We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFF5333PW00
Near Anderson, SC 29626
Frank
Job Details:
11/01/2024
Replaced gaskets heated lubed and formed to door looks like it's sealing ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Boiling Springs, SC 29316
Sam
Job Details:
11/01/2024
Installed parts. Cycled unit through diagnostics cycle. All components working. Unit heats. No leaking found during cycle. All functions pass.
We serviced a
WHIRLPOOL RANGE
Model WEG745H0LZ4
Near Boiling Springs, SC 29316
Sam
Job Details:
11/01/2024
Checked for leak with gas leak detector. Gas leak detector never went off once during checks. No leaks can be located. When going to replace trim handle screws were stripped not allowing handle to come loose and get screws out. Will order handle and screws.; ordrng 1 W11107877 (Handle) and 2 W10917796 (Spacer)s and 2 W10896982 (Screw)s
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Swannanoa, NC 28778
Kari
Job Details:
11/01/2024
"Took quick pics, found house is ripped apart and fridge is in the middle of the floor not plugged in. Took unit compartment cover off and found unit floor covered in dirt and looks like it also got wet. Found compressor windings to check ok but starter clicks and shuts off. Installed new starter and capacitor and plugged unit in. Found the compressor cuts on and the amp drawl is 0.8 amps which is what it should be. I didnt check the evap because the inside of the freezer smells rancid due to the doors being closed and there is a moldy liquid filling the baskets and the floor of the freezer. I unplugged unit and opened doors to prevent further molding. Unit checks ok. ; used 1 W11615506 (Starter), and 1 WPW10350564 (Capacitor) from stock"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHV04
Near Swannanoa, NC 28778
Kari
Job Details:
11/01/2024
Installed parts unit checks ok
We serviced a
WHIRLPOOL M/W OTR
Model WMH32519HZ08
Near Simpsonville, SC 29681
Carl
Job Details:
11/01/2024
Found burnt bulb socket n15; ordrng 1 W11713108 (Harness main) and 1 N15 (Labor)
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ0
Near Simpsonville, SC 29681
Carl
Job Details:
11/01/2024
Cycled unit thru a short cycled could not duplicate issue unit ck ok
We serviced a
KITCHENAID COOKTOP
Model KCED600GBL01
Near Simpsonville, SC 29681
Carl
Job Details:
11/01/2024
Found top cracked l14; ordrng 1 W11051484 (Class top blk) and 1 L14 (Labor)
We serviced a
AMANA DRYER
Model NED4655EW1
Near Liberty, SC 29657
Jerry D.
Job Details:
11/01/2024
Installed parts now all dyer operations normal
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Spartanburg, SC 29307
Sam
Job Details:
11/01/2024
Installed all parts. Cycled unit through quick wash. All components working. All functions pass.
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ2
Near Gaffney, SC 29341
Sam
Job Details:
11/01/2024
Customer fixed water pressure for unit. Cycled unit through calibration mode per whirlpool techline. Cycled unit through overview test cycle. All components working. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ07
Near Greenville, SC 29617
Larry M.
Job Details:
11/01/2024
Customer requested reschedule ;
We serviced a
MAYTAG OVEN
Model MER7700LZ2
Near Gaffney, SC 29341
Sam
Job Details:
11/01/2024
Found unit dead burners working but lights on control not lighting up. Checked voltage. Voltage good at 240. And reaching control and make clicking noises. Unit will need new control. Will order for repair.; ordrng 1 W11548762 (Control) and 1 W11529071 (Main harness) and 1 WPW10245259 (Terminal block) and 1 Preschedule (Preschedule)
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Gaffney, SC 29341
Sam
Job Details:
11/01/2024
Installed parts. Cycled unit through diagnostics cycle. All components activating. No new error codes. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Swannanoa, NC 28778
Kari
Job Details:
11/01/2024
"Took quick pics, found unit left door handle falling off. Found the bottom compression screw stripped and not screwing in. Installed new handle, and gave everything else in the fridge a once over per customer request."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300EWH03
Near Greenville, SC 29615
Chris
Job Details:
11/01/2024
Unit has broken fill cup on imk. Ordeing for repair ; ordrng 1 W10884390 (Imk)
We serviced a
KITCHEN AID REFRIGERATOR
Model KFIS29BBMS00
Near Greer, SC 29651
Chris
Job Details:
11/01/2024
Unit is 26 in freezer and 51 in fresh food.all fans activate in test 3. Condenser coils are clear. No Heat on mullion. E5 in test 56. Unit has sealed system failure . Customer denied repair
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Spartanburg, SC 29306
Sam
Job Details:
11/01/2024
Installed actuator. Cycled unit through diagnostic cycle and quick wash. All components working. All functions pass.
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Asheville, NC 28803
Brian
Job Details:
11/01/2024
"Installed new spin basket. Calibrated and tested unit observing for leaks and proper functions. At this time, all operations ok with no leak detected."
We serviced a
WHIRLPOOL WASHER
Model WTW7000DW4
Near Simpsonville, SC 29681
Carl
Job Details:
11/01/2024
Ran diagnostics found bad valve installed new valve ran a test cycle unit ck ok
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Asheville, NC 28803
Brian
Job Details:
11/01/2024
Found no saved error codes. Found suspension bad. Tested unit in diagnostics and found belt and cam squealing. Belt (W11239857) pulley (w10721967) and suspension (W11130362)needed. ; ordrng 1 W11239857 (Belt) and 1 w10721967 (Pulley) and 1 W11130362 (Suspension) and 1 L14 (Job code)
We serviced a
MAYTAG WASHER
Model MVW6500MBK0
Near Fairview, NC 28730
Brian
Job Details:
11/01/2024
Found no saved error codes. Tested unit and found spin basket wobbling in spin cycle. Found gearcase warped. Gearcase (W11449840) cam (W10721967) and belt (WPW10006384) needed. ; ordrng 1 W11449840 (Gearcase) and 1 W10721967 (Cam) and 1 WPW10006384 (Belt) and 1 Q16 (Job code)
We serviced a
KITCHENAID RANGE
Model KFDC506JSS01
Near Fairview, NC 28730
Brian
Job Details:
11/01/2024
Installed parts ordered. Tested and found all operations ok at this time.
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Fairview, NC 28730
Brian
Job Details:
11/01/2024
"Found no saved error codes. Tested unit in diagnostics and unit filled and drained. Lid lock attempted to lock multiple times and could not. New lid lock (W11670519) needed.quoted customer 374.22. Informed customer that there could always be further issues resulting in further repairs being needed, but that we will have to start with lid latch before further diagnostics can be made. Customer understood and wishes to proceed with repairs. Collected total. ; ordrng 1 W11670519 (Lid lock) and 1 J13 (Job code)"
We serviced a
WHIRLPOOL OVEN
Model WOS51EC0AS02
Near Fairview, NC 28730
Brian
Job Details:
11/01/2024
Found unit non responsive and no display. Checked and found thermal fuse behind ui bad. Installed new Thermal fuse (WPW10545255) and tested. Found all operations ok at this time. ; used 1 WPW10545255 (Thermal fuse TS) from stock
We serviced a
KITCHENAID ICE MACHINE
Model KUIX335HPS01
Near Greenville, SC 29607
Carl
Job Details:
11/01/2024
Pump receiving voltage and bad water valve l14; ordrng 1 W11542867 (Pump) and 1 W10897719 (Valve)
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Greenville, SC 29609
Carl
Job Details:
11/01/2024
Installed new control ran diagnostics and a test cycle unit ck ok no errors
We serviced a
WHIRLPOOL FREEZER
Model WRS571CIHZ04
Near Easley, SC 29640
Larry M.
Job Details:
11/01/2024
Found evap motor making taping sound p. Replaced evap motor. Will need fan blade. Found freezer door making a creeking noise. Will need freezer door ; ordrng 1 W11561286 (Door) and 1 2manjobcode (2 man job code) and 1 WP2169142 (Fan)
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW
Near Easley, SC 29642
Larry M.
Job Details:
11/01/2024
Found pump running continuously. Unplugged pressure hose. Pump still ran continuously. Will need main control.; ordrng 1 J13jobcode (J13 job code) and 1 W11124783 (Main control)
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW1
Near Powdersville, SC 29673
Larry M.
Job Details:
11/01/2024
Found unit adding water for longer than normal. Will need main control and pressure valve.; ordrng 1 L14jobcode (L14 job code) and 1 W11316246 (Pressure switch)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRV976FDEM
Near Pelzer, SC 29669
Jerry D.
Job Details:
11/01/2024
Inastalled new drier and process tube pulled vacuum and recherged ref cooling normal. Customer toled me about lights out in food section will order parts (by JR)
We serviced a
WHIRLPOOL DRYER
Model WED6150PW0
Near Greenville, SC 29611
Larry M.
Job Details:
11/01/2024
Found drum out of balance and making a thumping sound. Will need inner drum. ; ordrng 1 W10899578 (Drum)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ18
Near Duncan, SC 29334
Chris
Job Details:
11/01/2024
Cusotmer has damaged filter causing odd water circulation noises in unit . Tip is broken off filter and is visibly damaged. When filter is removed or pressure applied to filter noise goes away. Left filter out of unit due to possible failure that could cause water damage. advised customer to contact customer service since unit was delivered with damaged filter
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS335SDHM06
Near Duncan, SC 29334
Chris
Job Details:
11/01/2024
Imk failed during harvest. Replaced from stock. Unit check is ok. Called trade care for extra labor authorization for 2nd trip. New labor authorization is w1cmpi0nl2
We serviced a
JENN-AIR OVEN
Model JMW2427DB01
Near Lyman, SC 29365
Chris
Job Details:
11/01/2024
Installed new panel. Unit check is ok . authorization is j1cmp40xpl2
We serviced a
KITCHEN AID MICROWAVE
Model KMHC319EBS2
Near Greer, SC 29651
Chris
Job Details:
11/01/2024
Installed new parts. Unit check is ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Greenville, SC 29617
Larry M.
Job Details:
11/01/2024
Installed mullin and door. Found there was still a gap in cabinet and door. Will need foam and thicker gasket; ordrng 1 W10407216 (Freezer gasket) and 1 W11159728 (Foam) and 1 J13jobcode (J13 job code)
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS3
Near Taylors, SC 29687
Chris
Job Details:
11/01/2024
Installed new parts. Unit check is ok
We serviced a
WHIRLPOOL WASHER/DRYER COM
Model WFC682CLW0
Near Greenville, SC 29611
Larry M.
Job Details:
11/01/2024
Found f9e1 fault code. Checked drain. Found blockage in drain. Installed pump and rain test cycle. Same error code came back. Will need main control. ; ordrng 1 W11535124 (Ui) and 1 J13jobcode (J 13 job code)
We serviced a
WHIRLPOOL LAUNDRY CENTER
Model WTW5010LW0
Near Seneca, SC 29678
Frank
Job Details:
11/01/2024
Wire harness broke to drain tried to repair.. drained water out of unit.. need wire harness.; ordrng 1 W11643701 (Wire harness) and 1 Jobcodej13 (Job code j13)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFF5333PW00
Near Anderson, SC 29626
Frank
Job Details:
11/01/2024
Replaced gaskets heated lubed and formed to door looks like it's sealing ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Boiling Springs, SC 29316
Sam
Job Details:
11/01/2024
Installed parts. Cycled unit through diagnostics cycle. All components working. Unit heats. No leaking found during cycle. All functions pass.
We serviced a
WHIRLPOOL RANGE
Model WEG745H0LZ4
Near Boiling Springs, SC 29316
Sam
Job Details:
11/01/2024
Checked for leak with gas leak detector. Gas leak detector never went off once during checks. No leaks can be located. When going to replace trim handle screws were stripped not allowing handle to come loose and get screws out. Will order handle and screws.; ordrng 1 W11107877 (Handle) and 2 W10917796 (Spacer)s and 2 W10896982 (Screw)s
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Swannanoa, NC 28778
Kari
Job Details:
11/01/2024
"Took quick pics, found house is ripped apart and fridge is in the middle of the floor not plugged in. Took unit compartment cover off and found unit floor covered in dirt and looks like it also got wet. Found compressor windings to check ok but starter clicks and shuts off. Installed new starter and capacitor and plugged unit in. Found the compressor cuts on and the amp drawl is 0.8 amps which is what it should be. I didnt check the evap because the inside of the freezer smells rancid due to the doors being closed and there is a moldy liquid filling the baskets and the floor of the freezer. I unplugged unit and opened doors to prevent further molding. Unit checks ok. ; used 1 W11615506 (Starter), and 1 WPW10350564 (Capacitor) from stock"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHV04
Near Swannanoa, NC 28778
Kari
Job Details:
11/01/2024
Installed parts unit checks ok
We serviced a
WHIRLPOOL M/W OTR
Model WMH32519HZ08
Near Simpsonville, SC 29681
Carl
Job Details:
11/01/2024
Found burnt bulb socket n15; ordrng 1 W11713108 (Harness main) and 1 N15 (Labor)
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ0
Near Simpsonville, SC 29681
Carl
Job Details:
11/01/2024
Cycled unit thru a short cycled could not duplicate issue unit ck ok
We serviced a
KITCHENAID COOKTOP
Model KCED600GBL01
Near Simpsonville, SC 29681
Carl
Job Details:
11/01/2024
Found top cracked l14; ordrng 1 W11051484 (Class top blk) and 1 L14 (Labor)
We serviced a
AMANA DRYER
Model NED4655EW1
Near Liberty, SC 29657
Jerry D.
Job Details:
11/01/2024
Installed parts now all dyer operations normal
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Spartanburg, SC 29307
Sam
Job Details:
11/01/2024
Installed all parts. Cycled unit through quick wash. All components working. All functions pass.
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ2
Near Gaffney, SC 29341
Sam
Job Details:
11/01/2024
Customer fixed water pressure for unit. Cycled unit through calibration mode per whirlpool techline. Cycled unit through overview test cycle. All components working. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ07
Near Greenville, SC 29617
Larry M.
Job Details:
11/01/2024
Customer requested reschedule ;
We serviced a
MAYTAG OVEN
Model MER7700LZ2
Near Gaffney, SC 29341
Sam
Job Details:
11/01/2024
Found unit dead burners working but lights on control not lighting up. Checked voltage. Voltage good at 240. And reaching control and make clicking noises. Unit will need new control. Will order for repair.; ordrng 1 W11548762 (Control) and 1 W11529071 (Main harness) and 1 WPW10245259 (Terminal block) and 1 Preschedule (Preschedule)
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Gaffney, SC 29341
Sam
Job Details:
11/01/2024
Installed parts. Cycled unit through diagnostics cycle. All components activating. No new error codes. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Swannanoa, NC 28778
Kari
Job Details:
11/01/2024
"Took quick pics, found unit left door handle falling off. Found the bottom compression screw stripped and not screwing in. Installed new handle, and gave everything else in the fridge a once over per customer request."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300EWH03
Near Greenville, SC 29615
Chris
Job Details:
11/01/2024
Unit has broken fill cup on imk. Ordeing for repair ; ordrng 1 W10884390 (Imk)
We serviced a
KITCHEN AID REFRIGERATOR
Model KFIS29BBMS00
Near Greer, SC 29651
Chris
Job Details:
11/01/2024
Unit is 26 in freezer and 51 in fresh food.all fans activate in test 3. Condenser coils are clear. No Heat on mullion. E5 in test 56. Unit has sealed system failure . Customer denied repair
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Spartanburg, SC 29306
Sam
Job Details:
11/01/2024
Installed actuator. Cycled unit through diagnostic cycle and quick wash. All components working. All functions pass.
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Asheville, NC 28803
Brian
Job Details:
11/01/2024
"Installed new spin basket. Calibrated and tested unit observing for leaks and proper functions. At this time, all operations ok with no leak detected."
We serviced a
WHIRLPOOL WASHER
Model WTW7000DW4
Near Simpsonville, SC 29681
Carl
Job Details:
11/01/2024
Ran diagnostics found bad valve installed new valve ran a test cycle unit ck ok
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Asheville, NC 28803
Brian
Job Details:
11/01/2024
Found no saved error codes. Found suspension bad. Tested unit in diagnostics and found belt and cam squealing. Belt (W11239857) pulley (w10721967) and suspension (W11130362)needed. ; ordrng 1 W11239857 (Belt) and 1 w10721967 (Pulley) and 1 W11130362 (Suspension) and 1 L14 (Job code)
We serviced a
MAYTAG WASHER
Model MVW6500MBK0
Near Fairview, NC 28730
Brian
Job Details:
11/01/2024
Found no saved error codes. Tested unit and found spin basket wobbling in spin cycle. Found gearcase warped. Gearcase (W11449840) cam (W10721967) and belt (WPW10006384) needed. ; ordrng 1 W11449840 (Gearcase) and 1 W10721967 (Cam) and 1 WPW10006384 (Belt) and 1 Q16 (Job code)
We serviced a
KITCHENAID RANGE
Model KFDC506JSS01
Near Fairview, NC 28730
Brian
Job Details:
11/01/2024
Installed parts ordered. Tested and found all operations ok at this time.
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Fairview, NC 28730
Brian
Job Details:
11/01/2024
"Found no saved error codes. Tested unit in diagnostics and unit filled and drained. Lid lock attempted to lock multiple times and could not. New lid lock (W11670519) needed.quoted customer 374.22. Informed customer that there could always be further issues resulting in further repairs being needed, but that we will have to start with lid latch before further diagnostics can be made. Customer understood and wishes to proceed with repairs. Collected total. ; ordrng 1 W11670519 (Lid lock) and 1 J13 (Job code)"
We serviced a
WHIRLPOOL OVEN
Model WOS51EC0AS02
Near Fairview, NC 28730
Brian
Job Details:
11/01/2024
Found unit non responsive and no display. Checked and found thermal fuse behind ui bad. Installed new Thermal fuse (WPW10545255) and tested. Found all operations ok at this time. ; used 1 WPW10545255 (Thermal fuse TS) from stock
We serviced a
KITCHENAID ICE MACHINE
Model KUIX335HPS01
Near Greenville, SC 29607
Carl
Job Details:
11/01/2024
Pump receiving voltage and bad water valve l14; ordrng 1 W11542867 (Pump) and 1 W10897719 (Valve)
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Greenville, SC 29609
Carl
Job Details:
11/01/2024
Installed new control ran diagnostics and a test cycle unit ck ok no errors
We serviced a
WHIRLPOOL FREEZER
Model WRS571CIHZ04
Near Easley, SC 29640
Larry M.
Job Details:
11/01/2024
Found evap motor making taping sound p. Replaced evap motor. Will need fan blade. Found freezer door making a creeking noise. Will need freezer door ; ordrng 1 W11561286 (Door) and 1 2manjobcode (2 man job code) and 1 WP2169142 (Fan)
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW
Near Easley, SC 29642
Larry M.
Job Details:
11/01/2024
Found pump running continuously. Unplugged pressure hose. Pump still ran continuously. Will need main control.; ordrng 1 J13jobcode (J13 job code) and 1 W11124783 (Main control)
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW1
Near Powdersville, SC 29673
Larry M.
Job Details:
11/01/2024
Found unit adding water for longer than normal. Will need main control and pressure valve.; ordrng 1 L14jobcode (L14 job code) and 1 W11316246 (Pressure switch)
We serviced a
WHIRLPOOL COOKTOP
Model W5CE3024XB00
Near Spartanburg, SC 29307
Sam
Job Details:
10/31/2024
Installed cooktop glass. Cycled all burners. All burners working. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ18
Near Donalds, SC 29638
Jerry D.
Job Details:
10/31/2024
INSTALLED NEW AUGER MOTOR NOW DISPENSING ICE NORMALLY
We serviced a
AMANA DRYER
Model NED4655EW1
Near Greenwood, SC 29649
Jerry D.
Job Details:
10/31/2024
INSTALLED NEW DRUM AND REPAIR KIT NOW DRYER RUNNING AT NORMAL SOUND LEVELS
We serviced a
WHIRLPOOL WASHER
Model MVW4505MW1
Near Easley, SC 29640
Carl
Job Details:
10/31/2024
Received tub damaged ; ordrng 1 W11219115 (Outter tub)
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Greenwood, SC 29646
Jerry D.
Job Details:
10/31/2024
found dishwasher filling and draining but was motor never running. has power to wash motor replaced part now all functions normal
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Greer, SC 29650
Chris
Job Details:
10/31/2024
Unit has defective ui. Replaced ui. Unit check is ok ; used 1 W11622490 (Console) from stock
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Greenwood, SC 29646
Jerry D.
Job Details:
10/31/2024
checked washer through normal cycle found washer making noise in wash cycle found penny under wash plate removes also checked stuts splutch and belt all funtions normal
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPM2
Near Greer, SC 29650
Chris
Job Details:
10/31/2024
Customer states unit will not finish cycle after power outage . standing water in unit upon arrival . Drained water. Unit completely drained. Unit has 4-3 and 7-1 faults . Ran service cycle and calibrated . Unit performs as designed. Ran normal cycle and unit completed as designed by via phone with customer confirming. Unit check is ok
We serviced a
MAYTAG WASHER
Model MVWC465HW4
Near Greer, SC 29651
Chris
Job Details:
10/31/2024
"Unit has worn cam gears and loose shifter. Slight oil from capacitor. Replaced parts. Unit check is ok; used 1 W10913953 (Shifter), and 1 W10721967 (Cam) from stock"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS335SDHM07
Near Greer, SC 29651
Chris
Job Details:
10/31/2024
Unit is brand new out the box. Compressor will not come on. Inverter light will not coming on. No loose connections. Builder states he has 14 day return policy with his vendor/dealer and will take unit back
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Duncan, SC 29334
Chris
Job Details:
10/31/2024
Installed new parts. Unit running makes loud screaming noise from drive train. Replaced parts from stock. Unit check is ok . New labor authorization is m1cm7y0nl1.5; used 1 W11449840 (Gearcase) from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ03
Near Flat Rock, NC 28731
Brian
Job Details:
10/31/2024
"Unit unplugged when I arrived. Plugged unit in and found compressor attempting to start then shutting off. Inspected compressor compartment and found evidence roaches all over compressor compartment, damaging main control and possibly all other components in compressor compartment. At least Control (W11035836) start device (W11561262) and capacitor (WPW10662129) will be needed. Contacted partner team and spoke to Tianna. She documented and said that we cannot work on unit until the bug problem is resolved. Informed customer and informed them that if they have any questions they can call whirlpool customer service, customer understood. File number (7740121633)"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706ESS05
Near Hendersonville, NC 28792
Brian
Job Details:
10/31/2024
Found temps ok in unit when I arrived. Found no ice maker error codes. Test cycled ice maker and found it completing cycle and filling properly. Contacted tech support and spoke to Andrew. I informed him of all previous work done on unit. He said no more repairs are can be done for issue at this time. Unit is non repairable. Informed customer of situation and recommended they contact customer service if they have any questions. Sr number (7739761277)
We serviced a
WHIRLPOOL WASHER
Model MVW4505MW0
Near Hendersonville, NC 28739
Brian
Job Details:
10/31/2024
"Found f7e1 (tachometer missing) f7e6 (motor circuit open). Tested unit and when it began spin cycle, it cancelled diagnostics and gave motor error code again. Inspected and found wire harness damaged. Also tested motor and found one of the windings out of range. Main control (W11626074) shifter (W11481722) Lower harness (W11643701) motor (W11026785) and clip (W11755726) needed. ; ordrng 1 W11026785 (Motor) and 1 W11643701 (Lower harness) and 1 W11481722 (Shifter) and 1 W11626074 (Control) and 1 W11755726 (Clip) and 1 L14 (Job code)"
We serviced a
AMANA DISHWASHER
Model ADB1400AMS1
Near Mills River, NC 28759
Brian
Job Details:
10/31/2024
"Installed main control and dispenser. Tested unit in diagnostics and found all operations ok at this time, with no leaks detected. Did not move unit."
We serviced a
WHIRLPOOL REFRIGERATOR
Model ED5JHGXRB02
Near Fletcher, NC 28732
Brian
Job Details:
10/31/2024
"Installed new ice maker and tested, observing for leaks and proper functions. At this time, all operations ok with no leaks detected."
We serviced a
WHIRLPOOL DRYER
Model WED8127LW2
Near Fletcher, NC 28732
Brian
Job Details:
10/31/2024
Found moisture sensors not passing in diagnostics and found lent screen housing not installed correctly. Inspected and found moisture sensor unplugged and a couple screws missing from screen housing. Inspected all parts and found nothing damaged. Installed new screws and connected moisture sensor. Tested and found all operations ok at this time.
We serviced a
WHIRLPOOL DRYER
Model WED5605MW0
Near Arden, NC 28704
Brian
Job Details:
10/31/2024
Found some buttons on user interface not responding at times. Found no saved error codes and all connections ok. Console (W11583883) control (W11733951) harness (W11459337) name plate (W11223753); ordrng 1 W11583883 (Console) and 1 W11733951 (Control) and 1 W11459337 (Harness) and 1 W11223753 (Name plate) and 1 S17 (Job code)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Taylors, SC 29687
Carl
Job Details:
10/31/2024
Removed old compressor an evap installed new evap compressor and filter installed r600 cycled unit on is pulling down in temp ck ok
We serviced a
WHIRLPOOL DRYER
Model WED7500VW2
Near Honea Path, SC 29654
Frank
Job Details:
10/31/2024
Replaced timer.. not heating on timed dry.. heating ok on normal automatic dry. Sr7740231015. Heat doesn't come on for 20 min in timed dry it is for light garments. Unit operating as intended
We serviced a
WHIRLPOOL RANGE
Model WFE535S0LZ3
Near Honea Path, SC 29654
Frank
Job Details:
10/31/2024
Replaced control board.. tested baking and broil.. heating ok. Functions good
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Greenville, SC 29611
Carl
Job Details:
10/31/2024
Outter tub damaged n15; ordrng 1 W10371566 (Outter tub) and 1 N15 (Labor)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ09
Near Simpsonville, SC 29680
Carl
Job Details:
10/31/2024
Found pin pushed out in imk harness adjusted tab reinstalled pins cycled imk ck ok
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS3
Near Simpsonville, SC 29680
Carl
Job Details:
10/31/2024
Ran diagnostics and did the service pointer for the vent leak ck ok
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS10
Near Powdersville, SC 29673
Carl
Job Details:
10/31/2024
Found hi side and diode open and mag tube magnet cracked n15; ordrng 1 W11545871 (Transformer) and 1 W11495561 (Mag tube) and 1 W11256462 (Diode) and 1 N15 (Labor)
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Duncan, SC 29334
Chris
Job Details:
10/31/2024
"Outlet is repaired. Once control was installed unit needs a variety of parts. Installed new parts. Unit check is ok. New authorization is a1cm3i0al2; used 1 W10919003 (Pump), 1 W11454741 (Gearcase), and 1 W11210463 (Valve) from stock"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ06
Near Anderson, SC 29621
Frank
Job Details:
10/31/2024
Replaced valve.. reset ice maker.. tested fill. Manually filling ok.. there was some ice build up inside freezer.. Techline suggest replacing freezer door.. if problem persists order door and if ice maker not making ice maybe replace control board
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ06
Near Liberty, SC 29657
Frank
Job Details:
10/31/2024
Installed listed parts working dispensing ice ok. Put some more foam tape around chute opening maybe air is coming in through that point.
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Cowpens, SC 29330
Sam
Job Details:
10/31/2024
Installed parts. Cycled unit in timed dry. Unit heating much more often cycling on and off properly. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Spartanburg, SC 29301
Sam
Job Details:
10/31/2024
Upon arrival unit has not been cooling. Plugged unit in. All lights thermistors and fans coming on and operating. Units compressor never kicked on. All signs point to bad inverter box never powering compressor on. Will order inverter box for repair.; ordrng 1 W11567494 (Inverter box)