We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ0
Near Greenville, SC 29609
Flint
Job Details:
06/06/2023
"Found shorted ui f6e1 error, replaced ui and the unit tested good"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Greenville, SC 29609
Flint
Job Details:
06/06/2023
"Found belt had come loose and wrapped around the motor shaft, replaced the belt and put into a test cycle, the unit tested and good."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315Sdhm04
Near Powdersville, SC 29673
Jerry D.
Job Details:
06/06/2023
"Recoverd approximately 3 oz of refrigerant, installed listed parts, pulled 30 inches of vaccum, vaccum is holding, charged 4.6 oz, lowside 3 psi, good frost pattern on evaperator and temps are coming down rapidly, unit chks okay"
We serviced a
WHIRLPOOL WASHER
Model WTW8500DC5
Near Greenville, SC 29611
Flint
Job Details:
06/06/2023
"Replaced ui and put into a test cycle, the unit went through all the functions, it tested good."
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Simpsonville, SC 29681
Flint
Job Details:
06/06/2023
"Found bolt holding stator and rotor in place had fallen out, put loc-tite on screw and screwed back in tight, ran through a spin mode several times and checked the bolt again, the unit tested good."
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Simpsonville, SC 29681
Flint
Job Details:
06/06/2023
"Found fresh food evaporator thermistor out of specs, needs fresh food fan assembly. Estimate is 552. ; O-emld tckt"
We serviced a
WHIRLPOOL OVEN
Model KSGB900ESS4
Near Fountain Inn, SC 29644
Jerry D.
Job Details:
06/06/2023
"Customer did a reset and unit is working now, cancelled"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM08
Near Fountain Inn, SC 29644
Jerry D.
Job Details:
06/06/2023
"Evaperator fan motor inoperable, installed motor sent preid, cycled unit through test and unit checks okay"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Fountain Inn, SC 29644
Jerry D.
Job Details:
06/06/2023
"Fresh evaperator frozen wires burnt no power from cntrl, ordering, j13; ordrng 1 W11321510 (Cntrl) and 1 W11573116 (Assy harness)"
We serviced a
WHIRLPOOL RANGE
Model WFG320M0BS3
Near Simpsonville, SC 29680
Jerry D.
Job Details:
06/06/2023
"Burners and caps do not fit properly, ordering, j13; ordrng 2 W10183368 (Caps)s and 1 W10183369 (Cap) and 1 W10183370 (Cap) and 2 W10515455 (Burners front)s and 1 W10515454 (Burner) and 1 W10515453 (Burner)"
We serviced a
MAYTAG WASHER
Model MVWB765FW3
Near Simpsonville, SC 29680
Jerry D.
Job Details:
06/06/2023
"Was unable to separate tub and basket, shaft is corroded to tub, also dampers are worn out, installed agitator, ordering, Q16; ordrng 1 Q16 (Q16) and 1 W11134159 (Drive) and 1 W11226784 (Damper) and 1 W10512161 (Tub) and 1 W11089264 (Filter)"
We serviced a
WHIRLPOOL WASHER
Model MHW5630HC3
Near Zirconia, NC 28790
Derek
Job Details:
06/06/2023
F3E2 open or shorted ntc error. Installed harness but ntc wires are both black and none if the wires in harness labeled ntc harness match true wires on unit. On unit ntc wires are included in lower harness. Ntc shows 25 ohms. Will order parts to repair. N15; ordrng 1 W11557918 (Lower harness) and 1 W11550649 (ACU) and 1 W11314664 (Ntc)
We serviced a
MAYTAG WASHER
Model MVWX655DW1
Near Simpsonville, SC 29681
Carl
Job Details:
06/06/2023
Installed new spluch and belt ran diagnostics and a test cycle to ck operation unit ck ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW02
Near Greenville, SC 29615
Cliff
Job Details:
06/06/2023
Did not have right receipt
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM01
Near Simpsonville, SC 29681
Carl
Job Details:
06/06/2023
"Recovered 5.5 oz r134a removed compressor,evap and dry filter installed new compressor ,evap and dry filter installed 5.5 0zr134a cycled unit on and started to come down in temp unit ck ok"
We serviced a
WHIRLPOOL WASHER
Model MVW6230HW3
Near Greenville, SC 29615
Cliff
Job Details:
06/06/2023
"Found unit would not spin, just the agitator would spin. Also when I would cancel cycle the unit would continue trying to spin, I would have to unplug unit to get it to stop. The gearcase bad and at some point whenever I would power unit back on the canceling cycle message would appear and would not let me do anything else, ordering control.; ordrng 1 W11624938 (Control) and 1 W11449840 (Gearcase) and 1 W11590868 (Lower harness) and 1 U18jobcode (U18 job code)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Simpsonville, SC 29681
Flint
Job Details:
06/06/2023
"Replaced parts, put through a test cycle and the heater and unit tested good."
We serviced a
WHIRLPOOL M/W OTR
Model WMH78519LZ00
Near Greenville, SC 29617
Cliff
Job Details:
06/06/2023
"Customer explained to me that someone has agreed to replace the unit and does not want me to paint the black mark inside cavity. I talked to Chris from techline, 7736451006, got it documented with them they she refused repair."
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Zirconia, NC 28790
Derek
Job Details:
06/06/2023
Installed parts and cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMW0
Near Asheville, NC 28805
Matt
Job Details:
06/06/2023
Put unit in diagnostics and found no error codes. Ran auto test. All functions pass.
We serviced a
WHIRLPOOL WASHER
Model MHW6630HC0
Near Asheville, NC 28804
Matt
Job Details:
06/06/2023
"Put unit in diagnostics and found error codes F0E2,F5E2,F8E1,F0E5,( oversuds,lock failure,valve failure,off balance load) started a test cycle and unit added water and drained.Control just clicks. Will nit energize motor at all. Blue book estimate to replace valves,control and lock is 1475.00 Customer checking options."
We serviced a
WHIRLPOOL MICROWAVE
Model WMH32519HV5
Near Candler, NC 28715
Matt
Job Details:
06/06/2023
Installed new control. Control had no display. Found transformer on new control damaged. Will re order.; ordrng 1 L14jobcode (L14 job code) and 1 W11342846 (Control) and 1 Customerwantstopreschedule (Customer wants to pre schedule)
We serviced a
MAYTAG M/W OTR
Model MMV1175JZ0
Near Brevard, NC 28712
Derek
Job Details:
06/06/2023
Installed magnetron and cycled unit. Unit pulling 15+ amps and heating. Unit checks ok.
We serviced a
WHIRLPOOL WASHER
Model MVWC565FW3
Near Franklin, NC 28734
Kari
Job Details:
06/06/2023
"Took quick pics, found unit wouldnt move past wash, found unit showing an 8-1 long fill code. Cleared sediment from screen and ran through a recalibration. Ran unit through spin manually found it sounds louder than it should. Tipped unit back and found gearcase oil in the shield. Will need parts for repair ; ordrng 1 W11454734 (Gearcase) and 1 W10721967 (Cam) and 1 N15 (Job code) and 1 Okanytech (Ok any tech)"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF507ESS01
Near Seneca, SC 29672
Frank
Job Details:
06/06/2023
Getting air leak in back of ice maker assembly causing freezing water line and ice buildup in front. Rear gasket 11.67. 30.90 called Techline suggested gasket w11159728 30.00 ; ordrng 1 W11159728 (Gasket) and 1 WPW10280988 (Supply gasket) and 1 WPW10320706 (Return gasket)
We serviced a
WHIRLPOOL OVEN
Model WOS51EC7HS20
Near Seneca, SC 29672
Frank
Job Details:
06/06/2023
Inner door glass broke when on self clean mode . ; ordrng 2 WPW10284902 (Inner door glass)s and 1 Jobcodej13 (Job cod j13) and 1 W11598188 (Retainer divider)
We serviced a
JENN-AIR RANGE
Model JDRP548WP03
Near Salem, SC 29676
Frank
Job Details:
06/06/2023
Found on 18 inch door inner glass broken #3 on door parts shows discontinued.. W10115693.. called Techline. Can't give estimate due to can't get glass price 150.00 trip 149.99 Labor collecting trip charge for now; ordrng 1 W10115693 (Inner door) and 1 Jobcodel14 (Job code l14)
We serviced a
WHIRLPOOL OVEN
Model WFE535S0LZ2
Near Maggie Valley, NC 28751
Kari
Job Details:
06/06/2023
"Took quick pics, found the convection fan making noise as it spins, customer states it normally sounds like a screw is rattling around. When I took the fan cover off and ran it there was no noise, but did find the blade wobbles back and fourth as it spins, found the nut that holds the blade was stripped and couldnt be tightened down need parts for repair ; ordrng 1 W11582241 (Fan convection with blade) and 1 L14 (Job code) and 1 Okforanytech (Ok for any tech)"
We serviced a
JENN AIR RANGE
Model JES1750FS2
Near Sylva, NC 28779
Kari
Job Details:
06/06/2023
"Installed parts, ran cooktop on all 4 elements for 15-20 minutes on high and everything continued to boil and never shut off unit checks ok"
We serviced a
KITCHEN AID DISHWASHER
Model KDFM404KPS0
Near Clyde, NC 28721
Kari
Job Details:
06/06/2023
"Took quick pics, found unit giving a float switch code 84 customers had made a pot of coffee and basically the whole pot Hitzfield onto the floor and it looks like maybe between the cabinet when I took the bottom kick plate off found there to be dried coffee in the tray cleaned out tray. Also cleared out codes. Ran diagnostic cycle. Found all functions check OK
We serviced a
WHIRLPOOL RANGE
Model GW399LXUS05
Near Hendersonville, NC 28791
Brian
Job Details:
06/06/2023
"Natural gas. Found bake burner not igniting. Glow bar is glowing. Contacted tech support and spoke to Brandon. We checked and found bake glow bar, not drawing enough amps. Glow bar (74007498) is weak, and in need of replacement. Quoted customer 217.02 to complete repairs. Informed customer that the bake burner, itself, is no longer available and if the screws holding igniter in place, break, than repairs may not be able to be completed. Customer understood and wished to think about repairs. Sr # for tech line (7736572026) Sr # for safety team (7736527230)"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Hendersonville, NC 28739
Brian
Job Details:
06/06/2023
"Installed new belt and inlet valve. Recalibrated and tested unit observing for leaks and proper functions. At this time, all operations ok with no leaks detected."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHW05
Near Spartanburg, SC 29307
Tyler
Job Details:
06/06/2023
Customer states unit stopped making ice. Temps are good. Tried to jump icemaker. It did not move.; ordrng 1 W11284458 (Icemaker) and 1 W11518204 (Control) and 1 L14jobcode (L14 job code)
We serviced a
WHIRLPOOL WASHER
Model MVW4505MW0
Near Spartanburg, SC 29307
Tyler
Job Details:
06/06/2023
"Found wiring to drain pump pinched from manufacturer. Fixed wiring, tested for operation. All functions tested good."
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS0
Near Hendersonville, NC 28739
Brian
Job Details:
06/06/2023
"Found wash motor running loud. Installed new pump and motor assembly and tested unit multiple times observing for leaks and proper functions. At this time, all operations ok with no leaks detected."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ06
Near Hendersonville, NC 28792
Brian
Job Details:
06/06/2023
Found freezer evaporator frozen over. Inspected and found thermistor open. Inspected and found Heater(W11650661) and defrost thermostat (WPW10384183) needed. ; ordrng 1 W11566891 (Control) and 1 WPW10384183 (Defrost thermostat) and 1 W11650661 (Heater) and 1 Q16 (Job code)
We serviced a
WHIRLPOOL DISHWASHER
Model DU1055XTVB0
Near Spartanburg, SC 29301
Tyler
Job Details:
06/06/2023
Found a clog in drain hose at disposal. Cleared hose. Filled u it with water and drained out. All functions tested good.
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Boiling Springs, SC 29316
Tyler
Job Details:
06/06/2023
Found latch and bezel broken. Ordering bezel; ordrng 1 W11545554 (Bezel)
We serviced a
MAYTAG WASHER
Model MHW5630HW3
Near Spartanburg, SC 29316
Tyler
Job Details:
06/06/2023
Customer states they find some water on seal at end of cycle. Instructed customer that water will be on seal during cycle and proper cleaning and maintenance of door seal.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ06
Near Chesnee, SC 29323
Tyler
Job Details:
06/06/2023
Found faulty switch error. Ordering switches.; ordrng 1 W11469740 (Switch) and 1 W11123943 (Switch) and 1 L14jobcode (L14 job code)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ07
Near Inman, SC 29349
Tyler
Job Details:
06/06/2023
Found evap started to freeze over. Will have to thaw on return.; ordrng 1 W11661931 (Evap motor) and 1 N15jobcode (N15 job code)
We serviced a
WHIRLPOOL RANGE
Model WFG320M0BS3
Near Fairview, NC 28730
Brian
Job Details:
06/06/2023
Found left rear burner switch bent. New Left rear (W10861716) switch needed. Quoted customer 314.61 to complete repairs. ; ordrng 1 J13 (Job code) and 1 W10861716 (LR valve)
We serviced a
WHIRLPOOL WASHER
Model WTW5015LW0
Near Lyman, SC 29365
Chris
Job Details:
06/06/2023
Installed new latch. Unit check is ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ02
Near Simpsonville, SC 29680
Carl
Job Details:
06/06/2023
Installed new imk and led unit ck ok
We serviced a
WHIRLPOOL REFRIGERATOR
Near Mauldin, SC 29662
Carl
Job Details:
06/06/2023
Cancled on phone
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ1
Near Greenville, SC 29609
Derek
Job Details:
06/06/2023
"Unit worked properly for several weeks then slide started sticking and not going all the way in even with coins so not same issue but not allowing operation at all. Found slide screw hitting coin basket, set too far down. Raised slide screw and checked operation. Will not operate w/o coins, hits stop w/o coins, is sliding in and back out with coins and working properly."
We serviced a
WHIRLPOOL RANGE
Model KFGG500ESS0
Near Greenville, SC 29617
Cliff
Job Details:
06/06/2023
"Found the back left burner will not ignite, the spark goes off to the side, tried cleaning the burner cap, the burner head, and the area underneath the head. Switch the igniter with the middle burner, the middle burner still worked fine but the back right still did not, giving customer an estimate of 346.17-34.62(10% senior discount) 311.55, he approved, paid 155.78 today and will owe 155.77 when completed.; ordrng 1 J13jobcode (J13 job code) and 1 WPW10515453 (Burner head)"
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Lake Toxaway, NC 28747
Frank
Job Details:
06/06/2023
F7e5 shifter fault f7e1.. nut keeps coming off bottom of gearcase.. replacing gearcase cam and actuator; ordrng 1 W11454372 (Gearcase) and 1 W10721967 (Splutch kit) and 1 W11481722 (Actuator) and 1 Jobcodel14 (Job code l14)
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Greenville, SC 29609
Chris
Job Details:
06/06/2023
Installed new parts.. Unit check is ok
We serviced a
WHIRLPOOL RANGE
Model WFE550S0HZ1
Near Greenville, SC 29605
Flint
Job Details:
06/05/2023
"Replaced control board and tested all element on top and in oven, everything tested good at this time."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Greenville, SC 29605
Flint
Job Details:
06/05/2023
"Replaced control and put the unit into test mode, the unit tested good."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Belton, SC 29627
Jerry D.
Job Details:
06/05/2023
"Valve broken, installed valve sent preid, cycled unit through test and no leaks found unit checks ok"
We serviced a
WHIRLPOOL RANGE
Model WFC150M0JB3
Near Belton, SC 29627
Jerry D.
Job Details:
06/05/2023
Terminal block broken installed wpw 10245259 from truck stock cycled unit through test and all functions are working properly
We serviced a
WHIRLPOOL DISHWASHER
Model WDF331PAHS1
Near Greenville, SC 29605
Cliff
Job Details:
06/05/2023
"6-4- float switch open, 4-3: motor not running, 7-1: no heat. Unit would drain but the wash motor would not run, ordering parts.; ordrng 1 W11025157 (Sump assembly) and 1 W11087226 (Control) and 1 N15jobcode (N15:job code)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF331PAHS1
Near Greenville, SC 29605
Cliff
Job Details:
06/05/2023
"Found pump not working, replaced pump cycled unit and drained water, let customer see that unit would fill and drain, all functions check ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT518SZFM02
Near Taylors, SC 29687
Cliff
Job Details:
06/05/2023
"Found the defrost thermistor only showed 700 ohms while in ice, replaced thermistor, again tested the defrost heater, thawed out evaporator, all functions check ok"
We serviced a
WHIRLPOOL RANGE
Model WGG745S0FS02
Near Pelzer, SC 29669
Jerry D.
Job Details:
06/05/2023
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
KITCHEN AID WALL OVEN
Model KOCE500EBS08
Near Cowpens, SC 29330
Tyler
Job Details:
06/05/2023
"Installed parts, tested for operation. All functions tested good. Collected 829.71 via card."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHB04
Near Boiling Springs, SC 29316
Tyler
Job Details:
06/05/2023
Leveled doors. Tested for operation. All functions tested good.
We serviced a
MAYTAG DISHWASHER
Model MDBH970AWB
Near Easley, SC 29642
Frank
Job Details:
06/05/2023
Door latch seized.. can not operate.. needdoor latch pieces; ordrng 1 WPW10130695 (Door latch) and 1 WPW10275768 (Latch assembly) and 1 Jobcodel14 (Job code l14)
We serviced a
WHIRLPOOL RANGE
Model WFE535S0LS0
Near Easley, SC 29642
Frank
Job Details:
06/05/2023
Installed switch and element tested working ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model wrt311fzdw02
Near Spartanburg, SC 29307
Tyler
Job Details:
06/05/2023
Found RC section not cooling. Excessive frost in FC. Heater and evap motoer tested good. Ordering harness.; ordrng 1 W11618502 (Wire harness) and 1 L14jobcode (L14 job code)
We serviced a
WHIRLPOOL DRYER
Model WHD560CHW2
Near Asheville, NC 28801
Derek
Job Details:
06/05/2023
"Unit in warranty pic of closing in quick pics and customer contacting whirlpool to update warranty info which per Veronica at trade partner would not be a problem. Unit shutting off and giving F9E2 drain error. Would not give error during testing and unit has no service test that allows just the drain pump to be ran. Unit needs drain pump assy and control, will have to br uninstalled to repair so 2 person job. N15 2 man. ; ordrng 1 W11551760 (Pump) and 1 W11565028 (ACU) and 1 2manjob (2 ppl)"
We serviced a
JENN-AIR WALL OVEN
Model JJW2430DP02
Near Fairview, NC 28730
Derek
Job Details:
06/05/2023
Installed panel covered and sent to customer by manufacturer. Cycled unit and checked calibration. Oven averaging 354° cycled at 350°. Left calibration set to default. Unit checks ok.
We serviced a
KITCHENAID REFRIGERATOR
Model KUID308HPS01
Near Fairview, NC 28730
Brian
Job Details:
06/05/2023
Installed all parts ordered. Tested all functions and found all operations ok with no leaks detected. Did not move unit.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325FDAM02
Near Hendersonville, NC 28791
Brian
Job Details:
06/05/2023
"Found freezer and fresh food led out. Inspected and found fresh food Led module (WPW10515058) in need of replacement. Quoted customer 489.54. Customer wished to proceed with repairs. Collected total. ; ordrng 1 WPW10515057 (Led , bring just in case) and 1 WPW10515058 (Fresh food led) and 1 F12 (Job code)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADW7
Near Hendersonville, NC 28791
Brian
Job Details:
06/05/2023
Found element visually broken. A piece broke off element and melted a small hole in tub. New Tub (W11513977) and pump and motor (W11025157) needed. ; ordrng 1 W11513977 (Tub) and 1 W19 (Job code) and 1 W11025157 (Pump and motor)
We serviced a
WHIRLPOOL DISHWASHER
Model WDP560HAMZ0
Near Hendersonville, NC 28739
Brian
Job Details:
06/05/2023
"Found left door spring rubbing on unit frame. Adjusted and tested, with customer present. At this time, all operations ok with no leaks detected."
We serviced a
WHIRLPOOL RANGE
Model WFC150M0JW3
Near Piedmont, SC 29673
Jerry D.
Job Details:
06/05/2023
"Customer says cooktop gets to hot when using oven, found customer has foil under burners covering oven vent, removed foil and cycled oven, top temp now chks ok, customer is ELDERLY and doesnt want this unit because of controller, she wants a range with a clock and a dial for the oven, instructed customer how to use controls , she is still not happy, advised customer to call lowes and whirlpool customer service"
We serviced a
WHIRLPOOL RANGE
Model WFG505M0BS4
Near Spartanburg, SC 29306
Tyler
Job Details:
06/05/2023
"Tested oven, oven lit and preheated on bake and broil. All other functions tested. No issues found."
We serviced a
AMANA REFRIGERATOR
Model ASI2175GRS08
Near Spartanburg, SC 29306
Tyler
Job Details:
06/05/2023
Found icemaker was turned off. Cycled icemaker. All functions tested good.
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Easley, SC 29642
Frank
Job Details:
06/05/2023
Tested heating comes up to 160 with vent off 180 with vent on. Drops 1 degree per second poor vent.
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Seneca, SC 29678
Frank
Job Details:
06/05/2023
Installed parts tested working ok
We serviced a
JENN-AIR COOKTOP
Model JGD3536GS00
Near Seneca, SC 29672
Frank
Job Details:
06/05/2023
All electrodes keep sparking after burners are lit.. replaced spark module no difference. Doesn't look like any short in wires. Re wiring system.; ordrng 1 W10861397 (Switch harness) and 1 W10876259 (Lf electrode) and 1 W10905489 (Lr electrode) and 1 W10876260 (Cf electrode) and 1 W10876261 (Cr electrode) and 1 W10876262 (Rr electrode) and 1 W10834701 (Wire harness) and 1 Jobcodel14 (Job code l14)
We serviced a
JENN-AIR RANGE
Model JES9800CAB01
Near Seneca, SC 29672
Frank
Job Details:
06/05/2023
Installed bake element tested working ok
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Westminster, SC 29693
Frank
Job Details:
06/05/2023
Found when motor engaging shuts machine off. Motor shorts system out. Ordering wire harness as per caution; ordrng 1 W10890624 (Motor) and 1 W11428524 (Capacitor) and 1 W10903238 (Wire harness) and 1 W11603810 (Control board) and 1 Jobcodel14 (Job code l14)
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Etowah, NC 28729
Brian
Job Details:
06/05/2023
"Found rollers worn and spinning improperly, causing squealing noise. Also found level legs missing. Idler (WP691366) repair kit (4392067) and level legs (W11025920) needed. ; ordrng 1 WP691366 (Idler) and 1 4392067 (Repair kit) and 1 W11025920 (Level legs) and 1 L14 (Job code)"
We serviced a
KITCHEN AID RANGE
Model KFEG500ESS3
Near Greenville, SC 29605
Cliff
Job Details:
06/05/2023
"Found the red wire burnt through, the terminal block was messed up as well. Gave customer an estimate of 387.06 for the parts, labor, and TC. He approved, cycled the burners and preheated oven, all functions check ok.; used 1 WPW10245259 (Terminal block), 1 4-prong range cord (4-prong range cord), and 1 N15 job code (N15:job code) from stock"
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Leicester, NC 28748
Kari
Job Details:
06/05/2023
"Took quick pics, found unit showing f8e1 low flow code. Found hot and cold turned on, but hardly any cold water comes out. Found the solenoid impacted with clay and mud. Installed new valve, ran diagnostic cycle again, unit checks ok Advised customer get a secondary water filter for the cold line on the machine to prevent future blockages."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ03
Near Easley, SC 29642
Frank
Job Details:
06/05/2023
Fridge tempn40 set to 34. Freezer set to -5 at 12 degrees. Compressor rattling..no error in66 e2 error on 56. Harvest ice maker test ok. No other errors in diagnostics..; ordrng 1 W11578205 (Compressor) and 1 W11504431 (26a) and 1 W11504415 (26b) and 1 W11506621 (26c) and 1 W11506635 (26d) and 1 W11575003 (3way valv e) and 1 W11109499 (Dryer) and 1 R600 (R600) and 1 Sealedsystemtech (Sealed system tech) and 1 Jobcodex20 (Job cod x20)
We serviced a
KITCHEN AID DISHWASHER
Model KDPE234GPS0
Near Gaffney, SC 29341
Tyler
Job Details:
06/05/2023
"F4e3, F2e1, F7e1 errors. Gave estimate for for sump; ordrng 1 W11085683 (Sump) and 1 L14jobcode (L14 job code)"
We serviced a
WHIRLPOOL DRYER
Model WED4850HW0
Near Gaffney, SC 29341
Tyler
Job Details:
06/05/2023
Found start knob got wiggled loose and was not making contact with switch. Repositioned knob. Tested unit. All functions tested good.
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW0
Near Mills River, NC 28759
Brian
Job Details:
06/05/2023
"Installed new tub ring. Tested unit observing for leaks and proper functions. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
KITCHEN AID DISHWASHER
Model KDTE334GPS0
Near Greenville, SC 29615
Chris
Job Details:
06/05/2023
Installed new parts. Unit check is ok . No leaks
We serviced a
KITCHEN AID RANGE
Model KSGB900ESS0
Near Greenville, SC 29615
Chris
Job Details:
06/05/2023
Unit has multiple key pad faults. Gave customer a bluebook estimate for repair tax. Installed new part. Unit reached set point of 350. Unit check is ok
We serviced a
MAYTAG DRYER
Model MEDB980BW0
Near Greer, SC 29650
Chris
Job Details:
06/05/2023
Found bad roller wheels. Gave customer a bluebook estimate for repair with tax at. Installed new parts . Unit check is ok
We serviced a
WHIRLPOOL MW OVEN COMBO
Model KOCE507ESS22
Near Greer, SC 29650
Chris
Job Details:
06/05/2023
Installed new parts. Unit check is ok . K17b571nl2
We serviced a
WHIRLPOOL WASHER
Model NTW4750BQ0
Near Greenville, SC 29607
Cliff
Job Details:
06/05/2023
"Replaced parts, cycled unit through calibration and auto test, all functions check ok"
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Fair Play, SC 29643
Jerry D.
Job Details:
06/05/2023
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
WHIRLPOOL DRYER
Model WED5100HW2
Near Taylors, SC 29687
Chris
Job Details:
06/05/2023
Heater checks at 9ohms. Cuttoff fuses check ok . Volatge good at terminal block and no voltage drop under load . Thermal fuse checks ok .Ordering parts for repair ; ordrng 1 W11525997 (Control) and 1 WP697772 (Wheel) and 1 L14 and 1 W11549461 (Motor)
We serviced a
JENN AIR RANGE
Model JES9800AAB
Near Greer, SC 29651
Chris
Job Details:
06/05/2023
Unit has cracked cook top. Gave customer a bluebook estimate with tax at 334.21. Customer denied estimate
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFC704FPS01
Near Greer, SC 29651
Chris
Job Details:
06/05/2023
Installed new parts. Unit check is ok tpb10049l2.0
We serviced a
WHIRLPOOL WASHER
Model NTW4750BQ0
Near Greenville, SC 29607
Flint
Job Details:
06/05/2023
"Replaced entire tub assembly, with Cliff. Double labor rate authorization tpb10055l2.0"
We serviced a
WHIRLPOOL DISHWASHER
Model WDP560HAMZ0
Near Arden, NC 28704
Brian
Job Details:
06/05/2023
"Found no saved error codes. Ran unit through auto diagnostics and found all functions ok and heater coming on. Recommended customer use rinse aid in unit and recommended customer preheat water at sink prior to starting cycle, and to open unit when cycle is complete, to allow moisture to leave unit. Informed customer that plastic items may not dry an moisture pooled on top of coffee cups, and similar items, is normal. Customer understood. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
KITCHENAID M/W OTR
Model KMHS120ESS11
Near Alexander, NC 28701
Kari
Job Details:
06/05/2023
"Took quick pics, found light not turning on, found the bulb blown. Installed new bulb. Unit checks ok; used 1 8206232A (Bulb) from stock"
We serviced a
WHIRLPOOL MICROWAVE
Model WMH31017HS09
Near Pendleton, SC 29670
Jerry D.
Job Details:
06/05/2023
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
MAYTAG WASHER
Model MVWC565FW3
Near Weaverville, NC 28787
Kari
Job Details:
06/05/2023
"Took quick pics, found unit showing no codes. The customer is concerned about mildew smell even after running bleach cycles and cleaning cycles. Took agitator off and pulled basket out. Found the outside of the basket coated in a film, the same film is on the tub and all over the shaft of the gearcase. Took off drain pump cover and cleaned the underside of that off. Customer is not using Fabric softener the soap on the shelf above me is tied and they do have gain powder. Customer states that they use the liquid tide more one of the tides does have Downey and end. Customer also states that they using about half of the cup of soap I told him to back it down to more like the second level on the cup. Call Techline and spoke with Robert. He went over water, hardness fabric softener, usage detergent, usage minerals in the water supply with me. I reported to him that we have soft water. Customer is cleaning it regularly with affresh and with bleach based on findings the deep, clean and backing off on soap usage should correct the problem. Robert @techline 7736560327"
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Weaverville, NC 28787
Kari
Job Details:
06/05/2023
"Took quick pics, found unit showing an 8-1 long fill code. Ran unit through diagnostics test, unit wouldnt fill and just hummed. Confirmed water is on at tap. Installed new valve. Reran diagnostic test, foundunit now fills and agitates and spin ; used 1 W11513255 (Valve) from stock"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Mars Hill, NC 28754
Kari
Job Details:
06/05/2023
"Took quick pics, found unit not getting water to door or icemaker. Found the valve doesnt hi: but theres 120v to valve. Installed new valve. Unit checks ok; used 1 W11645245 (Valve) from stock"
We serviced a
WHIRLPOOL DISHWASHER
Model JDPSS244LL2
Near Burnsville, NC 28714
Kari
Job Details:
06/05/2023
"Took quick pics, found unit showing F7E2 put unit into diagnostics and cleared code. Tried running diagnostics test, found it filled and immediately started to code when it flipped over to the motor. Found there to be 16.9 ohms from motor found harness has good resistance. According to tech sheet will need control and motor for repair. Control is on BO, let contractor know. And going to have parts department call customer with eta on BO board ; ordrng 1 W11632704 (Control) and 1 W11460946 (Sump) and 1 W11434044 (Valve) and 1 N15 (Job code)"