We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ0
Near Simpsonville, SC 29681
Carl
Job Details:
07/25/2024
Ran diagnostics f7e1 bad wash motor advised customer of repair customer not going to repair unit
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Greenwood, SC 29649
Jerry D.
Job Details:
07/25/2024
"Fill valve inoperable, installed w11130743 from truck stock, cycled unit through test and no leaks found unit checks ok ; used 1 W11130743 (Valve) from stock"
We serviced a
KITCHENAID MICROWAVE
Model KBHS109SSS06
Near Greenville, SC 29617
Larry M.
Job Details:
07/25/2024
"Replaced magnetron, F1e5 error message for inverter came up. Quoted customer $493 to replace inverter. Customer declined repair. $503 owed at this time.; ordrng 1 W10217711 (Inverter)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ06
Near Asheville, NC 28805
Brian
Job Details:
07/25/2024
Tested unit and found defuser motor running loudly. New Diffuser (W11236851) needed. ; ordrng 1 W11236851 (Diffuser) and 1 L14 (Job code)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDM11
Near Fairview, NC 28730
Brian
Job Details:
07/25/2024
"Found control box housing broken. Installed new control box and found all operations ok at this time, with no leaks detected."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Hodges, SC 29653
Jerry D.
Job Details:
07/25/2024
"Called mrs she doesnt want to pay anything she has a extended warranty, if she does unit needs imk, ; saved tckt"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFF5333PV01
Near Flat Rock, NC 28731
Brian
Job Details:
07/25/2024
"Installed new right hand door gasket and damper. Ensured gasket is sealing properly and tested damper. At this time, all operations ok with no unusual noises or leaks detected. Did not move unit."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ08
Near Hendersonville, NC 28739
Brian
Job Details:
07/25/2024
"Found some condensation on top of freezer and pantry door gasket. Gaskets sealing properly. Turned on vertical and horizontal mullians to 100% on. Also found temp settings lower than they should be. Set to recommended settings. Found all fan working ok. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS3
Near Anderson, SC 29625
Frank
Job Details:
07/25/2024
Ran tested.. water coming out of vent when opening after cycle is done.. re programed changed dry level as per pointer w11705834.. leaving open for follow up. Can close after 7/30/24 if not heard from customer with any more problems; O-emld tckt
We serviced a
MAYTAG WASHER
Model MVW5430MW0
Near Seneca, SC 29678
Frank
Job Details:
07/25/2024
Repaired wire harness to drain pump. Wires stretch.. remounted wires.. tested working ok..
We serviced a
WHIRLPOOL DRYER
Model WED5100HW2
Near Walhalla, SC 29691
Frank
Job Details:
07/25/2024
Inspected unit no wires burnt.. turns on heats ok.. cleaned out clogged vent.. tested working ok.
We serviced a
WHIRLPOOL RANGE
Model WFE525S0JS3
Near Walhalla, SC 29691
Frank
Job Details:
07/25/2024
Replaced switch and element tested working ok. Cycling on and off in mid cycles.
We serviced a
KITCHENAID OVEN
Model KSDG950ESS6
Near Canton, NC 28716
Kari
Job Details:
07/25/2024
"Took quick pics, found unit not running bake element. Element showing 16 ohms. Unit broil works need parts for repair rescheduled for 8/6 PM; ordrng 1 W11100513 (Main acu) and 1 L14 (Job code) and 1 W10779716 (Bake element)"
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Waynesville, NC 28786
Kari
Job Details:
07/25/2024
"Andrew @ techline 7739038126Took quick pics, found unit showing 0-9 off balance pause and a 7-7 motor unable to reach target rpm. Ran diagnostic cycle and found all functions completed as normal. Ran regular drain and spin and found unit to be normal. Taped drain hose into u-collar because cust is concerned it will come out in spin. U-collar is also zip tied to hot hose. Put a level on all 4 sides of unit and found it to be nearly perfectly square on floor. Unit is on a tile floor. Tested suspension, basket bounced once and settled into center. Called techline and spoke with Andrew I went through history and what I found today. He asked me to do a load of towel. I put 5 full sized bath towels on rinse and spin, set towels loosely in a donut around the outside of basket. It shakes a bit when spinning on the outside but I had it where I could look in lid while it was running and the basket is centered when spinning. Unit is functioning properly"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ00
Near Mauldin, SC 29662
Carl
Job Details:
07/25/2024
Installed new tube and facia heater ran diagnostics checked ok
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Moore, SC 29369
Sam
Job Details:
07/25/2024
Found unit not drying clothes. Unit has error code about vent being clogged or kinked. Found kink in vent behind unit because of excess tubing. Removed excess tubing. Cycled unit through timed dry. All components working. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ11
Near Spartanburg, SC 29302
Sam
Job Details:
07/25/2024
Found units dispenser not wanting to dispense water or ice. Found that small black plastic front covers of dispenser were causing units dispenser to get stuck and not allow water to dispense. Adjusted front covers of dispenser. Unit now dispensing water and ice properly. All functions pass.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS0
Near Spartanburg, SC 29306
Sam
Job Details:
07/25/2024
Found unit not heating. Checked for error codes. No error codes present. Checked connections to heating element underneath unit. Found one side of heating element had loose connection not fully seated on to element. Re seated connection. Cycled unit through diagnostics cycle. All components working. All functions pass.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS0
Near Boiling Springs, SC 29316
Sam
Job Details:
07/25/2024
"Found unit not draining water. Found units connection on drain pump not fully seated. Reseated and secured connection on drain pump. Cycled unit through diagnostics cycle. Unit fills, recirculates, heats and drains. All functions pass."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHV08
Near Boiling Springs, SC 29316
Sam
Job Details:
07/25/2024
Installed all parts. Units ice maker cycling and filled with water. Units light now comes on and off properly. All components working. All functions pass.
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Easley, SC 29640
Frank
Job Details:
07/24/2024
Replaced suspension. Tested quick cycle and spin with clothes. Working ok not shaking
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS2
Near Greer, SC 29651
Chris
Job Details:
07/24/2024
Vent wax fault is gone and long drain fault is stored. Unit has weak wash motor. Wash motor is weak causing long drain fault . Ordeing for repair ; ordrng 1 W11416362 (Wash motor) and 1 N15
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Fountain Inn, SC 29644
Carl
Job Details:
07/24/2024
Installed new timer and knob cycled unit several times to check operation unit ck ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Pendleton, SC 29670
Frank
Job Details:
07/24/2024
EVAP Fan rattling.. damper rattling need to replace.. ; ordrng 1 WP2315549 (Fan) and 1 W11236851 (Air diffuser) and 1 Jobcodel14 (Job code l14)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM12
Near Fountain Inn, SC 29644
Carl
Job Details:
07/24/2024
Adjusted door and Used hair dryer to adjust door seal unit ck ok
We serviced a
AMANA REFRIGERATOR
Model ART308FFDM11
Near Simpsonville, SC 29680
Carl
Job Details:
07/24/2024
Used hair dryer to adjust door seals unit ck ok
We serviced a
MAYTAG WASHER
Model MVWC465HW3
Near Asheville, NC 28803
Brian
Job Details:
07/24/2024
"Found no saved error codes. Tested unit multiple times inspecting all water lines and drain hoses and found no evidence of leaking. Checked drain pump and tub and water valve and found no leaking. Tested unit in high spin and four rear panel vibrating and drain hose tapping on wall. Adjusted rear panel and secured drain hose. Calibrated unit and tested again observing for leaks and proper functions. At this time, all operations ok with no leaks detected. Reviewed proper loading procedures with customer."
We serviced a
WHIRLPOOL RANGE
Model WEE745H0LZ4
Near Anderson, SC 29621
Jerry D.
Job Details:
07/24/2024
Cycled unit through test and unit checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ1
Near Belton, SC 29627
Jerry D.
Job Details:
07/24/2024
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS1
Near Hendersonville, NC 28792
Brian
Job Details:
07/24/2024
"Installed parts ordered. Tested unit multiple times observing for leaks and proper functions. At this time, all operations ok with no leaks detected.m"
We serviced a
WHIRLPOOL WASHER
Model WTW6157PW0
Near Greenville, SC 29609
Larry M.
Job Details:
07/24/2024
Replaced main control and ui. Ran test cycle. Checks ok.
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Columbus, NC 28722
Brian
Job Details:
07/24/2024
Found temps ok. Ice level sensor ok. Found e5 (timed ice) error code. Tested ice box fan and found it operating ok at this time. Test cycled ice maker and found it not completing cycle and also not filling. Fill tube frozen. Tested and found fill tube heater dropping voltage when moving harness. Ice maker (W11658802) harness (W10673048) fill tube heater (W11226501); ordrng 1 W11658802 (Ice maker) and 1 W10673048 (Harness) and 1 W11226501 (Fill tube heater) and 1 L14 (Job code)
We serviced a
JENN AIR REFRIGERATOR
Model JFFCF72DKL04
Near Columbus, NC 28722
Brian
Job Details:
07/24/2024
Installed new right hand door gasket. Tested and found all operations ok at this time. Did not move unit.
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFC704FSS00
Near Columbus, NC 28722
Brian
Job Details:
07/24/2024
"Installed all parts according to service pointers. Tested water and ice maker and found them ok. All fans working properly with good frost pattern. At this time, all operations ok with no leaks detected."
We serviced a
WHIRLPOOL FREEZER
Model WZF34X16DW10
Near Easley, SC 29640
Frank
Job Details:
07/24/2024
Compressor not turning on. Getting 120 v. Replaced starter. Not coming on.. not cooling..; ordrng 1 W11547313 (Compressor) and 1 Jobcodex20 (Job code x20) and 1 w11506635 (Access port) and 1 wpw10143759 (Dryer) and 1 Sealedsystemtech (Sealed system tech) and 1 R600a (R600a)
We serviced a
AMANA DISHWASHER
Model ADB1400AMS1
Near Simpsonville, SC 29680
Carl
Job Details:
07/24/2024
Found door latch closed in. The open position reset door switch closed door was able to start unit ck ok
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HZ09
Near Moore, SC 29369
Sam
Job Details:
07/24/2024
Found units class and rollers warped causing unit to make loud rumbling sound when in use. Will order tray and rollers for repair.; ordrng 1 W11685581 (Glass tray) and 1 W11252182 (Rollers)
We serviced a
AMANA DISHWASHER
Model ADB1400AMS1
Near Inman, SC 29349
Sam
Job Details:
07/24/2024
"Found unit not washing dishes. Unit has f4e3 error code for pump and motor. Checked connections, all connections secure. Will order pump and motor for repair.; ordrng 1 W11613570 (Pump and motor)"
We serviced a
WHIRLPOOL RANGE
Model WEG745H0LZ5
Near Inman, SC 29349
Sam
Job Details:
07/24/2024
"Installed panel. Cycled burners, bake and broil. All components working. All functions pass."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHW08
Near Boiling Springs, SC 29316
Sam
Job Details:
07/24/2024
Found unit making rattling rubbing noise. Found units evaporator fan hitting against panel. Adjusted panel and evaporator fan. Rattling noise no longer occurs when cycling fan in diagnostics. All functions pass.
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ2
Near Boiling Springs, SC 29316
Sam
Job Details:
07/24/2024
Installed pump and motor. Cycled unit through diagnostics cycle. All components working. No leaks found throughout cycle. All functions pass.
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC2
Near Greer, SC 29651
Chris
Job Details:
07/24/2024
Customer states unit uses low water levels and unit has low agitation strength. Customer mentions adding water to unit. Unit has off balance load faults stored . Unit passes automatic diagnostics cycle. Rotor is tight and slider is in good shape . Unit has low and high agitation speeds. Showed customer service pointer W11499341.demonstrated bulky and heavy selections. Unit filled 3/4 with water. No fault of unit. Unit check is ok
We serviced a
WHIRLPOOL DRYER
Model WGD8620HC3
Near Piedmont, SC 29673
Jerry D.
Job Details:
07/24/2024
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
MAYTAG WASHER
Model MVW6500MBK1
Near Seneca, SC 29678
Frank
Job Details:
07/24/2024
Strike broke.. replaced tested lock.. working ok
We serviced a
WHIRLPOOL WASHER/DRYER COM
Model CET9100GQ2
Near Seneca, SC 29672
Frank
Job Details:
07/24/2024
F27 code flashing.. still a lot of suds called TechlineSr 7739563932. ..
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Westminster, SC 29693
Frank
Job Details:
07/24/2024
Ran diagnostics mode in mode 3 damper rattling.. a little condensation build up in both sections. Re check sealing to cabinet..; ordrng 1 W11236851 (Diffuser) and 1 Jobcodel14 (Job cod3 l14)
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706EBS00
Near Easley, SC 29640
Larry M.
Job Details:
07/24/2024
Found unit out of refrigerant. Removed rear cover and evap cover inside of the refrigerator. Charged system 5.5 oz Found leak in inner cabinet.Called and reported to techline. 7739564068 SR number
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHS5
Near Gaffney, SC 29341
Sam
Job Details:
07/24/2024
Installed pump and motor. Cycled unit through diagnostic cycle. No leaks occurred throughout cycle. All components working. All functions pass.
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ2
Near Gaffney, SC 29341
Sam
Job Details:
07/24/2024
Found washer not wanting to agitate or spin. Just wills with water and sits there doing nothing and drains after about 5 minutes. Lid never locking possibly control or lid lock failure. Checked for error codes. Only error codes found was for long fill and no fill. Unit also starts and fills with water without money being put in it. Will order parts for repair.; ordrng 1 WPW10482836 (Lid lock) and 1 W11712987 (Control) and 1 W11126319 (Coin chute) and 1 WP8576635 (Bolt) and 1 W11212745 (Actuator)
We serviced a
KITCHEN AID REFRIGERATOR
Model KBSD608ESS00
Near Greenville, SC 29615
Chris
Job Details:
07/24/2024
"Customer states Mr appliance previously checked unit and tech told her there was a shortage of wire behind optic housing not sending voltage to imk . Optics do not illuminate at all.removed optics. No damage wire . Jumped contact T and H and imk began to harvest .When wiggling optics they illuminated.optics have short. Gave customer a bluebook estimate for repair $659.78.when removing emitter it had very loose contacts. Installed new emitter kit. Imk began to harvest , unit check is ok ; used 1 W11629974 (Control) from stock"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ1
Near Greenville, SC 29615
Chris
Job Details:
07/24/2024
Unit has frozen ui. Ordeing for repair ; ordrng 1 W11660284 (Console) and 1 W11632709 (Ui) and 1 W11672039 (Contrl)
We serviced a
WHIRLPOOL OVEN
Model WFG525S0JZ5
Near Taylors, SC 29687
Chris
Job Details:
07/24/2024
Installed new parts. Unit check is ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ0C
Near Taylors, SC 29687
Chris
Job Details:
07/24/2024
Fresh food is at 37 and freezer is at 0. Unit makes ice. Customer states unit made odd noise the other day . Today at visit functions make normal noise. Compressor and fan have normal and healthy noise . No defrost or sealed system problem. Customer present while all check being performed. Unit check is ok
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KBS2
Near Simpsonville, SC 29681
Carl
Job Details:
07/24/2024
Inner door leaking one buttons do not respond and panel is dis colored l14; ordrng 1 W11416371 (Panel) and 1 W11559689 (Inner door panel) and 1 W11622490 (Console) and 1 L14 (Labor)
We serviced a
WHIRLPOOL DRYER
Model WED5010LW1
Near Taylors, SC 29687
Chris
Job Details:
07/24/2024
Customer states clothes come out with funny smell. Customer states unit smells like a dead rodent. Customer states higher the temp setting the worse it smells. Unit has no Stored faults . Vent is clean . Disassembled unit and vent with customer present . Unit is clean. Nothing in blower or unit . No pets in home. Unit reaches 133 degrees and cycles off. Temps are at manufacture spec. Advised customer there is no possible way a dryer can make odors Customer is referring too. Cut vent hose down to shorter lengths. Advised customer about soap usage and cleaning washer . Unit check Is ok.
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS1
Near Greenville, SC 29609
Chris
Job Details:
07/24/2024
Unit flashes f6-e1 fault . User interface fault . Removed panel to inspect . Removed UI connection and reseated. Fault went away and UI became active. No other faults. Ran diagnostics. Unit check is ok
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Simpsonville, SC 29680
Jerry D.
Job Details:
07/24/2024
Installed listed parts cycled unit through test and unit checks ok
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Simpsonville, SC 29680
Jerry D.
Job Details:
07/24/2024
Installed listed parts cycled unit through test and unit checks ok
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Fountain Inn, SC 29644
Jerry D.
Job Details:
07/24/2024
Installed listed parts cycled unit through test and unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ07
Near Pauline, SC 29374
Sam
Job Details:
07/24/2024
"Found unit not cooling still. Checked for leaks could not locate any leaks with leak detector spray. Compressor running but units temperature in freezer is 44 and temperature in refrigerator is 62. Called MA he said unit is either low in refrigerant or has a restriction in the drier filter, will order parts.; ordrng 1 R600a (R600a) and 1 Sealedsystemtech (Sealed system tech) and 1 Lockring (Lock ring) and 1 W11557425 (Compressor) and 1 W11109499 (Drier filter) and 1 W11550396 (Evaporator) and 1 X20 (X20)"
We serviced a
WHIRLPOOL RANGE
Model KFGD500ESS11
Near Leicester, NC 28748
Kari
Job Details:
07/23/2024
Installed new regulator and leaked checked while running both ovens and top at the same time. No leaks detected. Unit checks ok
We serviced a
KITCHENAID RANGE
Model KDRS483VSS02
Near Greer, SC 29651
Chris
Job Details:
07/23/2024
Unit is pro style. Unit has f6 faults . Unit runs without prompting unit to run. Unit is called appliance manager on tech sheet but referenced differently on break down . Called tech line and spoke with Andrew. Andrew advised to change appliance manger . Gave customer a bluebook estimate for repair at $905.95..ordeing for repair . ; ordrng 1 WPW10116185 (Control) and 1 Q16
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Candler, NC 28715
Kari
Job Details:
07/23/2024
Installed parts unit checks ok
We serviced a
WHIRLPOOL LAUNDRY CENTER
Model WTW8127LW2
Near Fountain Inn, SC 29644
Carl
Job Details:
07/23/2024
Ran diagnostics error code acu not communicating and lid switch damaged ; ordrng 1 W11700916 (Lid switch) and 1 W11621180 (Acu)
We serviced a
WHIRLPOOL WASHER
Model wtw5010lw0
Near Easley, SC 29640
Carl
Job Details:
07/23/2024
New tub installed need lid switch ; ordrng 1 W11513248 (Lid switch)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ04
Near Easley, SC 29640
Carl
Job Details:
07/23/2024
Installed new facia and fill tube heater and handles ran diagnostics checked ok they will hook unit up and run the ink
We serviced a
WHIRLPOOL RANGE
Model WFE525S0JS4
Near Campobello, SC 29322
Chris
Job Details:
07/23/2024
Customer has been shipped parts by dealer that she doesnt need. Installed door correctly. Unit check is ok
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Easley, SC 29640
Carl
Job Details:
07/23/2024
Installed new motor and control cycled unit to ck operation unit ck ok
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ0
Near Duncan, SC 29334
Chris
Job Details:
07/23/2024
Unit un installed upon arrival . Customer states unit leaks and has been leaking for sometime . Floors damaged underneath unit . Unit leaking from heater bushing . Installed new heater unit check is ok . Customer paid $150 svc fee ; used 1 Special Project code S17304 from stock
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Franklin, NC 28734
Brian
Job Details:
07/23/2024
"In tap root farms development. Tested unit and found excess suds in unit. While testing unit I observed all hoses and gaskets and found no leaking. I did find unit leaning forward. Leveled unit and recommended customer switch detergents and informed customer of the importance of keeping other soaps or detergents out of dishwasher. Customer understood. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
WHIRLPOOL REFRIGERATOR
Model krmf706ebs01
Near Flat Rock, NC 28731
Brian
Job Details:
07/23/2024
Found unit cooling properly when I arrived. Found some ice build up on freezer evaporator. Stopped fan manually and found unit unit powering off and then coming back on and giving power outage code. Found deli ui had no moisture or corrosion. Contacted tech support and spoke to Kirt. He recommended replacing the freezer evaporator fan. Sr number (7739559083) New Freezer Evaporator fan (W11249952) needed. Quoted customer 502.97 to complete repairs. Customer did not wish to proceed with repairs at this time. Collected 150 for service call.
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF305ESS00
Near Hendersonville, NC 28791
Brian
Job Details:
07/23/2024
"Test cycled ice maker and found it getting proper voltage but not cycling. New Ice maker (W10884390) needed.quoted customer 418.54 to complete repairs. Customer wished to proceed. Installed new ice maker and tested. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDB05
Near Hendersonville, NC 28791
Brian
Job Details:
07/23/2024
"Found ice maker fill tube out of position, and causing water to spill into freezer floor. Removed ice build up and adjusted fill tube. Tested and found all operations ok at this time, with no leaks detected. Did not move unit."
We serviced a
KITCHEN AID RANGE
Model KSEG950ESS0
Near Brevard, NC 28712
Brian
Job Details:
07/23/2024
"Found f2e1 (stuck key) F9e0 (product mis-wire) error codes. Tested and found no elements on unit heating and found display fading, at times. Also found downdraft capacitor leaking. Inspected and found unit getting proper voltage but not sending any to elements. Capacitor (W11209781) Control panel (W10915815) Main control (W11100515) and Display (WPW10603096) needed. Main control was installed wining the past year, so part cost would be covered under part warranty. Quoted customer 1208.87 to complete repairs. Informed customer that due to nature of issues, further repairs may be needed resulting in further charges. Customer understands and does not wish to proceed with repairs at this time. Collected 150 for service call."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ04
Near Pelzer, SC 29669
Jerry D.
Job Details:
07/23/2024
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
WHIRLPOOL RANGE
Model WFG515S0MS1
Near Travelers Rest, SC 29690
Larry M.
Job Details:
07/23/2024
Found right front burner not lighting immediately. Found little to no resistance in harness. Ordering harness and spark module. ; ordrng 1 W11701337 (Harness) and 1 W11162730 (Spark module)
We serviced a
KITCHEN AID REFRIGERATOR
Model KBFO42FTX00
Near Piedmont, SC 29673
Jerry D.
Job Details:
07/23/2024
Mr doesnt need service now
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW01
Near Piedmont, SC 29673
Jerry D.
Job Details:
07/23/2024
"Freezer door low, shimmed door up with 489467 from truck stock, cycled unit through test nit chks ok"
We serviced a
WHIRLPOOL DRYER
Model ned4655ew1
Near Easley, SC 29640
Carl
Job Details:
07/23/2024
Found motor berrings damaged installed new motor cycled unit ck ok
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706EBS01
Near Liberty, SC 29657
Jerry D.
Job Details:
07/23/2024
"On arrival found frez temp 15 and fresh temp 43, found frez fan motor not running, fresh evaperator frozen, also found display not operating properly, also drawer broken and holding frez door open, also found frost in frez , serv bulletin, ordering, W19; ordrng 1 W10564680 (Assy) and 1 W11106553 (Interface) and 1 W10788814 (Supply) and 1 W10811365 (Cntrl) and 1 W10624574 (Supply) and 1 W10864519 (Kit) and 1 W11039078 (Motor evaperator) and 1 W10799016 (Motor) and 1 W19 (W19)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS331SDHM00
Near Easley, SC 29642
Frank
Job Details:
07/23/2024
Replaced filter housing.. used customers filter tested flow.. water coming out good now..
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Pickens, SC 29671
Frank
Job Details:
07/23/2024
Belt broke replaced belt tested. Turning and heating ok.; used 1 4392065 from stock
We serviced a
JENN-AIR FREEZER
Model JBZFL24IGX00
Near Salem, SC 29676
Frank
Job Details:
07/23/2024
"Frost build up in freezer.. temp 7 degrees.. ice maker not cycling in test 120.. replacing ice maker door gasket.. crisper drawer front broke, replacing Quoted 928.79. Paid 464.40. Owe 464.39; ordrng 1 W11646196 (Ice maker assembly) and 1 W11038431 (Gasket door) and 1 W11245187 (Crisper pan)"
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Simpsonville, SC 29680
Carl
Job Details:
07/23/2024
Found blower wheel disengageGED from the plastic wheel j13 ; ordrng 1 WP697772 (Blower wheel) and 1 J13 (Labor)
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Greenville, SC 29617
Larry M.
Job Details:
07/23/2024
Replaced cam kit and belt. Ran test cycle. Checks ok
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS1
Near Lake Junaluska, NC 28745
Kari
Job Details:
07/23/2024
"Took quick pics, found unit leaking from both sides, found the gasket on the inside had some pinch marks and you can see water marks on inside door panel where it was running down the sides. Installed new gasket. Also found vent leaving too much condensation. Followed SP W11705834 and changed vent settings. Ran normal cycle. Unit checks ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ18
Near Waynesville, NC 28786
Kari
Job Details:
07/23/2024
"Took quick pics, found units kick plate smashed up. Took kickplate off and found condenser hanging and snaps in bottom of fridge that keep condenser in place are also smashed and twisted up. Part of the condenser is bent and has scrapes in the black coating where you can see silver now. Called techline spoke with Derek I sent him pictures of broken clips and bent condenser. He says because the clips are broken off unit is non repairable 7739556178. He told me to tell customer to call customer service to complete the request."
We serviced a
KITCHEN AID WASHER
Model KHWS01PMT2
Near Waynesville, NC 28786
Kari
Job Details:
07/23/2024
"Took quick pics, found unit showing FDL whenever you try to start a cycle unit ran through diagnostics cycle with no issues. Tried to run a regular cycle and gave door code every time. Took top off and flipped breaker off. Checked continuity on door latch and switch both check good according to the tech sheet. Turned breaker back on and tried to start a cycle. Board just makes a ticking noise. I flicked the top of the control above the door lock resistor and it locked the door and started cycle with no issues. Tried to run drain and spin, heavy duty and another normal cycle and they all locked door and started to fill. Would need board for repair but it is NLA. Had office run cc for TC of $150 and email receipt."
We serviced a
WHIRLPOOL RANGE
Model WEG745H0LZ1
Near Waynesville, NC 28785
Kari
Job Details:
07/23/2024
"Art. 7739553473 Took quick pics, found unit tops works but the bake and broil wont come on, found the regulator opens and lets gas thru to both sides but there is no clicking. Found only 50v going to ignitors from dsi board. Found a resistor blown on dsi. Will need for repair. Gave cust est of $595.80. Customer agreed and paid half of $297.90 today had office email receipt and will owe $297.90 on completion rescheduled for 8/6 PM; ordrng 1 W10860916 (Dsi) and 1 L14 (Jobcode)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ11
Near Spartanburg, SC 29307
Sam
Job Details:
07/23/2024
Found unit still freezing items in refrigerator section. Checked thermistors and fan operations all check ok. Checked damper operation in diagnostics. Damper checks ok. Replaced control. Cycled units power. All functions appear operational and functioning normal. Informed customer to call us back if unit keeps freezing items.
We serviced a
WHIRLPOOL OVEN
Model WOD93EC0AS04
Near Spartanburg, SC 29301
Sam
Job Details:
07/23/2024
"Found unit with f6e1 error code. Explained to customer that since I do not have wall dolly to check unit I would have to go off of best logical guess and the tech sheet which says that control, wire harness and temp sensors can cause issue. Gave customer estimate of 1137.19 for repair with all parts. Customer declined said he will use that money to buy a new one considering units age. Collected trip charge of 150.00."
We serviced a
MAYTAG WASHER
Model MVWX655DW1
Near Boiling Springs, SC 29316
Sam
Job Details:
07/23/2024
Found unit shaking and walking itself around. Found one foot of machine not completely level causing unit to rock back and forth during cycle. Leveled all feet to unit. And calibrated machine using calibrations cycle. Cycled unit through diagnostics cycle and drain and spin. No longer shaking. All functions pass.
We serviced a
WHIRLPOOL DRYER
Model WED4800XQ0
Near Boiling Springs, SC 29316
Sam
Job Details:
07/23/2024
Installed all parts. Unit started heating normally still has good voltage but unit randomly stopped heating found voltage getting lost to heater even while incoming voltage from house checks ok. Will order wire harness.; ordrng 1 W10740200 (Wire harness)
We serviced a
MAYTAG WASHER
Model MVWX655DW1
Near Boiling Springs, SC 29316
Sam
Job Details:
07/23/2024
Found unit shaking and walking itself around. Found one foot of machine not completely level causing unit to rock back and forth during cycle. Leveled all feet to unit. And calibrated machine using calibrations cycle. Cycled unit through diagnostics cycle and drain and spin. No longer shaking. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Chesnee, SC 29323
Sam
Job Details:
07/23/2024
Found units ice maker in freezer not cycling. Found ice blocking units ice maker from rotating and moving arm. Removed ice blocking ice maker from functioning. Cycled unit through diagnostics found no error codes or problems with thermistors or with refrigerator ice maker. Unit defrosting and cooling properly. All functions pass.
We serviced a
AMANA DRYER
Model NED4655EW
Near Gaffney, SC 29340
Sam
Job Details:
07/23/2024
Found units belt split. Used dryer repair kit. Installed new belt and tensioner. Cycled unit through timed dry. Unit rotating drum normally and heating. All functions pass.
We serviced a
WHIRLPOOL MW OVEN COMBO
Model WOEC3030LS00
Near Salem, SC 29676
Frank
Job Details:
07/23/2024
Handle loose.. took off glass tightened screw for handle.. handle now tight..
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS10
Near Taylors, SC 29687
Chris
Job Details:
07/23/2024
Found vent fan installed incorrectly. Installed fan correctly . Unit check is ok . New authorization is w1bsiu0nl2
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Weaverville, NC 28787
Kari
Job Details:
07/22/2024
"Took quick pics, found unit showing 8-1 long fill code. Found cold water packed with sediment installed new valve. Unit checks ok; used 1 W11038689 (Valve) from stock"
We serviced a
WHIRLPOOL RANGE
Model KFGD500ESS11
Near Leicester, NC 28748
Kari
Job Details:
07/22/2024
Robert 7739548471 Safety order number 1538872695 Micheal Found unit was still leaking from regulator. Called techline and spoke with Robert. He advised I replace regulator again and send this one to parts research. I called safety and Micheal is sending part to customer ; ordrng 1 Q16 (Job code) and 1 Waitingoncustomertoreceivepart