We serviced a
WHIRLPOOL COOKTOP
Model WFES3030RW0
Near Swannanoa, NC 28778
Kari
Job Details:
03/28/2025
"Took quick pics, found LF burner would only stay on high. Installed new switch, element now cycles. Unit checks ok; used 1 W10857622 (Switch) from stock"
We serviced a
JENN-AIR MICROWAVE
Model JMW3430DS01
Near Walhalla, SC 29691
Frank
Job Details:
03/28/2025
Replaced customer supplied console. Put in tested working as intended collecting$175 labor
We serviced a
WHIRLPOOL FREEZER
Model WRS588FIHZ06
Near Boiling Springs, SC 29316
Sam
Job Details:
03/28/2025
Turned data loggers on and out one in each compartment on middle shelf of unit. Will return in 1-2 weeks to return for data loggers.; O-emld tckt
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ07
Near Spartanburg, SC 29307
Matt
Job Details:
03/28/2025
Evacuated system. Replaced compressor and drier filter. Pressure tested. Unit held pressure. Pulled a vacuum and unit held vacuum. Worked in 1.87 ounces of r600a. Checks ok
We serviced a
WHIRLPOOL DRYER
Model WED4850HW0
Near Etowah, NC 28729
Brian
Job Details:
03/28/2025
Installed new start switch and door seal. Tested and found all operations ok at this time.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ06
Near Etowah, NC 28729
Brian
Job Details:
03/28/2025
"When I arrived, customer informed me that unit is no longer cooling properly. Inspected and found freezer evaporator now frozen over. Tested and found heater coming on. New thermostat(W11724692)and Control (W11595219) needed. Installed all other parts. ; ordrng 1 W11724692 (Thermostat) and 1 W11595219 (Control) and 1 U18 (Job code)"
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HZ09
Near Greenville, SC 29611
Nathan
Job Details:
03/28/2025
"Needs magnetron,diode,and high voltage transformer for not heating correctly. Making loud noise from xmfr and not heating cup of water tested at two minutes. Office will call and schedule return visit when parts arrive. ; ordrng 1 W11737891 (Magnetron) and 1 W11737892 (High voltage xmfr) and 1 W11256462 (Diode) and 1 N15laborcode (N15 labor code)"
We serviced a
WHIRLPOOL WASHER/DRYER COM
Model WET4024HW0
Near Greenville, SC 29615
Nathan
Job Details:
03/28/2025
Pulled out washer and locked down leveling feet. When spinning it gave an e4 error code. Had to clear out code for washer to work. Put in some towels and let washer soak them. Then put on drain and spin and washers working fine now. Performing as designed.
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Taylors, SC 29687
Chris
Job Details:
03/28/2025
"Unit has loud drive train noise . Replaced parts from stock. Unit check is ok . New authorization is m1dqr80nl1.5; used 1 W10006384 (Belt), 1 W10721987 (Cam), and 1 W11449840 (Gearcase) from stock"
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Greer, SC 29651
Chris
Job Details:
03/28/2025
Unit has broken hinges. Ordeing for repair ; ordrng 2 W11551301 (Hinge)s
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ2
Near Greer, SC 29651
Chris
Job Details:
03/28/2025
Found shorted wash motor. Replaced from stock Unit check is ok
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Greenville, SC 29611
Larry M.
Job Details:
03/28/2025
Found drain pump running continuously. Will need main control. ; ordrng 1 J13jobcode (J13 job code) and 1 W11607637 (Main control)
We serviced a
KITCHENAID COMPACTOR
Model KTTS505ESS0
Near Simpsonville, SC 29681
Carl
Job Details:
03/28/2025
Installed new pedal and spring
We serviced a
JENN-AIR OVEN
Model JJW3830DS02
Near Fountain Inn, SC 29644
Jerry D.
Job Details:
03/28/2025
"F2 code for control panel, customer has been resetting breaker for approximately 3 months and that would fix it, now reset isnt working, customer has been working with whirlpool to get help, cancelled for now"
We serviced a
KITCHENAID MICROWAVE/HOOD
Model KOEC530PSS01
Near Simpsonville, SC 29681
Carl
Job Details:
03/28/2025
Found roller ring noisey. ; ordrng 1 W11110134 (Ring roller)
We serviced a
MAYTAG WASHER
Model MVWB835DC
Near Simpsonville, SC 29680
Carl
Job Details:
03/28/2025
Installed new dispenser housing ran diagnostics and a test cycle to ck operation unit ck ok
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Simpsonville, SC 29680
Jerry D.
Job Details:
03/28/2025
"Found touchpad unresponsive found loose wire connector on cntrl , reinstalled all connections, unit chks ok, customer is fixing cord"
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS10
Near Simpsonville, SC 29680
Carl
Job Details:
03/28/2025
Installed new acu cycled unit ck ok
We serviced a
WHIRLPOOL KITCHEN
Model WDP540HAMZ4
Near Fountain Inn, SC 29644
Carl
Job Details:
03/28/2025
Installed new acu and sensor ran diagnostics found wash pump I now receiving voltage and ohm good is not running ; ordrng 1 W11613479 (Sump assembly)
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Fountain Inn, SC 29644
Carl
Job Details:
03/28/2025
Installed new acu ran diagnostics and a test cycle to check operation unit ck ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHB09
Near Mauldin, SC 29662
Jerry D.
Job Details:
03/28/2025
"Temps 36@1, Not enough water to refrigerator or imk, Customer wants regulator removed, removed regulator and cycled imk fill now ok, and dispenser, no leaks found, water now chks ok"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ1
Near Simpsonville, SC 29681
Jerry D.
Job Details:
03/28/2025
"Motor humming , ordering, j13; ordrng 1 W11197948 (Motor and sump)"
We serviced a
WHIRLPOOL OVEN
Model WFES3330RZ0
Near Easley, SC 29642
Larry M.
Job Details:
03/28/2025
Incorrect hinges came in the box. Will need to order correct ones. Customer would like unit replaced. ; ordrng 2 WPW10299225 (Hinge)s
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW06
Near Easley, SC 29642
Larry M.
Job Details:
03/28/2025
Recorded fridge temps. 37 in the refrigerator 0 in the freezer. Adjusted setting. All functions pass.
We serviced a
JENN-AIR DISHWASHER
Model JDPSS244LM2
Near Taylors, SC 29687
Chris
Job Details:
03/28/2025
Installed new part. Unit check is ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRB322DMBW05
Near Greer, SC 29650
Chris
Job Details:
03/28/2025
Found worn harness. Ordeing for repair ; ordrng 1 W11741475 (Harness)
We serviced a
JENN AIR WALL OVEN
Model JJW3430HS00
Near Black Mountain, NC 28711
Kari
Job Details:
03/28/2025
"Took quick pics, found unit had an 2-1 stuck button key stored in memory cleared codes and ran bake cycle to 350. Preheat completed and no repeat errors, put unit into diagnostics and reset control, when unit was finished resetting I recalibrated the screen touch. Gave cust est of $1,715.62. Customer declined repair at this time since unit is working and will call back if they want to replace user interface. Had office run cc for $150 TC and email receipt. I didnt uninstall unit."
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Salem, SC 29676
Frank
Job Details:
03/28/2025
Unit keeps going onto drain mode. Need to replace board.; ordrng 1 W11608056 (Control) and 1 Jobcodej13 (Job code j13)
We serviced a
KITCHENAID MW OVEN COMBO
Model KOEC530PSS01
Near Piedmont, SC 29673
Larry M.
Job Details:
03/28/2025
Found ding in door. Will need door. ; ordrng 1 W11600216 (Door) and 1 J13jobcode (J13 job code)
We serviced a
MAYTAG WASHER
Model MVWB765FW4
Near Piedmont, SC 29673
Larry M.
Job Details:
03/28/2025
Found main control not sensing what cycle it was put in. Quoted customer 634.92 to replace board. Customer declined.
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Inman, SC 29349
Chris
Job Details:
03/28/2025
Unit will die mid cycle and will have to wait for unit to cool down before it can be re started. Vents are clear and Cusotmer has strong air flow. Ordering parts for repair ; ordrng 1 WP694089 (Wheel) and 1 279827 (Motor) and 1 N15 and 1 Anytech and 1 Anytech
We serviced a
WHIRLPOOL OVEN
Model WOD51EC0HS20
Near Fountain Inn, SC 29644
Jerry D.
Job Details:
03/28/2025
Customer says Cntrl panel inoperable she is working with whirlpool to get it coverd cancelled for now
We serviced a
KITCHEN AID DISHWASHER
Model KDFE104DSS5
Near Columbus, NC 28722
Brian
Job Details:
03/26/2025
"Installed upper and lower spray arms. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Union, SC 29379
Sam
Job Details:
03/26/2025
Installed ice maker. Cycled harvest and filled with water. Units ice maker performed all actions perfectly. All functions pass.
We serviced a
MAYTAG DRYER
Model MED8630HC1
Near Simpsonville, SC 29680
Jerry D.
Job Details:
03/26/2025
"Motor and blower broken , blower stuck on motor, installed parts listed sent preid, cycled unit through test and all functions are working properly ; O-emld tckt"
We serviced a
MAYTAG DRYER
Model MED6230HW1
Near Pelzer, SC 29669
Jerry D.
Job Details:
03/26/2025
"Found heater open thermostat overheated warped and bent, installed listed parts sent preid, cycled unit through test and all functions are working properly"
We serviced a
KITCHEN AID DISHWASHER
Model KUDS01ILWH1
Near Greer, SC 29650
Chris
Job Details:
03/26/2025
Unit has dry rotted door gasket. Gave customer a bluebook estimate for repair at $424.95. Installed new gasket.Unit will not power on . Fuse shows continuity. No labeled breakers in home . Called tech line and spoke with garret.unit has break in wire harness. No voltage to control but voltage at terminal block . Unit needs wire harness . Part unavailable. File number for call is 7741219219
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDW11
Near Pickens, SC 29671
Matt
Job Details:
03/26/2025
Evacuated system replaced compressor and evaporator. Pressure tested. Unit held pressure. Pulled a vacuum. Unit held vacuum. Weighed in 1.76 oncues r600aAuthorization w1dpv91nl1.5; used 1 W11506635 (Coupler) from stock
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF507HBS00
Near Boiling Springs, SC 29316
Sam
Job Details:
03/26/2025
Unit has 1 light out in freezer section and 1 light out in refrigerator section. Will order light service kit. Cannot tell if light out in freezer is because of light itself or switch. Will order switch just in case for repair. ; ordrng 1 W11683244 (Led kit) and 1 W11396033 (Switch) and 1 L14 (L14)
We serviced a
WHIRLPOOL M/W OTR
Model WMMF7330RZ00
Near Inman, SC 29349
Chris
Job Details:
03/26/2025
Unit has scratched door and cover. Ordeing for repair ; ordrng 1 W11662375 (Vent) and 1 W11731160 (Door) and 1 Anytech and 1 Anytech and 1 Anytech and 1 Anytech
We serviced a
JENN-AIR RANGE
Model JDS1750FP0
Near Greenville, SC 29615
Chris
Job Details:
03/26/2025
Installed new part. Unit check is ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW01
Near Taylors, SC 29687
Nathan
Job Details:
03/26/2025
"Replaced evaporator,compressor,and filter drier. Evaporator was leaking. Pressurized at 250 psi for 15 minutes then vacuumed for 30 minutes until vacuum reached 500 microns. Added 4.24 ounces of R134a refrigerant to system. Everythings performing as designed. Let homeowner know itll take 24 hours to get back to correct temperatures. Has 5 year parts and labor on the sealed system so owner doesnt owe anything towards repair."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ06
Near Lyman, SC 29365
Chris
Job Details:
03/26/2025
Installed new part. Unit Check is ok
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW1
Near Pendleton, SC 29670
Frank
Job Details:
03/26/2025
Replaced listed parts tested cycle working as designed
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHB
Near Easley, SC 29640
Larry M.
Job Details:
03/26/2025
Found bottom freezer at appropriate temperature 0. Found refrigerator not cooling. Found damper stuck closed. Will need damper. ; ordrng 1 W11087463 (Damper) and 1 J13jobcode (J13 job code)
We serviced a
KITCHEN AID MICROWAVE
Model KOCE500ESS22
Near Piedmont, SC 29673
Larry M.
Job Details:
03/26/2025
Could not get unit to come out of wall. Informed customer that unit will need to be removed before we can fix unit. ;
We serviced a
KITCHENAID KITCHEN
Model KDTM404KPS3
Near Piedmont, SC 29673
Larry M.
Job Details:
03/26/2025
Found motor not working when put into diagnostics. Will need motor. ; ordrng 1 W11416362 (Pump assembly) and 1 N14jobcode (N14 job code)
We serviced a
WHIRLPOOL WASHER
Model WTW4850HW1
Near Easley, SC 29642
Larry M.
Job Details:
03/26/2025
"Found gearcase loose. Found grease leaking. Quoted customer $725.60 to replace gearcase, belt and splutch kit. Customer declined"
We serviced a
KITCHEN AID REFRIGERATOR
Model n/a
Near Travelers Rest, SC 29690
Matt
Job Details:
03/26/2025
Found some LED modules have failed and lights are flickering. This unit is over 5 years old and doesn't qualify for service pointer w11460554. Rev n. Blue book estimate to install new LED module kit is 554.00. I have customer the customer care number to see if they could get a concession for this repair. 1-800-253-1301If customer calls back and wants parts ordered part number is W11683244. If customer calls back in less than 30 days balance would be 404.00
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Travelers Rest, SC 29690
Matt
Job Details:
03/26/2025
Customer said unit does not heat. Found no power on the red wire from the motor. Checked motor and found the main harness not snapped into place on the lower side of the motor. Snapped harness into place and pulled on it to make sure it could not come loose. Harness is secure. Tested operation. Dryer now heats properly.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT549SZDM06
Near Spartanburg, SC 29301
Sam
Job Details:
03/26/2025
Unit not making ice. Found unit not filling with water. Cycled ice maker. Ice maker rotated. Did not hear humming from valve when energized to fill with water. Replaced valve from ice maker kit pre ID. Cycled ice maker again. Ice maker rotating and now filling with water. No leaks found during test. All components working. All functions pass.
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Pendleton, SC 29670
Frank
Job Details:
03/26/2025
Roller seized in unit making squeaky sound. Put in dryer repair kit tested working as intended
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Lyman, SC 29365
Chris
Job Details:
03/26/2025
Unit has failed pressure sensor. Ordeing for repair ; ordrng 1 W11607637 (Control)
We serviced a
MAYTAG WASHER
Model MVWX655DW2
Near Spartanburg, SC 29301
Sam
Job Details:
03/26/2025
Found unit not dispensing fabric softener. Unit also appears to be making slight squeaking noise when agitating. Unit has no error codes in diagnostics. Will order new valve housing and belt for repair. ; ordrng 1 W11127357 (Valve housing) and 1 L14 (L14) and 1 W11239857 (Belt)
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ2
Near Piedmont, SC 29673
Jerry D.
Job Details:
03/26/2025
"Installed listed parts cycled unit through test and unit now giving FAE4. Code, that code is not on tech sheet, t line. 7741223880, Any code starting with A is actually 10, F10E4 code is for motor, replace motor , ordering, j13; ordrng 1 W11299377 (Motor sump assy)"
We serviced a
JENN-AIR REFRIGERATOR
Model JBSFS48NMX00
Near Simpsonville, SC 29681
Carl
Job Details:
03/26/2025
Found valve receiving voltage q16; ordrng 2 W11225845 (Valve)s and 1 WPW10121140 (Filter housing) and 1 Q16 (Labor)
We serviced a
WHIRLPOOL WASHER
Model WTW5100HC3
Near Easley, SC 29640
Larry M.
Job Details:
03/26/2025
Could get inner basket to separate due to rust. Will need outer basket and wash plate. ; ordrng 1 W11219115 (Outer basket) and 1 W10752283 (Wash plate)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ03
Near Asheville, NC 28803
Brian
Job Details:
03/26/2025
Found food in fresh food section freezing. Thermistors check ok in diagnostic. Harness (W10884720) Acu (W11043763) evap fan (W11334745) needed. ; ordrng 1 W11043763 (Acu) and 1 W11334745 (Evap fan) and 1 U18 (Job code) and 1 W10884720 (Harness)
We serviced a
MAYTAG WASHER
Model MVWC300VW1
Near Asheville, NC 28801
Brian
Job Details:
03/26/2025
"Installed agitator and agitator screw. Tested and found all operations ok at this time, with no leaks detected. Did not move unit."
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Hendersonville, NC 28792
Brian
Job Details:
03/26/2025
Found f8e1 (long fill). Tested unit in diagnostic and found cold water not entering unit. Inspected and found debris in valve. Also found belt squealing. Valve (W11513255) cam (W10721967) and belt (W11239857) needed. ; ordrng 1 W11513255 (Valve) and 1 W10721967 (Cam) and 1 W11239857 (Belt) and 1 L14 (Job code)
We serviced a
WHIRLPOOL DISHWASHER
Model DU1015XTXS2
Near Greenville, SC 29615
Nathan
Job Details:
03/26/2025
Removed knock-out plug from newly installed disposal. Tested operation and everythings performing as designed.
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Greenville, SC 29605
Nathan
Job Details:
03/26/2025
"Has F8E1 error long fill error. Filling normally so Im ordering control thats not recognizing water fill change while filling intermittently. Gear case is screeching in spin cycle and door lock wouldnt disengage when service diagnostics stopped. Ordering gear case,slider,valve,and door lock. Office will call and schedule return visit when parts arrive. ; ordrng 1 W11621180 (Control ACU) and 1 W11449841 (Gear case) and 1 W11700916 (Door latch) and 1 W10734521 (Slider) and 1 W11595805 (Valve) and 1 Q16laborcode (Q16 labor code)"
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Travelers Rest, SC 29690
Matt
Job Details:
03/26/2025
Found open contact in timer from bk to red jumped contact and heater hearts. Will order new timer.; ordrng 1 W11685947 (Timer) and 1 F12jobcode (F12 job code) and 1 Anytech (Any tech)
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAKZ3
Near Travelers Rest, SC 29690
Matt
Job Details:
03/26/2025
"Found float stuck in the up position. Realigned float. Started a cycle and watched unit fill, wash, drain with no issues."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM13
Near Roebuck, SC 29376
Sam
Job Details:
03/26/2025
Found unit not level when trying to level machine with cabinets. When leveling unit begins to rock back and forth. Will need shims for repair. Will order shims.; ordrng 4 4387828A (Shim)s and 1 J13 (J13)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ06
Near Reidville, SC 29375
Sam
Job Details:
03/26/2025
Upon arrival realized units handle that was ordered is incorrect color will re order correct color handle. Installed new user interface and screws. Calibrated measure water with measuring cup. Cycled measured fill. Measure fill is accurate now and functioning properly. Will re order handle.; ordrng 1 W11542651 (Handle stainless) and 1 C1 (C1)
We serviced a
MAYTAG WASHER
Model MVW5430MW2
Near Marshall, NC 28753
Kari
Job Details:
03/26/2025
"Took quick pics, found unit full of after and drain pump showing 20 ohms. The harness is broken to the pump, installed new harness unit checks ok"
We serviced a
WHIRLPOOL DRYER
Model WED500CMW0
Near Piedmont, SC 29673
Jerry D.
Job Details:
03/26/2025
"Installed listed parts cycled unit through test and unit still vibrating terrible, t line andrew run motor with blower off if it still vibration replace motor, also installed seal tape around vent and motor plate tightened all bulkhead screws and motor plate, completed all per t line, unit still vibrating bad, Per tline. order motor and blower again, 7741224083, Customer upset, Send supervisor, q16; ordrng 1 Q16 (Q16) and 1 Supervisor (Supervisor)"
We serviced a
WHIRLPOOL DRYER
Model LER7646DQ1
Near Fairview, NC 28730
Brian
Job Details:
03/26/2025
Installed new door catch and lent screen. Tested unit and found unit operations ok at this time but airflow restricted. Recommended customer have vent lines cleaned. Customer understands.
We serviced a
JENN-AIR MICROWAVE
Model JMW2430DP03
Near Simpsonville, SC 29681
Carl
Job Details:
03/26/2025
Installed new ui cycled unit to ck operation unit ck ok
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HW09
Near Anderson, SC 29626
Frank
Job Details:
03/26/2025
Found diode defective replaced diode tested unit working heating operating as intended; used 1 W11256462 (Does) from stock
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Anderson, SC 29624
Frank
Job Details:
03/26/2025
Found your case making squeaking noise replaced gear case tested cycle operating as intended
We serviced a
MAYTAG WASHER
Model MVWP586GW0
Near Anderson, SC 29621
Frank
Job Details:
03/26/2025
Replaced control. Calibrated ran test cycle running as designed
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Lake Lure, NC 28746
Brian
Job Details:
03/26/2025
"Found f8e1 (Long fill). Inspected and found some debris in valve but found water entering unit ok. Installed Control (W11513246) and Valve (W11513255). Calibrated and tested unit observing for leaks and proper functions. At this time, all operations ok with no leaks detected. Contacted safety team and documented sr number (7741161457); used 1 W11513255 (Valve TS) from stock"
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Mars Hill, NC 28754
Kari
Job Details:
03/26/2025
"Took quick pics, found unit full of after and drain pump showing 20 ohms. The harness is broken to the pump, installed new harness unit checks ok; used 1 W11643701 (Harness) from stock"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ11
Near Mars Hill, NC 28754
Kari
Job Details:
03/26/2025
Installed parts unit checks ok
We serviced a
WHIRLPOOL RANGE
Model WEG750H0HZ6
Near Weaverville, NC 28787
Kari
Job Details:
03/26/2025
"Took quick pics, another company was out and diagnosed a bad ignitor. Need ignitor for repair. Found spark module good and power to unit is 120v need part for repair. ; ordrng 1 W11661929 (Ignitor LF) and 1 Q16 (Job code)"
We serviced a
KITCHENAID TRASH COMPACTOR
Model KTTS505ESS2
Near Townville, SC 29689
Frank
Job Details:
03/26/2025
Found ran staying up not sitting off. Tested directional switch ok. Called tech line sr 7741219778. Replacing foot start switch.; ordrng 1 WPW10242556 (Switch) and 1 Jobcodej13 (Job code j13)
We serviced a
WHIRLPOOL COOKTOP
Model KCGC506JSS
Near Easley, SC 29642
Larry M.
Job Details:
03/26/2025
Found spark module not engaging. Will need spark module and harness. 465.22Spark module and harness ; ordrng 1 W11319687 (Spark module) and 1 W11344433 (Harness) and 1 N14jobcode (N14 job code)
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Easley, SC 29640
Larry M.
Job Details:
03/26/2025
Replaced manifold assembly. Ensured no leaks. All functions pass.
We serviced a
WHIRLPOOL DISHWASHER
Model KDTM404KPS3
Near Seneca, SC 29678
Frank
Job Details:
03/26/2025
Replaced adjusters on middle rack ok. Ordered wrong to rack need to reorder; ordrng 1 W11551395 (Track mount) and 1 W11569162 (Track mount)
We serviced a
WHIRLPOOL M/W OTR
Model WMMF7330RZ00
Near Inman, SC 29349
Chris
Job Details:
03/26/2025
Unit has scratched door and cover. Ordeing for repair ; ordrng 1 W11662375 (Vent) and 1 W11731160 (Door) and 1 Anytech and 1 Anytech and 1 Anytech and 1 Anytech
We serviced a
WHIRLPOOL WASHER
Model WFW9050XW00
Near Duncan, SC 29334
Chris
Job Details:
03/26/2025
Unit needs console assembly. Part is discontinued. Called third party team and spoke with cassina.unit is unrepairable . File number for call is 7741204986
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ3
Near Simpsonville, SC 29681
Carl
Job Details:
03/26/2025
Ran diagnostics found no error codes ran a test cycle to ck operation found as connection t the heater reinstalled the connector ck ok advised customer to use a jet dry and explained the cycles and the cycle add ons unit ck ok
We serviced a
MAYTAG WASHER
Model MVW5435PW0
Near Simpsonville, SC 29680
Carl
Job Details:
03/26/2025
Found belt lose installed new belt unit ck ok; used 1 W11239857 (Belt) from stock
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Simpsonville, SC 29680
Carl
Job Details:
03/26/2025
Found timer stalling and motor damaged motor bushings n15 ; ordrng 1 WPW10185982 (Timer) and 1 279827 (Motor) and 1 N15 (Labor)
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Fountain Inn, SC 29644
Carl
Job Details:
03/26/2025
Installed new sump ran diagnostics and a test cycle to ck operation unit ck ok
We serviced a
KITCHENAID RANGE
Model KSEG950ESS2
Near Greenville, SC 29609
Carl
Job Details:
03/26/2025
Found cooktop cracked due to thermal installed new cook top unit ck ok
We serviced a
JENN-AIR RANGE
Model JDS1750FP0
Near Greenville, SC 29615
Chris
Job Details:
03/25/2025
"Unit has open bake element, unit has 240 from control. Gave customer a bluebook estimate for repair at $714.36. Installed new element . Bake and broil will not heat . Now unit has no voltage at elements , flipped breaker again, voltage is good at terminal block. Control needs replaced. Gave customer a re written estimate at $966.54. Will, return tomorrow with control"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFC704FPS00
Near Greer, SC 29650
Chris
Job Details:
03/25/2025
"Unit has sealed system failure. Fresh food is at 46 and freezer is completely warm, . No frost pattern on evap . Unit doesnt make ice . Unit needs sealed system repair . Gave customer labor estimate of $1648.49. Customer denied repair"
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS3
Near Greer, SC 29650
Chris
Job Details:
03/25/2025
Found plug not knocked out of disposal. Removed plug. Unit check is ok. No leaks
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Piedmont, SC 29673
Larry M.
Job Details:
03/25/2025
Part came in damaged. Will need to reorder. ; ordrng 1 W11613479 (Sump assembly)
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS0
Near Simpsonville, SC 29680
Jerry D.
Job Details:
03/25/2025
"Unit was dropped, support bent, tub cracked, , customer upset wants unit replaced, w19; ordrng 1 W19 (W19) and 1 W11525187 (Sump and motor) and 1 W11467711 (Tub) and 1 W11623675 (Support)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WSF26C2EXF01
Near Greer, SC 29650
Carl
Job Details:
03/25/2025
Found door harness fatigued and open advised customer
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Pelzer, SC 29669
Carl
Job Details:
03/25/2025
Installed new harness ran diagnostics and a test cycle to ck operation unit ck ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model MSS25C4MGZ09
Near Easley, SC 29642
Larry M.
Job Details:
03/25/2025
Called TECHLINE Steve recommended SR:7741213519Thermistor out of range ; ordrng 2 WPW10384183 (Thermistor)s and 1 W11566891 (Control)
We serviced a
MAYTAG RANGE
Model MGR7700LZ1
Near Asheville, NC 28801
Brian
Job Details:
03/25/2025
"Unit pulled out when I arrived. Installed new valve and tubing. Tested all burners observing for leaks and proper functions. At this time, all operations ok with no leaks detected. Did not move unit. Left pulled out."
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Asheville, NC 28801
Brian
Job Details:
03/25/2025
"Tested unit and found it heating ok. Checked and found vent line kinked and debris around vent, on side of house. Recommend customer replace vent outside with one that goes straight out, instead of blowing into the ground. Corrected vent line kink. Tested unit and found all operations ok at this time."
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Lyman, SC 29365
Chris
Job Details:
03/25/2025
Cusotmer states unit doesnt heat. Unit has no stored faults. Unit passes auto test mode. Heater pulls 7.3 amps . Took picture of heater amps . Unit works as designed. Customer not using rinse aid. Refilled rinse aid. Called tech line and spoke With Austin . Unit works as designed. File number for call is 7741212170
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Lyman, SC 29365
Chris
Job Details:
03/25/2025
"Customer states stainless steel control panel gets hot . Unit is a stainless steel gas range. Customer has unit uninstalled upon arrival . Unit has f2 fault stored and showed Customer. Replaced control. Ran unit check. Unit hit target temp and cycled off as designed. No abnormal temperature or runaway temp . Unit vents below control panel. Showed customer vent, this is normal operation. Unit check is ok"