306
Sam
Job Details:
05/08/2025
Found unit with f1e0 error code. Checked connections. Connections secure. Unit needs new board. Will order board for repair.; ordrng 1 W11764616 (Control) and 1 L14 (L14)
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Swannanoa, NC 28778
Brian
Job Details:
05/08/2025
"Installed new control. Calibrated and tested unit observeing for leaks and proper functions. At this time, all operations ok with no leaks detected"
We serviced a
MAYTAG WASHER
Model MVW4505MW2
Near Fairview, NC 28730
Brian
Job Details:
05/08/2025
"F0e9 (off balance pause) tested unit in diagnostic and found unit completing without issues. Found unit slightly leaning to the left. Leveled unit. Checked suspension and found it ok. Reviewed proper loading procedures, with customer, and informed customer of the importance of proper cycle selection with customer. Calibrated unit. At this time, all operations ok with no leaks detected."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDM11
Near Travelers Rest, SC 29690
Larry M.
Job Details:
05/08/2025
Found evaporator fan stuck between plastic casing. Fixed fan. Defrosted freezer. Called Tech-Line to report findings. All functions passSR.7741532218
We serviced a
WHIRLPOOL DRYER
Model WED7120HC3
Near Mills River, NC 28704
Brian
Job Details:
05/08/2025
Installed new heating element and removed lint build up. Tested and found all operations ok at this time.
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Easley, SC 29640
Larry M.
Job Details:
05/08/2025
Found door difficult to close. Will order latch assembly. ; ordrng 1 W11684591 (Plug)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRMF3636RZ00
Near Greenville, SC 29607
Nathan
Job Details:
05/08/2025
"Ordering filter reservoir for leaking,valve for intermittent loud noises, and foam gaskets for condensation on freezer door. Office will call and schedule return visit when parts arrive. ; ordrng 1 W11548535 (Valve) and 1 W11706229 (Filter housing) and 2 W11159728 (Foam gaskets)s and 1 1/4-5/16Johnguestcheckvalve(cantfindpartnumbernotcriticalthoughtoorder) (1/4-5/16 John guest check valve(cant find part number not critical though to order)) and 1 N15laborcode (N15 labor code)"
We serviced a
MAYTAG WASHER
Model MFW7020RF0
Near Spartanburg, SC 29302
Sam
Job Details:
05/08/2025
Installed latch to unit. Cycled unit through quick wash. Units latch locking. Unit progressing cycle. All components activating. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ12
Near Simpsonville, SC 29680
Carl
Job Details:
05/08/2025
Found bucket cracked and separator jamming n15; ordrng 1 WPW10353552 (Separator) and 1 W11185686 (Bucket ice) and 1 WPW10309866 (Silianoid) and 1 N15 (Labor)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Greenville, SC 29615
Nathan
Job Details:
05/08/2025
Compressor is seized and pulling locked rotor amps. Ordering sealed system components. Has a garage refrigerator theyre using until we get parts in. Office will call and schedule return visit when parts arrive. ; ordrng 1 W11727250 (Compressor) and 1 W11506635 (Process stub) and 1 W11598434 (Evaporator) and 1 X20laborcode (X20 labor code) and 1 W11109499 (Drier) and 1 W11504447 (Lock ring coupler)
We serviced a
AMANA REFRIGERATOR
Model ART308FFDM11
Near Simpsonville, SC 29680
Carl
Job Details:
05/08/2025
Found control unresponsive heater. And limit open n15; ordrng 1 W11562214 (Harness) and 1 W11660617 (Control) and 1 W11562215 (Def heater)
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ2
Near Greenville, SC 29615
Carl
Job Details:
05/08/2025
Found edge of panel rusty installed new front panel unit ck ok
We serviced a
IKEA MICROWAVE
Model IMBS104GSS02
Near Spartanburg, SC 29303
Sam
Job Details:
05/08/2025
"Installed hinges, lamp and arm/rivet, cycled door of unit. Door now closing. Unit heating. All functions pass."
We serviced a
WHIRLPOOL MICROWAVE
Model Koec530pss01
Near Easley, SC 29642
Larry M.
Job Details:
05/08/2025
Found turntable making noise. Will need turntable. Customer states house will be renovated soon and would like to schedule appointment when renovations start so we dont have to remove unit twice. ; ordrng 1 W10911403 (Turn table motor) and 1 W11676353 (Adapter) and 1 2manjobcode (2 man job code) and 1 X20jobcode (X20 job code)
We serviced a
IKEA MICROWAVE
Model IMBS104GSS02
Near Spartanburg, SC 29303
Chris
Job Details:
05/08/2025
Installed new parts. Unit check is ok . New labor authorization is i1e2a30nl2
We serviced a
MAYTAG DRYER
Model MEDB835DW3
Near Greenville, SC 29605
Larry M.
Job Details:
05/08/2025
Found unit coming on. Tested outlet. Correct voltage found. Tested control board. Found no voltage coming to it. Will order control board. ; ordrng 1 W10827974 (Control) and 1 W11126010 (Motor) and 1 W11036551 (Door switch) and 1 W10909685 (Fuse) and 1 280148 (Cutoff tml) and 1 WP8557403 (Thermal fix) and 1 N14jobcode (N14 job code)
We serviced a
MAYTAG WASHER
Model MVWP585GW0
Near Greenville, SC 29609
Nathan
Job Details:
05/08/2025
Replaced ACU and tested operations. Calibration was successfully. Everything should be performing as designed.
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706ESS04
Near Greer, SC 29651
Chris
Job Details:
05/08/2025
Unit has defrost failure . Test 6 shows 02. Gave customer a bluebook estimate for repair at 727.86. Ordering for repair ; ordrng 1 W11249952 (Harness)
We serviced a
KITCHENAID OVEN
Model MODKESC307HBS8
Near Greenville, SC 29617
Larry M.
Job Details:
05/08/2025
Found baking element ground to chassis. Will need heating element. Could not find element in parts catalog. ; ordrng 1 Heatingelement (Heating element) and 1 J13jobcode (J13 job code)
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Travelers Rest, SC 29690
Larry M.
Job Details:
05/08/2025
"Replaced ui, control panel, and door switch. Ran test cycle. All functions pass."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Simpsonville, SC 29681
Carl
Job Details:
05/08/2025
Installed new acu ran diagnostics
We serviced a
WHIRLPOOL OVEN
Model WOD51EC0HS01
Near Duncan, SC 29334
Chris
Job Details:
05/08/2025
Cleaned upper door glass for Customer. Reassembled all 3 pieces . Unit check is ok
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFC704FPS03
Near Campobello, SC 29322
Chris
Job Details:
05/08/2025
"Unit has compressor failure . Compressor doesnt run in test 38,39,40. All fans activate. Unit has sealed system failure. Customer to hold off on repair and cant wait for repair"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ12
Near Inman, SC 29349
Chris
Job Details:
05/08/2025
Installed imk. Unit check is ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDW10
Near Greenville, SC 29605
Nathan
Job Details:
05/08/2025
"Replaced compressor,drier,and evaporator. Pressurized, purged,and vacuumed system. Recharged with r600a indicated on data tag. Everythings performing as designed."
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Inman, SC 29349
Chris
Job Details:
05/08/2025
"Customer states unit doesnt make ice , leaves food crystals on packed goods in in freezer and refrigerator. Customer also states freezer stays between 0- degrees and 30-33 degrees in fresh food section , makes hissing noise and measure to fill doesnt work with low water pressure . Freezer is at 2 degrees and 34 at set point settings, . No faults in test 56 . Unit fills in test 45. Temps in freezer are at 3 degrees and fresh food is at 37. Rear vent is blocked in refrigerator. Customer is using store bought thermometers . Pictures of temps are uploaded . Temps are recorded in pictures. Hissing noise is unit going into defrost. All fans function in test 4. Test 1,2,and 4 check ok . Bin is half full of ice and rotates in test 58. Unit check is ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ06
Near Hendersonville, NC 28792
Matt
Job Details:
05/07/2025
"Evacuated system. Installed new compressor, evaporator and dryer filter. Pressure tested. Unit held pressure. Pulled a vacuum and weighed in 2.4 oz of r600a. Installed water tank, flushed out new tank, checks o.kAuthorization w1e1w90nl1.5"
We serviced a
AMANA WASHER
Model NTW4605EW0
Near Leicester, NC 28748
Brian
Job Details:
05/07/2025
"Customer said unit will run sometimes and sometimes wont . Found f1e2 (motor control fault) f8e1( long fill) f5e2 (lid lock fault). Tested unit in diagnostic and found cold water entering unit slowly . Checked and found incoming water pressure weak. Inspected and found control needed. Installed new control (W11116498). Calibrated and tested unit. At this time, all operations ok with no leaks detected."
We serviced a
WHIRLPOOL DRYER
Model WED500CMW0
Near Greenville, SC 29605
Nathan
Job Details:
05/07/2025
"Dryer has a couple issues. Motor overheats and dryer starts by itself. Ordering blower wheel,motor, encoder,and ACU. Office will call and schedule turn visit when parts arrive. ; ordrng 1 WPW10396039 (Motor) and 1 W10801999 (Blower wheel (I have two in my van at shop)) and 1 W11728028 (ACU) and 1 W11627521 (Encoder) and 1 U18laborcode (U18 labor code)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ19
Near Greenville, SC 29605
Nathan
Job Details:
05/07/2025
Replaced fill tube for holes and evaporator fan motor for noise issues. Put foam around freezer evaporator cover to minimize vibrations Everythings performing as designed.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Asheville, NC 28803
Brian
Job Details:
05/07/2025
"Tested unit in spin cycle with load of clothes in it and found water lines tapping on the back of the machine, but also the pipes going to water shutoff, in wall, tapping against wall interior. Removed load and calibrated and tested unit in diagnostic. All functions are ok. Informed customer that they will need a professional plumber or resolve situation within the wall. Customer understands. At this time, unit functions ok with no leaks detected. Did not move unit."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT541SZDM03
Near Lake Lure, NC 28746
Brian
Job Details:
05/07/2025
Customer said freezer section was freezing over but they thawed it out by leaving it unplugged . Found air channel to fresh food section has ice booking. Tested Hester and found it coming on. Found all fans working properly . Observed frost pattern and found it ok. Both doors sealing ok. Unit is not going into defrost properly. New Harness (W11616409) and control (W11616408) needed. ; ordrng 1 W11616409 (Harness) and 1 W11616408 (Control) and 1 L14 (Job code)
We serviced a
MAYTAG WASHER
Model MVWX655DW1
Near Columbus, NC 28722
Brian
Job Details:
05/07/2025
"Found no saved error codes. Customer said agitator plate was getting stuck and not agitating. Tested unit in diagnostic and unit completed except belt and cam are very noisy. Inspected and found Cam (W10721967) and belt (WPW10006384) needed. Attempted to remove agitator plate and could not. Informed customer that if there is an issue with agitator or hub, we would not be able to complete repairs because components are rusted to gear case. Customer understands . Quoted customer 405.20 to replace belt and cam. Customer did not wish to proceed with repairs at this time. Collected 150 for service call."
We serviced a
KITCHEN AID REFRIGERATOR
Model KFIS29BBMS03
Near Travelers Rest, SC 29690
Larry M.
Job Details:
05/07/2025
Verified water source as well as correct temperature. Cycled ice maker. Ice maker would not cycle. Found Ui not going responsive in diagnostic. ; ordrng 1 W10878990 (Ui)
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Simpsonville, SC 29680
Carl
Job Details:
05/07/2025
Found strike missing installed new strike cycled unit to ck operation unit ck ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ03
Near Simpsonville, SC 29680
Carl
Job Details:
05/07/2025
Imk receiving voltage and valve has aloud noise when activated n15; ordrng 1 W11482383 (Valve) and 1 W11087201 (Heater) and 1 W11658802 (Imk) and 1 N15 (Labor)
We serviced a
WHIRLPOOL DISHWASHER
Model wdf750saym3
Near Easley, SC 29642
Frank
Job Details:
05/07/2025
Found disposal clogged up that's why unit isn't draining.. unit now is draining okay. Customer should get disposal looked at
We serviced a
WHIRLPOOL REFRIGERATOR
Model Wrmf3636rz00
Near Simpsonville, SC 29680
Carl
Job Details:
05/07/2025
Valve noises j13; ordrng 1 W11548535 (Valve)
We serviced a
KITCHENAID OVEN
Model KOSE500ESS20
Near Travelers Rest, SC 29690
Larry M.
Job Details:
05/07/2025
Found unit not responding to commands and showing wiring error message. Replaced Ui and main control. Ran test cycle. All functions pass.
We serviced a
KITCHENAID DISHWASHER
Model KDPM604KPS2
Near Easley, SC 29642
Frank
Job Details:
05/07/2025
The pro wash and tough buttons you cannot select all other buttons are okay no errors present. Unit operating a washing okay; ordrng 1 Jobcodej13 (Job code j13) and 1 W11622505 (Console)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ13
Near Slater-Marietta, SC 29661
Larry M.
Job Details:
05/07/2025
Found fridge door cracked at top. Will need door. Customer requested to send door to Alternate address. 405 Lancaster street Greer sc 29650; ordrng 1 LW10913407 (Fridge door) and 1 J13jobcode (J13 job code)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT314TFDW03
Near Travelers Rest, SC 29690
Larry M.
Job Details:
05/07/2025
Wrong seal came in. Will order correct seal. ; ordrng 1 LW10573334 (Seal)
We serviced a
KITCHEN AID ICE MACHINE
Model KUIX305ESS2
Near Saluda, NC 28773
Brian
Job Details:
05/07/2025
"Installed new circulation pump. Tested unit and found it now filling and water level sensor is responding properly. All other functions ok at this time , with no leaks detected. Did not move unit. Collected 135.63."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS0
Near Greer, SC 29651
Chris
Job Details:
05/07/2025
Installed new parts. Unit check is ok. No leaks
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Duncan, SC 29334
Chris
Job Details:
05/07/2025
Ordeing control for repair ; ordrng 1 W11603810 (Controls)
We serviced a
KITCHENAID DISHWASHER
Model KDFM404KPS2
Near Greer, SC 29650
Chris
Job Details:
05/07/2025
"Customer states unit wont come on . Unit is fully operational. No stored faults . Unit passes automatic test cycle , ran normal cycle . Unit performs as designed"
We serviced a
AMANA DRYER
Model NED4655EW1
Near Taylors, SC 29687
Chris
Job Details:
05/07/2025
Installed new parts. Called trade care team and spoke with Demetrius.double labor denied for cabinet install. Job complete
We serviced a
AMANA DRYER
Model NED4700YQ1
Near Simpsonville, SC 29681
Carl
Job Details:
05/07/2025
Found thermal fuse open installed new thermal fuse cycled unit to ck operation and vent flow advised customer to have vents cleaned ; used 1 WP3392519 (Thermal fuse) from stock
We serviced a
WHIRLPOOL WASHER
Model WTW8500DC5
Near Simpsonville, SC 29681
Carl
Job Details:
05/07/2025
Found slider worn. Installed new slider from t/s ran diagnostics and a test cycle to ck operation unit ck ok; used 1 W10734521 (Slider) from stock
We serviced a
WHIRLPOOL RANGE
Model WFE320M0JS4
Near Greenville, SC 29615
Carl
Job Details:
05/07/2025
Found bad relay on board installed new oven control cycled unit to 350 to ck operation unit ck ok
We serviced a
WHIRLPOOL DRYER
Model WED5605MW0
Near Boiling Springs, SC 29316
Sam
Job Details:
05/07/2025
Customer stated she will put wet clothes inside unit and start a cycle and then cycle will stop after 10-15 minutes. Tested with cycle. Unit stopping. No error codes present. Most likely moisture sensor or control problem. Will order both for repair.; ordrng 1 W11733951 (Ccontrol) and 1 W11583883 (Console) and 1 WPW10298258 (Sensor) and 1 L14 (L14)
We serviced a
MAYTAG DRYER
Model MED6500MBK0
Near Spartanburg, SC 29306
Sam
Job Details:
05/07/2025
Found unit not heating. Checked incoming power. Voltage good. Checked heating element. Element has no continuity. Checked thermal cut off. Cut off thermal also no continuity. Replaced thermal cut off and element. Cycled unit. Unit now heating. All components working. Unit heats and tumbles. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRB322DMBM05
Near Greenville, SC 29607
Nathan
Job Details:
05/07/2025
Had ice maker turned on causing noises. Cycled ice maker to confirm noise and that was it. Turned off ice maker and leveled refrigerator before I left. Everythings performing as designed now.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS0
Near Greenville, SC 29605
Larry M.
Job Details:
05/07/2025
Found hole in drain hose. Replaced drain hose. Ran test cycle. All functions pass
We serviced a
WHIRLPOOL DRYER
Model WED6120HW3
Near Greenville, SC 29607
Nathan
Job Details:
05/07/2025
Quoted $591.22 to replace motor and blower wheel. Part and labor authorization W1E1T00APL1. Replaced blower wheel and motor. Picked up parts from shop. Performing as designed now. ; ordrng 1 PartandlaborauthorizationW1E1T00APL1 (Part and labor authorization W1E1T00APL1)