We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Woodfin, NC 28804
Kari
Job Details:
05/03/2023
"Took quick pics, found unit just humming and wont spin, foundunit showing 7-1 basket reengagement fault. Ran through diagnostics test found unit hums when it goes to agitate and if you manually try to spin it. It fills and drains fine. Found the capacitor to show an OL, also found gearcase oil all over cam. Lights no longer come on when the knob is spun Will need gearcase and board for repair ; ordrng 1 W11454741 (Gearcase) and 1 W11170319 (Control) and 1 N15 (Job code) and 1 W10721967 (Cam), used 1 W11428524 (Capacitor) from stock"
We serviced a
WHIRLPOOL WASHER
Model MVWC465HW2
Near Leicester, NC 28748
Kari
Job Details:
05/03/2023
"Took quick pics, found unit had slipped over and become off balance. Customer also said it leaked on the floor. Found unit showing no codes, ran unit through diagnostics test, leveled feet but found the tub to wobble side to side in spin more than it should. Pressed down on tub and found suspension to be weak. Gave customer est of 394.74. Customer will call us back if they want repaired had office run cc for 50 TC and email receipt"
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Greenville, SC 29605
Cliff
Job Details:
05/03/2023
"Talked to Rick from techline, 7736304750, he was not able to give me a straight forward answer on what i should do, he said if at first you dont succeed try try again and to use grease on spots that seem to rub. Matt said to use some foam tape around the area that the lid and cabinet meet. ; saved tckt"
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Asheville, NC 28804
Kari
Job Details:
05/03/2023
"Took quick pics, found units motor head cracked and was dangling and when it runs it vibrates against the floor and vibrates against the machine making excessive noise need pumped for repair. Also told builder that part is on BO; ordrng 1 W11613479 (Pump assembly) and 1 J13 (Job code)"
We serviced a
WHIRLPOOL M/W OTR
Model WMH78519LZ00
Near Greenville, SC 29605
Cliff
Job Details:
05/03/2023
"Door closes on its own when inside 90 degrees, but holds open at 90, the installation looks ok, the cabinet is not completely plumb based off looking at either side of the microwave, i did advise him that he would need whoever installed to recheck that if he is unsure."
We serviced a
KITCHEN AID ICE MACHINE
Model KUIX535HPS00
Near Greenville, SC 29615
Cliff
Job Details:
05/03/2023
"Just control is 665.75, control and valve is 824.67. Found unit would go through its normal cycles of filling, pumping over cold plate, and harvesting, but it would do them all within a minute or two. The water pressure is low as well, unit does not have a filter. I gave customer an estimate for just the control and both the control and valve. I told him that even if it was cycling correctly that the ice probably wouldnt be right because of the low pressure. He said they would get back to us."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHB00
Near Liberty, SC 29657
Matt
Job Details:
05/03/2023
Found freezer fan covered in ice. Put unit in defrost and tested operation. Defrost operates correctly and evaporator is clear only the fan and outer cover are frosted. Most likely door want closed completely or package held door open. Thawed out fan and housing. For its sealing properly. Customer also stated water has a bad taste and smell. Blue book estimate of 298.54. To replace the inlet water line to the whirlpool approved p.e.x line. Balance on return is 148.54; ordrng 1 W10267701RP (Water line) and 1 J13jobcode (J13 job code) and 1 Anytech (Any tech)
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS01
Near Simpsonville, SC 29680
Cliff
Job Details:
05/03/2023
"Replaced gasket for the right hand fresh food door, also found the rails for the freezer are going bad, the door does not open or close like it should, ordering parts.; ordrng 1 W11241580 (LH bracket) and 1 W11241268 (RH bracket) and 1 L14jobcode (L14 job code)"
We serviced a
KITCHEN AID DISHWASHER
Model KDTM404ESS3
Near Taylors, SC 29687
Cliff
Job Details:
05/03/2023
"Found where the heater is warped which caused one section of the wash arm to melt, ordering parts.; ordrng 1 W10860176 (Lower washarm) and 1 W10703867 (Heater) and 1 N15jobcode (N15 job code)"
We serviced a
WHIRLPOOL WASHER
Model MVW4505MW0
Near Burnsville, NC 28714
Kari
Job Details:
05/03/2023
"Took quick pics found unit wouldnt start, but we just make a clicking noise Found it when he got to the agitation part of the diagnostic cycle unit wouldnt go any further found that the actuator was clicking installed new actuator unit checks, OK; used 1 W10913953 (Actuator) from stock"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Taylors, SC 29687
Cliff
Job Details:
05/03/2023
"F4-E3: motor not running. Unit would fill but motor was not starting, I tapped on it and it kicked on, giving customer an estimate of 522.74, customer approved, will pay 261.37 today and will owe 261.37 when completed.; ordrng 1 W11665769 (Sump aasembly) and 1 N15jobcode (N15 job code)"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706EBS01
Near Inman, SC 29349
Chris
Job Details:
05/03/2023
Freezer wire light has broke off in liner. Liner tape applied from factory caused wire to break. Called tech line and spoke with Ed. Unit is unrepairable. File number for call is 7736320724
We serviced a
WHIRLPOOL WASHER
Model NTW4750BQ0
Near Greenville, SC 29607
Flint
Job Details:
05/03/2023
"Tried replacing gearcase, it was stuck in the tub, tried to beat out , but it would not come, will need to see if the third party would like to replace the tubs as well. W10521298 basket, W10528947 hub, W10324648 outer tub. W10324647 tub seal. WPW10215093, WPW10215093 pump WP8533928 screw x 2. Will have to check with joe in the morning ; O-emld tckt"
We serviced a
WHIRLPOOL RANGE
Model WFG320M0BS3
Near Greer, SC 29651
Chris
Job Details:
05/02/2023
Spoke with customer. Ordering for first call complete ; ordrng 1 W11176456 (Glass) and 1 W10894054 (Handle) and 1 W11105139 (Glass) and 1 WPW10535767 (Glass) and 1 L14
We serviced a
KITCHEN AID REFRIGERATOR
Model KFIS27CXMS1
Near Greer, SC 29651
Derek
Job Details:
05/02/2023
Found split in ice maker fill tube. Gave estimate to replace tube of 357.14. Customer okd estimate. Will order part. Balance will be 78.57L14; ordrng 1 WPW10213219 (Tube)
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706EBS01
Near Townville, SC 29689
Matt
Job Details:
05/02/2023
Drawer u.i not responding. Unut cutting off every 2 minutes and throwing p.o on display. Will order parts needed for repair; ordrng 1 WPW10769076 (Drawer ui) and 1 W11170612 (Drawer harness) and 1 Q16jobcode (Q16 job code) and 1 WPW10675033 (Main control) and 1 W11249952 (Freezer fan) and 1 W11087438 (Fresh food fan) and 1 PPPneedsapproval (PPP needs approval)
We serviced a
WHIRLPOOL WASHER
Model wtw4816fw3
Near Greer, SC 29651
Chris
Job Details:
05/02/2023
ran washer through cycles and poduct is operating as designed
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Greer, SC 29650
Cliff
Job Details:
05/02/2023
"Replaced part, cycled unit through calibration and auto test, all functions check ok."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHV08
Near Greenville, SC 29609
Cliff
Job Details:
05/02/2023
"Unit is running slightly warm, it seems there is either a small leak or a partial restriction, I can hear refrigerant flowing and the first tubing on evaporator is frosted over, will need sealed system tools, ordering parts.; ordrng 1 Vacuum (Vacuum) and 1 Scale (Scale) and 1 R600 (R600) and 1 X20:jobcode (X20 job code) and 1 Nitrogen (Nitrogen)"
We serviced a
WHIRLPOOL RANGE
Model WFG505M0BS3
Near Greer, SC 29650
Chris
Job Details:
05/02/2023
Installed new parts. Unit check is ok
We serviced a
WHIRLPOOL DRYER
Model wed5010lw0
Near Easley, SC 29640
Matt
Job Details:
05/02/2023
"Replaced motor and blower, checks o.k"
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Easley, SC 29640
Matt
Job Details:
05/02/2023
"Replaced motor and blower, checks o.k"
We serviced a
WHIRLPOOL WASHER
Model MVW7230HW0
Near Simpsonville, SC 29681
Carl
Job Details:
05/02/2023
Need to set up appt so while im there i can call tech line back; O-emld tckt
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ03
Near Honea Path, SC 29654
Jerry D.
Job Details:
05/02/2023
"Compressor inoperable, ordering Q16; ordrng 1 Q16 (Q16) and 1 600 (600) and 1 W11574734 (Comp kit) and 1 W10913906 (Avx)"
We serviced a
KITCHEN AID RANGE
Model KFDC506JSS01
Near Pelzer, SC 29669
Jerry D.
Job Details:
05/02/2023
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
JENN-AIR REFRIGERATOR
Model JFFCF72DKL04
Near Greenville, SC 29601
Cliff
Job Details:
05/02/2023
"Replaced parts, lights works, all functions check ok."
We serviced a
WHIRLPOOL M/W OTR
Model WML55011HS3
Near Travelers Rest, SC 29690
Flint
Job Details:
05/02/2023
"Found f1e4, relay on board, will order; ordrng 1 W11244085 (Pcb) and 1 W11129648 (Board)"
We serviced a
WHIRLPOOL DRYER
Model WED5010LW0
Near Travelers Rest, SC 29690
Flint
Job Details:
05/02/2023
"Replaced door and associated parts, the unit tested good."
We serviced a
WHIRLPOOL RANGE
Model WFE540H0ES0
Near Travelers Rest, SC 29690
Flint
Job Details:
05/02/2023
"Replaced the bake element and tested all functions, the unit tested good."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRQA59CNKZ
Near Arden, NC 28704
Brian
Job Details:
05/02/2023
"Found right fresh food door gasket torn, and mullian broken. Gasket (W11456682) and mullian (W11455378)needed; ordrng 1 W11456682 (Gasket) and 1 W11455378 (Mullian) and 1 L14 (Job code)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS335SDHM06
Near Arden, NC 28704
Brian
Job Details:
05/02/2023
Found freezer evaporator frozen over. Removed all ice build up. I found defrost heater unplugged. Plugged heater in and tested. Found heater now coming on. Tested all functions and found all operations ok with no leaks detected.
We serviced a
AMANA DISHWASHER
Model ADB1400AGB1
Near Easley, SC 29642
Matt
Job Details:
05/02/2023
"Installed new control, harness and dispenser. Tested operation, checks o.k"
We serviced a
WHIRLPOOL DRYER
Model ned4655ew1
Near Easley, SC 29640
Matt
Job Details:
05/02/2023
"Replace motor and blower,checks o.k"
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC703HPS00
Near Greer, SC 29650
Chris
Job Details:
05/02/2023
Installed new light. Unit check is ok
We serviced a
MAYTAG WASHER
Model MVWC565FW3
Near Mauldin, SC 29662
Flint
Job Details:
05/02/2023
"Found the board acting up, no error codes. Replaced the board, recalibrated and put thru a test cycle, the unit tested good."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Simpsonville, SC 29680
Jerry D.
Job Details:
05/02/2023
"Found frost in freezer around door, found door to low and not sealing, installed shim wp487576 from truck stock, door seal now chks ok"
We serviced a
WHIRLPOOL DRYER
Model MED5630HC1
Near Piedmont, SC 29673
Jerry D.
Job Details:
05/02/2023
"Heater open, installed heater sent preid, cycled unit through test and heat relay ok, temps cycles are 109@197, unit ok, vent ok, customer paid total 428.00, cc , 3766923878"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRB322DMBM03
Near Pickens, SC 29671
Derek
Job Details:
05/02/2023
Found unit not defrosting. Cycled forced defrost. Unit says bi metal is open covered in ice. Cut off and bypassed bi metal. Still says open. Put original bi metal back onto unit. Control not reading correct status of bi metal. Will order. N15; ordrng 1 W11556926 (Ice maker) and 1 W11524469 (Control) and 1 WPW10128551 (Evap fan) and 1 W11524653 (Harness freezer)
We serviced a
JENN AIR RANGE
Model JDRP430HM00
Near Salem, SC 29676
Derek
Job Details:
05/02/2023
Installed parts and followed service pointer for inconsistent surface burner ignition. Burner lighting consistently. Also applied foam tape for back panel at cooling fan location for noise. Cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Easley, SC 29640
Cliff
Job Details:
05/02/2023
"Steve, 7736309270, found the splutch messed up again, Steve from techline wanted me to replace the gearcase and cam kit again, replaced parts, cycled unit, all functions check ok."
We serviced a
WHIRLPOOL WASHER
Model MVW7230HW0
Near Glenville, NC 28736
Frank
Job Details:
05/02/2023
Installed pump. Tested working ok
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Easley, SC 29640
Cliff
Job Details:
05/02/2023
"Found the shifter was stripped and would not change cam from spin to agitate, also the suspension is extremely loose, gave customer an estimate of 461.42 for both, they do not want repair at this time."
We serviced a
MAYTAG DRYER
Model MED5630HW2
Near Glenville, NC 28736
Frank
Job Details:
05/02/2023
Found unit thumping really bad.. rollers looked ok but replaced them and motor tested working ok. No more thumping
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Franklin, NC 28734
Kari
Job Details:
05/02/2023
Installed parts unit checks ok
We serviced a
JENN-AIR REFRIGERATOR
Model JS42NXFXDE01
Near Franklin, NC 28734
Kari
Job Details:
05/02/2023
"Took quick pics, found lights out in freezer and dim in fridge. Found this unit is under 5 year SCode: S84638 and will pay for parts and labor and unit is within 5 year time frame. Also found door not closing fully, it looks as if its shifted forward a bit. Called MA and asked him about the hinges and he said if this isnt the model with the shelves that slide, its not and I checked all the shelves to make sure they arent impeding the door closer, we will need to order the right side hinges, those are not covered by any warranty so I made the customer an estimate for hinges and a second man for ,045.81. Since the customer has a contract with a company that we arent contracted with, he will have to get approval before repairs are done. Ran CC for 25 and emailed receipt ; ordrng 4 W11632139 (Modules)s and 1 Makesurethere3lightsperbag and 1 W10691534 (Hinge bottom RH) and 1 Twoman (Two Man) and 1 ***DONOTORDERPARTSUNTILCUSTOMERGETS (APPROVAL*********) and 1 Q16 (Job code) and 1 NeedMAorDE (Need super for door)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Piedmont, SC 29673
Matt
Job Details:
05/02/2023
Customer stated unut doesn't dry. Has no heat. I put unit in diagnostics and found no error codes. Stated an auto test. All functions passed. Heater does heat. Unit is out of rinse aid and has a lot of suds left after the cycle. Recommend customer turn on all the options. Prime sink with hot water. Run a longer cycle. Use rinse aid and open the door of the dishwasher within 1 hour of cycle completion to keep water from re depositing on dishes.The longer cycle will ensure detergent has been rinsed away.Rinse aid will help sheet the water off the dishes so they are easier to dry.
We serviced a
WHIRLPOOL WASHER
Model MVW5430MW0
Near Franklin, NC 28734
Kari
Job Details:
05/02/2023
"Took quick pics, and documented pictures of unit leaking through wall and cabinet in hallway. Took pictures of the back of the washer where the hot hose has a slight drip because the hot hose looks like it was cross threaded and not tightened down enough to seal it fully. Put unit into diagnostics, found unit showing a 8-1 long fill code. Found there to be sediment in the cold fill screen. Corrected valve and hoses. Ran unit through diagnostic cycle. Unit completed with no additional codes. Unit checks ok. ; used 1 W11513255 (Valve) from stock"
We serviced a
KITCHENAID RANGE
Model KCGS556ESS05
Near Sylva, NC 28779
Kari
Job Details:
05/02/2023
Installed parts unit checks OK adjusted flame levels
We serviced a
WHIRLPOOL DOUBLE WALL OVEN
Model WOD51EC0HS20
Near Simpsonville, SC 29680
Matt
Job Details:
05/02/2023
"Replaced upper and lower door seals,inner door liner and hinges. Tested seals with paper test. Seals are sealing all the way around now. Pre heated ovens to 350 and customer cooked in oven. Checks o.k"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Simpsonville, SC 29680
Carl
Job Details:
05/02/2023
Difuser cracked and control wont adjust l14; ordrng 1 W11478200 (Control box) and 1 W11264792 (Diffuser) and 1 L14 (Labor)
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706EBS01
Near Sapphire, NC 28774
Frank
Job Details:
05/02/2023
At -5 setting. Reading 4.0 not making ice.at 35 setting at 38 degrees in rc 56 and 66 e0 no errors.. found ice top right corner defrosted.. checked door seal seems like bottom not sealing right when pushing on door it seals ok.. went back at 4pm checked temps running at 0 degrees in fc right now..made one batch of ice.. another batch ready to go customer will monitor and call back.. send freezer seal W10407215 and ice maker W11658802
We serviced a
WHIRLPOOL DISHWASHER
Model MDB4949SDM2
Near Sylva, NC 28779
Kari
Job Details:
05/02/2023
"Took quick pics, found unit door wont close, cabinet is leaning, took kickplate off, found the left front foot to be under the floor and the back wheels are still in the lowest position, pulled unit out, raised the wheels in the back, fixed support boards under unit to sit under feet properly, put unit back in counter and leveled front feet. Door now closes automatically. Customer paid 229.99 for TC and labor. Had office run cc and email receipt. Unit checks ok"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHW4
Near Sylva, NC 28779
Kari
Job Details:
05/02/2023
"Took quick pics, found unit showing 4-3 open motor code. Tested motor found 7.7 ohms tested board found 35 v going to motor but drain pump runs. Need board for repair ; ordrng 1 W11087226 (Control) and 1 N15 (Job code)"
We serviced a
WHIRLPOOL WASHER
Model MVW4505MW0
Near Cherokee, NC 28719
Kari
Job Details:
05/02/2023
"Took quick pics, found unit showing 5-4 lid not opened between cycles found the latch will just sit and click. Installed new latch. Ran diagnostic cycle. Unit completed. Unit checks ok ; used 1 W11513248 (Latch) from stock"
We serviced a
WHIRLPOOL WASHER
Model MHW5630HC3
Near Cherokee, NC 28719
Kari
Job Details:
05/02/2023
"Took quick pics, found unit showing f9e1 and the door wont unlock, cleared codes found drain pump doesnt even hum, took dryer down and tested continuity to drain pump, found the pump shows an OL. Drained all water, installed new pump. Ran through diagnostics. Unit now clears water. Unit checks ok. Double labor auth M16XB21AL2; used 1 W11458345 (Drain pump) from stock"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT518SZFM02
Near Gerton, NC 28735
Brian
Job Details:
05/02/2023
"Found door switch broken. Removed broken switch and found wires for switch foamed in place and not long enough to attach new switch. Contacted tech support and spoke to Chris. Once I had hi, on the phone, he had me attempt to pull wires out. When doing so, wires broke. Send him pictures and documented. Unit is non reparable. Unit will be sent for review and whirlpool will be in touch with me and/or customer. Sr number (7736309281)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHW06
Near Hendersonville, NC 28792
Brian
Job Details:
05/02/2023
"Installed new control, and harness and defrost sensor. Tested and found heater now coming on. At this time, all operations ok."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Laurel Park, NC 28739
Brian
Job Details:
05/02/2023
Installed new inlet valve and tightened handles. Tested and found water dispensing very slowly. Removed filter and found water pressure ok. Observed for leaks and found none. Info customer that they will need to get a new filter in order to have proper water pressure and proper ice production. Customer understood.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ00
Near Brevard, NC 28712
Brian
Job Details:
05/02/2023
Found freezer and top led modules out. Tested and found freezer led bad. New Module (W11601310) needed.; ordrng 1 W11601310 (Led) and 1 J13 (Job code)
We serviced a
MAYTAG DRYER
Model MEDB955FC0
Near Salem, SC 29676
Derek
Job Details:
05/02/2023
List of faults. F4E5 high temp limitF4E4 line voltage errorF4E3 restricted air flow F3E7 rear moisture sensor F6E2 communication errorUnit displayed L2 voltage error and shutdown. Unit has since ran cycles normally heating properly. Cleared errors. Cycled on high heat. Average temp 155° with a high of 177°. Good rise and fall rate of temps. Air flow decent. Unit has 246 v both checking with meter and showing in diagnostics test. Will order parts to repair. N15; ordrng 1 W11365798 (ACU)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ00
Near Taylors, SC 29687
Chris
Job Details:
05/02/2023
Installed new fan. Unit check is ok
We serviced a
AMANA WASHER
Model NTW4516FW3
Near Taylors, SC 29687
Chris
Job Details:
05/02/2023
Installed new parts. Unit check is ok a16x7x1nl2
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ05
Near Easley, SC 29642
Cliff
Job Details:
05/02/2023
"Found them switch in the off position, once I flipped it back on I was able to run ice maker through a cycle, it dumped ice and filled with water with no issues"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Easley, SC 29642
Cliff
Job Details:
05/02/2023
"Replaced part, waiting for compressor and fans to kick on, checked temp, my probe thermometer registered 38, all functions ok."
We serviced a
WHIRLPOOL DRYER
Model WED49STBW1
Near Taylors, SC 29687
Chris
Job Details:
05/02/2023
Unit has broken timer . Gave customer a bluebook estimate for repair at 488.17. Installed new parts. Unit check is ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDEM00
Near Taylors, SC 29687
Chris
Job Details:
05/02/2023
"Customer states unit had small puddle to right side of unit. Customer believes drip pan is leaking . Drip is on left side. Drip pan has Water and isnt leaking . Filled imk and energized imk solenoid ,no leaks. Ran several gallons of water through dispenser and no leak at ether valve. No leak from shut off valve . Unit has Refrigerant lines swearing and heavy Corrosion around compressor area as noted in pictures. Advised customer the process to attempt to fix this is install tap and dye pack which will require part,labor and refrigerant material estimate . customer denied further repair"
We serviced a
KITCHENAID REFRIGERATOR
Model KSRW25CRSS02
Near Lake Toxaway, NC 28747
Frank
Job Details:
05/02/2023
Found spout for water to maker was frozen. Defrosted tested working ok
We serviced a
WHIRLPOOL DISHWASHER
Model KDTM404KPS1
Near Greenville, SC 29607
Carl
Job Details:
05/02/2023
Inner door damaged and rack mounts will order l14; ordrng 1 W11098409 (Inner door) and 1 W11101573 (Rack mount) and 1 W11536439 (Rack mount) and 1 L14 (Labor)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Greenville, SC 29607
Carl
Job Details:
05/02/2023
Found supply line kinked adjusted and cycled imk to ck operation found good fill ck ok
We serviced a
KITCHEN AID RANGE
Model KSEG700ESS0
Near Greenville, SC 29607
Carl
Job Details:
05/02/2023
Cancled on phone
We serviced a
MAYTAG WASHER
Model MVW6500MBK0
Near Greenville, SC 29607
Carl
Job Details:
05/02/2023
Ran diagnostics and no error codes found belt worn installed new belt cycled unit to ck operation unit ck ok
We serviced a
JENN-AIR BUILT-IN M/W
Model JMDFS24JL00
Near Greenville, SC 29601
Flint
Job Details:
05/02/2023
"Replaced control, the unit tested good."
We serviced a
WHIRLPOOL RANGE
Model WGG745S0FS02
Near Greenville, SC 29617
Flint
Job Details:
05/02/2023
"Customer service number- 18002531301. File number 7736308850. Found bake ignitor in lower oven burnt out, replaced to test and the igniter, the unit tested good, called tech line and reported, then called partner team to get authorization for the the parts and labor so the customer would not have to pay for the repair. Partner team stated they will check with the replacement team, but the tech line stated it could be fixed . The unit tested good at this time. 7733991278 service request number."
We serviced a
KITCHEN AID ICE MACHINE
Model KUIX305ESS1
Near Spartanburg, SC 29307
Tyler
Job Details:
05/02/2023
"Found unit won't fill with water with filter. Took out filter, fills. Water level sensor/pump is bad. Gave estimate for 477.82. Collected 238.91 via check.; ordrng 1 W11542867 (Pump) and 1 L14jobcode (L14 job code)"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFHS2611LWMA
Near Boiling Springs, SC 29316
Tyler
Job Details:
05/02/2023
"Found drain tube clogged. Cleared drain, all functions tested good. Collected 209.90 via check."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF989SDAF00
Near Boiling Springs, SC 29316
Tyler
Job Details:
05/02/2023
"Found dual valve leaking. Pulled water line out, reinserted line. Actuated valve, still had a drop forming. Gave estimate for 36.70. Collected full amount via card.; ordrng 1 WPW10341329 (Water valve)"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706ESS05
Near Inman, SC 29349
Tyler
Job Details:
05/02/2023
"Customer states unit making loud noise. Had a video of noise. Tested unit in diagnostics, all functions tested good. Could not pinpoint any abnormal noises. Customer could not hear the same noise during testing."
We serviced a
WHIRLPOOL DRYER
Model WED4850HW0
Near Inman, SC 29349
Tyler
Job Details:
05/02/2023
"Dryer was pulled out on arrival. Customer states unit taking to long to dry. Checked all functions, all functions tested good. No restrictions in airflow going outside. Vent may have been pinched."
We serviced a
FRIGIDAIRE OVEN
Model COULD NOT FIND
Near Greenville, SC 29607
Carl
Job Details:
05/02/2023
Cound not find model # and customer is having display issues unit is 20 yrs old
We serviced a
KITCHENAID REFRIGERATOR
Model KSF26C4XYW03
Near Lyman, SC 29365
Tyler
Job Details:
05/02/2023
Customer states temp are a little warm. Checked all functions in diagnostics. All functions tested good. Temp was around 10 degrees in FC. Condenser coils were dirty. Cleaned coils and set temp to -2 degrees in FC. Collected 25.00 via card.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ04
Near Duncan, SC 29334
Tyler
Job Details:
05/02/2023
Found RC section wArm. Evap motor not working. All other functions tested good.; ordrng 1 W11578030 (Evap motor) and 1 W11224256 (Control) and 1 Q16jobcode (Q16 job code)
We serviced a
MAYTAG WASHER
Model MVW7230HC0
Near Taylors, SC 29687
Derek
Job Details:
05/01/2023
F0E3 overload and F0E7 load present during clean cycle. Customer has never ran clean cycle. Cycled test mode. Slider moving freely during test. Half way thru testing unit stopped performing all test on command but sat doing nothing when prompting. UI dial has failure and is running cycle thats not been selected. Very loud knocking sound present when agitating with actual load. Will order parts. N15; ordrng 1 W11478526 (Panel) and 1 W11419171 (ACU) and 1 W11419171 (Gear case)
We serviced a
KITCHEN AID REFRIGERATOR
Model KSC24C8EYY02
Near Travelers Rest, SC 29690
Flint
Job Details:
05/01/2023
Found fan blade has busted and fallen off the motor shaft. ; ordrng 1 W10156818 (Blade) and 1 WP2188874 (Motor)
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRMF706ESS05
Near Starr, SC 29684
Jerry D.
Job Details:
05/01/2023
"Fan motor noise,ordering, Q16; ordrng 1 W10799016 (Motor) and 1 W10833801 (Motor) and 1 Q16 (Q16)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ00
Near Anderson, SC 29625
Jerry D.
Job Details:
05/01/2023
"Housng broken, ordering, j13; ordrng 1 W10817430 (Housing) and 1 W10306392 (Cover)"
We serviced a
WHIRLPOOL FREEZER
Model WRF767SDHZ00
Near Anderson, SC 29625
Jerry D.
Job Details:
05/01/2023
"Installed module sent preid, cycled unit through test and all functions are working properly"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Inman, SC 29349
Chris
Job Details:
05/01/2023
Installed new parts. Unit check is ok
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Inman, SC 29349
Chris
Job Details:
05/01/2023
Unit dies mid cycle . Unit has f1 fault. Ordering for repair ; ordrng 1 W11603810 (Control) and 1 W11428524 (Capacitor Capacitor) and 1 W10890624 (Motor) and 1 W10903238 (Harness) and 1 L14
We serviced a
JENN-AIR RANGE
Model JGS9900CDS02
Near Inman, SC 29349
Chris
Job Details:
05/01/2023
Installed new parts. Unit check is ok
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF707ESS01
Near Greer, SC 29650
Chris
Job Details:
05/01/2023
Fresh food evaporator is frozen over. Unit has bowed drain pan. Service pointer w11092686 recommends new drain pan and fresh food wire harness. Gave customer a bluebook estimate for repair at 613.49; ordrng 1 Q16 and 1 W11457241 (Pan)
We serviced a
WHIRLPOOL DRYER
Model WED4850HW0
Near Piedmont, SC 29673
Frank
Job Details:
05/01/2023
Installed parts tested working ok
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Greenville, SC 29605
Cliff
Job Details:
05/01/2023
"It seems that the cabinet is what is squeaking, tired calling techline but they were down for training, will try again.; ordrng 1 Needtocalltechline (Needtocalltechline)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFC704FPS04
Near Greenville, SC 29609
Cliff
Job Details:
05/01/2023
"Replaced parts, add sure the compressor and fans kicked on, cycled ice maker, all functions check ok.; used 1 L14 job code (L14 job code) from stock"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT112CZJZ00
Near Greenville, SC 29611
Cliff
Job Details:
05/01/2023
"Replaced parts, weighed in 1.44 oz of R600, unit began to cool down, advised customer to watch unit for one week."
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Greenville, SC 29615
Cliff
Job Details:
05/01/2023
"Replaced parts, cycled unit, all functions check ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHW08
Near Greenville, SC 29615
Chris
Job Details:
05/01/2023
Installed new parts. Unit check is ok
We serviced a
MAYTAG WASHER
Model MVWC565FW3
Near Travelers Rest, SC 29690
Flint
Job Details:
05/01/2023
"Replaced belt, cam, actuator and capacitor, recalibrated the unit and put through a test cycle, the unit tested good.; used 1 W11239857 (Belt) from stock"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Seneca, SC 29672
Frank
Job Details:
05/01/2023
"Unit pulled out on arrival.. pump humming getting 120v.. changed pump tested working ok,."
We serviced a
AMANA WASHER
Model NTW4516FW3
Near Anderson, SC 29625
Jerry D.
Job Details:
05/01/2023
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Fair Play, SC 29643
Jerry D.
Job Details:
05/01/2023
"Timer is noisey thermostat is short cycling, ordering, Q16; ordrng 1 Q16 (Q16) and 1 W10185982 (Timer) and 1 3977767 (Thermostat)"