We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ15
Near Leicester, NC 28748
Matt
Job Details:
06/07/2023
Evacuated system. Replaced compressor and installed u.v dye drier. Pressure tested unut with nitrogen. No leaks unit held pressure. Pulled a long vacuum. Also installed new wire harness. Weighed in 1.87ounces of r600a checks o.k
We serviced a
AMANA WASHER
Model NTW4516FW3
Near Inman, SC 29349
Tyler
Job Details:
06/07/2023
Called TECHLINE spoke to Rob. SR: 7736577287. Customer wants me to write is down as unrepairable even after TECHLINE confirmed customer is putting too much detergent in unit.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ02
Near Columbus, NC 28722
Brian
Job Details:
06/07/2023
"Installed new inlet valves. Tested water dispenser and ice maker and found all operations ok at this time, with no leaks detected."
We serviced a
WHIRLPOOL RANGE
Model WFE525S0JS3
Near Columbus, NC 28722
Brian
Job Details:
06/07/2023
Found bake and broil elements not coming on. Found control sending voltage but voltage isnt making it to elements. Control (W11594188) and harness (W11452622) needed. ; ordrng 1 W11594188 (Control) and 1 W11452622 (Harness) and 1 N15 (Job code)
We serviced a
WHIRLPOOL WASHER
Model WFW92HEFC0
Near Columbus, NC 28722
Brian
Job Details:
06/07/2023
"Found f8e3 (overflow condition) F3e1 (water level system error). Ran unit through auto diagnostics and found unit completing without issues. Pressure system seems ok. Unit is draining and spinning properly at this time. Found excess suds in unit. Changed concentration to a higher setting and changed water to hard. Explained to customer the importance of this. At this time, all operations ok with no leaks detected."
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Lake Lure, NC 28746
Brian
Job Details:
06/07/2023
"Installed new gearcase and cam and belt. Tested unit observing for leaks and proper functions. At this time, all operations ok with no leaks detected."
We serviced a
WHIRLPOOL DRYER
Model WED9550WL1
Near Asheville, NC 28805
Kari
Job Details:
06/07/2023
"Took quick pics found unit showing an F 70 code which is the electronics. Cannot hear each other found that if you let unit run, then it will eventually blank out the display and then you have to wait for it to reset itself to be able to enter back into a drying cycle. Couldnt give customer estimate because both boards are no longer available collected 50 trip. Charge an emailed receipt."
We serviced a
KITCHEN AID DISHWASHER
Model KDTM354DSS4
Near Asheville, NC 28804
Kari
Job Details:
06/07/2023
Installed Parts ran unit through diagnostic test and turn the heater on all functions. Check OK
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Easley, SC 29642
Cliff
Job Details:
06/07/2023
"Found the agitator bolt had come loose, there was no thread lock on bolt, added thread lock and installed agitator, ran a calibration and auto test, all functions check ok"
We serviced a
WHIRLPOOL WASHER
Model WFW70HEBW0
Near Asheville, NC 28804
Kari
Job Details:
06/07/2023
"Took quick pics customer states that unit is making a squeak more so in the agitation than in the spin cycle unit did have some codes, stored some related to the drain some related to the film and then a load in the washer and clean washer cycle which could also be indicative of bearings being weak ran unit through every test in every cycle I could could not duplicate squeak. Also had customer put a large blanket into the drum to see if we could duplicate it with some weight in the basket and still could not duplicate issue. Told customer if she could get it on a video and call us back then maybe we can pinpoint where the noise is coming from but as of right now all functions look good in unit checks OK"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFC704FPS04
Near Taylors, SC 29687
Cliff
Job Details:
06/07/2023
"Replacing just the ice maker today, the total for ice maker minus the TC is 382.44. I asking customer to give it a couple of weeks to see if ice keeps clumping or if the new ice maker fixes the issue, if it does fix it we will need to give a refund of 116.50. Waiting to hear back from customer ; ordrng 1 Waitingtohearfromcustomer (Waitingtohearfromcustomer)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF540PADM3
Near Simpsonville, SC 29681
Carl
Job Details:
06/07/2023
Ran diagnostics and Found connector off at the element reinstalled ran diagnostics again unit ck ok
We serviced a
MAYTAG WASHER
Model MVW6230RHW2
Near Inman, SC 29349
Chris
Job Details:
06/07/2023
Unit has Multiple F7 faults. Capacitors disconnected from gear case and laying inside of belt guard. installed new parts . New f7 e4 fault appeared. Unit needs shifter and gearcase. Ordering for repair ; ordrng 1 W11449840 (Gearbcase) and 1 W11481722 (Shifter) and 1 N15
We serviced a
WHIRLPOOL COOKTOP
Model WCG97US0HS00
Near Simpsonville, SC 29680
Jerry D.
Job Details:
06/07/2023
"Found right front burner gas tube nut loose, tightened all fittings, restored gas valve, no leaks found unit checks ok"
We serviced a
MAYTAG DRYER
Model MGD6230HW0
Near Inman, SC 29349
Chris
Job Details:
06/07/2023
Unit has vent restriction faults stored. Customer advised error message appeared a week ago and unit began to fail. Unit heats as designed. Went underneath deck and demonstrated/showed customer no air flow from vent. Inserted probe at dryer vent. Unit reached 220 degrees and cycled off. Recommended customer have vents cleaned professionally. Called tech line and spoke with Adrian. Adrian advised to have vents professionally cleaned. Unit works as designed. File number for call is 7736581263
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Simpsonville, SC 29680
Jerry D.
Job Details:
06/07/2023
"Pump inoperable, ordering, j13; ordrng 1 W11164469 (Sump assy)"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Greer, SC 29650
Chris
Job Details:
06/07/2023
Unit has extremely loud squeal from gearbox. Replaced from stock. Unit check is ok . W17cp50xpl2
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Piedmont, SC 29673
Jerry D.
Job Details:
06/07/2023
"Temps 36@1, Valve inoperable, installed wpw10498990 from truck stock, cycled unit through test and no leaks found fill ok"
We serviced a
JENN-AIR OVEN
Model JGW8130DDB
Near Greer, SC 29651
Chris
Job Details:
06/07/2023
Installed new parts. Unit check is ok
We serviced a
KITCHEN AID DISHWASHER
Model KDTE334GPS0
Near Westminster, SC 29693
Frank
Job Details:
06/07/2023
Leaking front left by the door. Seal looks worn. Everything else looks ok.; ordrng 1 KDTE334GPS0 (Tub gasket) and 1 Jobcodej13 (Job code j13)
We serviced a
FRIGIDAIRE DISHWASHER
Model FFID2423RS4B
Near Simpsonville, SC 29681
Flint
Job Details:
06/07/2023
"Found the board not sending power down to the heater, would need board, estimate is 587, the customer will look around"
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Westminster, SC 29693
Frank
Job Details:
06/07/2023
Shipping bolt s were not taken out.. took out shipping bolts tested cycle working ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WSF26C3EXW01
Near Fountain Inn, SC 29644
Flint
Job Details:
06/07/2023
"Found some ice, but no water in ice maker, replaced ice maker and ran through a harvest cycle, the unit filled and tested good."
We serviced a
WHIRLPOOL DISHWASHER
Model KDTM404EBS1
Near Piedmont, SC 29673
Jerry D.
Job Details:
06/07/2023
"Pump broken, estimate, 789.00, customer paid 150.00 cc ,3902642986"
We serviced a
WHIRLPOOL WASHER
Model WTW5015LW0
Near Anderson, SC 29626
Jerry D.
Job Details:
06/07/2023
"Overflow code, Drain pump overheated ,installed pump sent preid, cycled test,cntrl relay clicking loud and rapidly, inoperable, volts and polarity good, ordering, j13; ordrng 1 W11428994 (Cntrl) and 1 W11335100 (Harness) and 1 W11162560 (Capacitor) and 1 W10677723 (Motor)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Greer, SC 29651
Chris
Job Details:
06/07/2023
Unit has shorted was motor. Ordering for repair ; ordrng 1 W11665769 (Sump assembly) and 1 L14
We serviced a
WHIRLPOOL WASHER
Model NTW4516FW3
Near Anderson, SC 29624
Jerry D.
Job Details:
06/07/2023
"Splutch grinded down, installed w10721967 from truck stock cycled unit through test and all functions are working properly"
We serviced a
WHIRLPOOL REFRIGERATOR
Model jffcc72efs00
Near Seneca, SC 29678
Frank
Job Details:
06/07/2023
20 degrees in fc. Rc 41.. ice build up on fc back wall.. frost on sides.. ran diagnostics ice maker and water ok.. going to need to defrost freezer EVAP; ordrng 1 W11204566 (Harness with thermistor) and 1 W10316760 (Thermistor) and 1 W11585972 (Door gasket) and 1 Jobcodeu18 (Job cod3 u18)
We serviced a
AMANA RANGE
Model AER6303MFB5
Near Anderson, SC 29624
Jerry D.
Job Details:
06/07/2023
"Installed listed parts sent preid, cycled unit through test and unit checks ok"
We serviced a
KITCHEN AID/A REFRIGERATOR
Model KSRG25FKSS17
Near Seneca, SC 29672
Frank
Job Details:
06/07/2023
Rc at 40 degrees fc at -3 set to normal.. shutting off creating warm temps in rc.. replacing control as per service pointer. Back Light not working on assembly cover. Showing up not available..; ordrng 1 WPW10366605 (Control board) and 1 Jobcodel14 (Job code l14) and 1 2220092b (Front cover assembly)
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS03
Near Lyman, SC 29365
Tyler
Job Details:
06/07/2023
Found compressor locked up. Ordering all necessary parts and sealed system tech.; ordrng 1 W11574734 (Compressor) and 1 W11504431 (Couple) and 1 W11504415 (Coupler) and 1 W11506621 (Coupler) and 1 W11506635 (Couler) and 1 W11506635 (Port) and 1 Wpw10143759 (Dye drier) and 1 Nitrogen (Nitrogen) and 1 R600 (R600) and 1 X20jobcode (X20 job code) and 1 Sealedsystemtech (Sealed system tech)
We serviced a
WHIRLPOOL REFRIGERATOR
Model n/a
Near Seneca, SC 29672
Frank
Job Details:
06/07/2023
Ice building up on back wall air leak. Quoted 406.79 paid 200.00 ck. Owes 206.79; ordrng 1 W10407215 (Door gasket freezer) and 1 Jobcodel14 (Job code l14)
We serviced a
MAYTAG WASHER
Model MVWC565FW1
Near Duncan, SC 29334
Tyler
Job Details:
06/07/2023
"F2e1, f0e5 errors. Basket is loose, bad drive hub. Gave estimate for 297.98. Collected 148.99 via card.; ordrng 1 W10528947 (Hub) and 1 F12jobcode (F12 job code)"
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Easley, SC 29642
Derek
Job Details:
06/07/2023
Helped CH. Unit checks ok.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM08
Near Boiling Springs, SC 29316
Tyler
Job Details:
06/07/2023
"Installed part, tested for operation. All functions tested good."
We serviced a
WHIRLPOOL WASHER
Model n/a
Near Greer, SC 29650
Derek
Job Details:
06/07/2023
Found unit leaking intermittently. Water under control panel under valve and dripping from under side of valve at the fabric softener solenoid. Gave est for new valve and housing of Customer okd estimate. Will order part. ordrng 1 W11173597 (Valve housing)
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Greer, SC 29651
Derek
Job Details:
06/07/2023
Installed parts. Cycled unit. Unit checks ok policy adjust is W17CVX1NL2
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ04
Near Simpsonville, SC 29681
Carl
Job Details:
06/07/2023
Installed new motor and yolk unit ck ok
We serviced a
WHIRLPOOL DISHWASHER
Model n/a
Near Mauldin, SC 29662
Carl
Job Details:
06/07/2023
Found float switch stuck got fill and want to drain impeller just spins on shaft l14; ordrng 1 W10876537 (Drain pump) and 1 L14 (Labor)
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Inman, SC 29349
Tyler
Job Details:
06/07/2023
"Installed parts, tested for operation. All functions tested good. Recalibrated and leveled unit."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHW06
Near Mauldin, SC 29662
Carl
Job Details:
06/07/2023
Installed new imk cycled to ck operation unit ck ok good fill
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Fountain Inn, SC 29644
Flint
Job Details:
06/07/2023
Found a defective timer and warped element. Grounded unit. 7736581498 file number from tech line. Safety team file number 7736523607. Safety team gave us trip and diagnostic authorization w17d191wl1 and stated they will reach out to the customer with a resolution.
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS0
Near Weaverville, NC 28787
Kari
Job Details:
06/07/2023
Took a quick pics found unit starts heats and works OK that was an old complaint from the customer first moved into the house. The builder is correct and that the issue is the unit is missing the turntable ring. The trolley that holds the plate will need that for repair.; ordrng 1 W11252182 (Turntable trolley) and 1 F12 (Job code)
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Fountain Inn, SC 29644
Flint
Job Details:
06/07/2023
"Had customer run a load before arriving, no water. Ran through the diagnostic cycle again and no water streaks inside unit, on the outside, under he cold water and in front under door boot area. Filled unit up several inches above the glass and boot and it started leaking out the door at the base. Found water coming out from the door. Cleaned up around where the seal meets the glass, unit tested good"
We serviced a
JENN-AIR RANGE
Model JGS9900BDB
Near Weaverville, NC 28787
Kari
Job Details:
06/07/2023
"Two quick pics found unit does not light in the bake cycle but the igniter glows ran The broil, broil cycle does come on And lights with gas. Found in the text sheet that the amps should be between 3.2 and 3.6 on both the igniters and when you were in the bag igniter its only about 2.2 2.3 A found 120 V going to igniter also found safety valve had resistance on each side would need Igniter for repair also found downdraft making a scraping noise and it gets worse the higher the setting made customer Customer agreed and paid half which the office ran card and emailed receipt. Customer will owe. ordrng 1 L14 (Job code) and 1 Wpw10201322 (Blower motor) and 1 W11596211 (Bake igniter) and 1 WPY707985 (Wheel dd)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model n/a
Near Greenville, SC 29615
Chris
Job Details:
06/07/2023
Unit has r134 leak. All fans work. No frost pattern on ether coil fresh food and freezer evap. Advised customer dye pack and tap would need to be installed with labor and refrigerant fee. After that additional parts and labor will be required after dye Circulates through system . Customer denied repair
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Greer, SC 29651
Carl
Job Details:
06/07/2023
Found thurmal open will collect on return ; ordrng 1 W11650662 (Heater)
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Marshall, NC 28753
Kari
Job Details:
06/07/2023
"Took quick pics, found unit showing seven one code which is no heat. Ran unit through diagnostic cycle them and it turns on the motor and drains properly but the heater never gets hot. Found heater showing zero ohms but the control is sending down 120 V when its supposed to and the drain pump has 38.6 ohms which is right in range will need heater for repair; ordrng 1 W10518394 (Heater) and 1 J13 (Job code)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Simpsonville, SC 29681
Carl
Job Details:
06/07/2023
Rollers on adjuster broke j13; ordrng 1 W10712395 (Adjuster kit) and 1 J13 (Labor)
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Alexander, NC 28701
Kari
Job Details:
06/07/2023
"Took quick pics, found unit showing long fill no fill code found units cold screen filled with mud and first. Installed new valve and advised customer put a secondary filter on cold incoming hose to prevent this from happening again because I let it fill a deep water heavy duty cycle and after that the new screen also had dirt in it. I did tell customer this will be a continuous issue until there is a secondary filter or the well is corrected ; used 1 W11210463 (Fill valve) from stock"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS00
Near Simpsonville, SC 29681
Carl
Job Details:
06/07/2023
Ran diagnostics fou no voltage from control or led board advised customer of issue and is not going to repair unit
We serviced a
WHIRLPOOL DISHWASHER
Model MDB9959SKZ0
Near Canton, NC 28716
Kari
Job Details:
06/07/2023
"Took quick pics found unit not draining found Unit showing an F9 E1 error code cleared code. Get the cancel button to make unit going to drain cycle doesnt even sound like the drain pump is humming when you touch it you can feel a little bit of a vibration but its not moving any water and the drain hose half looks dry vacuumed out all the excess water took drain pump down and found that the chopper had broken him and crack the impeller installed new Pump also found this unit is under the cereal break for the deteriorating heater bushings installed new heater ran unit through diagnostic cycle unit didnt leak and it completed all functions unit checks OK; used 1 W11497943 (Drain pump), and 1 W11537778 (Heater) from stock"
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Spartanburg, SC 29307
Tyler
Job Details:
06/06/2023
Unit not unlocking sometimes. Lid glass coming apart.; ordrng 1 W11413336 (Lid)
We serviced a
WHIRLPOOL RANGE
Model KFGG504KPS3
Near Franklin, NC 28734
Kari
Job Details:
06/06/2023
"Took quick pics, found unit showing no codes, ran unit through diagnostic test found unit had no codes stored. Wrapped my thermo coupler in tin foil 5 times according to the service pointer and took 6 temps. Found unit preheated in about 12 minutes. Ran bake cycle to 350 after 6 temps, it averaged out to 333.5 degrees. Calibrated up 25 degrees and reran bake cycle to 350 and took 6 temps. Now unit averages at 355.6 which is now in range. Unit checks ok"
We serviced a
WHIRLPOOL RANGE
Model WFG515S0JS0
Near Taylors, SC 29687
Chris
Job Details:
06/06/2023
Unit has shorted bake ignitor.
We serviced a
MAYTAG FREEZER
Model MZF34X20DW00
Near Greenville, SC 29611
Cliff
Job Details:
06/06/2023
"Found evaporator frozen over, checked defrost function in diagnostics, which it works ok. The thermistor topped out at 10.45 kohms while dipped in ice, the thermistor was a little loose on the tubing, so I repositioned on tubing then I taped and zip tied to keep it from coming loose. Total for today will be 238.75. Did advise to watch for a couple of weeks and to call back within 30 days if they see any ice build up, if they call back needing the control the total owed will be 498.08"
We serviced a
WHIRLPOOL WASHER
Model MVW5430MW0
Near Asheville, NC 28803
Matt
Job Details:
06/06/2023
Ran unit through diagnostics and found no error codes. Unit continues to run in rinse and does not complete cycle. Will order control.; ordrng 1 W11627413 (Control) and 1 J13jobcode (J13 job code) and 1 Anytech (Any tech)
We serviced a
WHIRLPOOL RANGE
Model WFE505W0JZ3
Near Taylors, SC 29687
Chris
Job Details:
06/06/2023
Installed new parts. Unit check is ok
We serviced a
MAYTAG DRYER
Model MEDC465HW0
Near Greer, SC 29651
Chris
Job Details:
06/06/2023
Installed new roller kit. Unit check is ok
We serviced a
KITCHEN AID OVEN
Model KSDB900ESS3
Near Asheville, NC 28803
Matt
Job Details:
06/06/2023
Found bake element open. Blue book estimate is 326.00 total. Customer approved and is paying half today 163.00 and 163.00 when part is installed.; ordrng 1 W10774342 (Bake element) and 1 F12jobcode (F12 job code) and 1 Anytech (Any tech)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Greenville, SC 29607
Cliff
Job Details:
06/06/2023
"Found water line in back was split, cut bad section out and installed a fitting, cycled dispenser to check for leaks and operation, also the damper is noise when opening and closing, will order; ordrng 1 W11236851 (Damper) and 1 J13jobcode (J13 job code)"
We serviced a
MAYTAG DRYER
Model MEDC215EW1
Near Arden, NC 28704
Brian
Job Details:
06/06/2023
Found timer not advancing. Also found rollers and belt worn out. Inspected and found Timer (WPW10185982) and repair kit (4392067) idler pulley (WP691366) in need of replacement. ; ordrng 1 WPW10185982 (Timer) and 1 J13 (Job code) and 1 4392067 (Repair kit) and 1 WP691366 (Idler pulley)
We serviced a
MAYTAG WASHER
Model MHW4200BW0
Near Hendersonville, NC 28791
Brian
Job Details:
06/06/2023
"Installed new bellow. Tested unit observing for leaks and proper functions. At this time, all operations ok with no leaks detected. Collected 129.99 for labor."
We serviced a
MAYTAG WASHER
Model MVWC565FW3
Near Greenville, SC 29607
Cliff
Job Details:
06/06/2023
"Found the black wire on motor harness open, ordering parts.; ordrng 1 W11545744 (Lower harness) and 1 W11611306 (Control) and 1 N15jobcode (N15 job code)"
We serviced a
WHIRLPOOL OVEN
Model KSGG700ESS2
Near Asheville, NC 28803
Matt
Job Details:
06/06/2023
Put unit in diagnostics and tested both fans. Both fans pass in diagnostics. Tested in convection bake and all functions pass.
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Zirconia, NC 28790
Derek
Job Details:
06/06/2023
Installed motor pump. Cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL WASHER
Model MVW5430MW0
Near Greer, SC 29651
Chris
Job Details:
06/06/2023
"Customer states unit gets off balance and begins to walk when in spin. Customer has very small load present at time of service.unit has no stored faults. Unit performs and competes diagnostic cycle as designed. Hoses slap back of machine. Zip tied hoses Unit is level ,firm and planted . Suspension checks ok . Service pointer w11617330 addresses customer complaint. Went over service pointer with customer . Customer is unsatisfied with unit. Customer wants unit replaced .Called techline and spoke with Kurt. Unit works as designed. Customer will have to follow service pointer instructions. Unit check is ok. File number for call is 7736569690"
We serviced a
KITCHEN AID DOWN DRAFT
Model n/a
Near Greer, SC 29650
Chris
Job Details:
06/06/2023
Unit is a down draft . No mention or customer mentioning of clogged vent. Unit is stuck in upward position. Switch check ok .found screens installed incorrectly. Installed screens correctly. Unit no checks ok .
We serviced a
WHIRLPOOL RANGE
Model KFED500ESS03
Near Greer, SC 29650
Chris
Job Details:
06/06/2023
Took pics and dropped off parts per notes. Cant reach customer pay phone
We serviced a
KITCHEN AID RANGE
Model KSDB900ESS4
Near Greer, SC 29650
Chris
Job Details:
06/06/2023
Work order has been sent over with wrong engineering digit. unit was floor model unit has wrong burner heads and caps . Ordering for repair ; ordrng 1 W11367105 (Burner heads) and 1 W11443594 (Kit) and 1 W11605764 (Kit) and 1 W10898387 (Ignitor) and 1 W11643126 (Ignitor) and 1 L14
We serviced a
WHIRLPOOL DISHWASHER
Model WDT705PAKZ0
Near Walhalla, SC 29691
Frank
Job Details:
06/06/2023
Installed vent. Tested working ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ0
Near Greenville, SC 29609
Flint
Job Details:
06/06/2023
"Found shorted ui f6e1 error, replaced ui and the unit tested good"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Greenville, SC 29609
Flint
Job Details:
06/06/2023
"Found belt had come loose and wrapped around the motor shaft, replaced the belt and put into a test cycle, the unit tested and good."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315Sdhm04
Near Powdersville, SC 29673
Jerry D.
Job Details:
06/06/2023
"Recoverd approximately 3 oz of refrigerant, installed listed parts, pulled 30 inches of vaccum, vaccum is holding, charged 4.6 oz, lowside 3 psi, good frost pattern on evaperator and temps are coming down rapidly, unit chks okay"
We serviced a
WHIRLPOOL WASHER
Model WTW8500DC5
Near Greenville, SC 29611
Flint
Job Details:
06/06/2023
"Replaced ui and put into a test cycle, the unit went through all the functions, it tested good."
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Simpsonville, SC 29681
Flint
Job Details:
06/06/2023
"Found bolt holding stator and rotor in place had fallen out, put loc-tite on screw and screwed back in tight, ran through a spin mode several times and checked the bolt again, the unit tested good."
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Simpsonville, SC 29681
Flint
Job Details:
06/06/2023
"Found fresh food evaporator thermistor out of specs, needs fresh food fan assembly. Estimate is 552. ; O-emld tckt"
We serviced a
WHIRLPOOL OVEN
Model KSGB900ESS4
Near Fountain Inn, SC 29644
Jerry D.
Job Details:
06/06/2023
"Customer did a reset and unit is working now, cancelled"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM08
Near Fountain Inn, SC 29644
Jerry D.
Job Details:
06/06/2023
"Evaperator fan motor inoperable, installed motor sent preid, cycled unit through test and unit checks okay"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Fountain Inn, SC 29644
Jerry D.
Job Details:
06/06/2023
"Fresh evaperator frozen wires burnt no power from cntrl, ordering, j13; ordrng 1 W11321510 (Cntrl) and 1 W11573116 (Assy harness)"
We serviced a
WHIRLPOOL RANGE
Model WFG320M0BS3
Near Simpsonville, SC 29680
Jerry D.
Job Details:
06/06/2023
"Burners and caps do not fit properly, ordering, j13; ordrng 2 W10183368 (Caps)s and 1 W10183369 (Cap) and 1 W10183370 (Cap) and 2 W10515455 (Burners front)s and 1 W10515454 (Burner) and 1 W10515453 (Burner)"
We serviced a
MAYTAG WASHER
Model MVWB765FW3
Near Simpsonville, SC 29680
Jerry D.
Job Details:
06/06/2023
"Was unable to separate tub and basket, shaft is corroded to tub, also dampers are worn out, installed agitator, ordering, Q16; ordrng 1 Q16 (Q16) and 1 W11134159 (Drive) and 1 W11226784 (Damper) and 1 W10512161 (Tub) and 1 W11089264 (Filter)"
We serviced a
WHIRLPOOL WASHER
Model MHW5630HC3
Near Zirconia, NC 28790
Derek
Job Details:
06/06/2023
F3E2 open or shorted ntc error. Installed harness but ntc wires are both black and none if the wires in harness labeled ntc harness match true wires on unit. On unit ntc wires are included in lower harness. Ntc shows 25 ohms. Will order parts to repair. N15; ordrng 1 W11557918 (Lower harness) and 1 W11550649 (ACU) and 1 W11314664 (Ntc)
We serviced a
MAYTAG WASHER
Model MVWX655DW1
Near Simpsonville, SC 29681
Carl
Job Details:
06/06/2023
Installed new spluch and belt ran diagnostics and a test cycle to ck operation unit ck ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW02
Near Greenville, SC 29615
Cliff
Job Details:
06/06/2023
Did not have right receipt
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM01
Near Simpsonville, SC 29681
Carl
Job Details:
06/06/2023
"Recovered 5.5 oz r134a removed compressor,evap and dry filter installed new compressor ,evap and dry filter installed 5.5 0zr134a cycled unit on and started to come down in temp unit ck ok"
We serviced a
WHIRLPOOL WASHER
Model MVW6230HW3
Near Greenville, SC 29615
Cliff
Job Details:
06/06/2023
"Found unit would not spin, just the agitator would spin. Also when I would cancel cycle the unit would continue trying to spin, I would have to unplug unit to get it to stop. The gearcase bad and at some point whenever I would power unit back on the canceling cycle message would appear and would not let me do anything else, ordering control.; ordrng 1 W11624938 (Control) and 1 W11449840 (Gearcase) and 1 W11590868 (Lower harness) and 1 U18jobcode (U18 job code)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Simpsonville, SC 29681
Flint
Job Details:
06/06/2023
"Replaced parts, put through a test cycle and the heater and unit tested good."
We serviced a
WHIRLPOOL M/W OTR
Model WMH78519LZ00
Near Greenville, SC 29617
Cliff
Job Details:
06/06/2023
"Customer explained to me that someone has agreed to replace the unit and does not want me to paint the black mark inside cavity. I talked to Chris from techline, 7736451006, got it documented with them they she refused repair."
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Zirconia, NC 28790
Derek
Job Details:
06/06/2023
Installed parts and cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMW0
Near Asheville, NC 28805
Matt
Job Details:
06/06/2023
Put unit in diagnostics and found no error codes. Ran auto test. All functions pass.
We serviced a
WHIRLPOOL WASHER
Model MHW6630HC0
Near Asheville, NC 28804
Matt
Job Details:
06/06/2023
"Put unit in diagnostics and found error codes F0E2,F5E2,F8E1,F0E5,( oversuds,lock failure,valve failure,off balance load) started a test cycle and unit added water and drained.Control just clicks. Will nit energize motor at all. Blue book estimate to replace valves,control and lock is 1475.00 Customer checking options."
We serviced a
WHIRLPOOL MICROWAVE
Model WMH32519HV5
Near Candler, NC 28715
Matt
Job Details:
06/06/2023
Installed new control. Control had no display. Found transformer on new control damaged. Will re order.; ordrng 1 L14jobcode (L14 job code) and 1 W11342846 (Control) and 1 Customerwantstopreschedule (Customer wants to pre schedule)
We serviced a
MAYTAG M/W OTR
Model MMV1175JZ0
Near Brevard, NC 28712
Derek
Job Details:
06/06/2023
Installed magnetron and cycled unit. Unit pulling 15+ amps and heating. Unit checks ok.
We serviced a
WHIRLPOOL WASHER
Model MVWC565FW3
Near Franklin, NC 28734
Kari
Job Details:
06/06/2023
"Took quick pics, found unit wouldnt move past wash, found unit showing an 8-1 long fill code. Cleared sediment from screen and ran through a recalibration. Ran unit through spin manually found it sounds louder than it should. Tipped unit back and found gearcase oil in the shield. Will need parts for repair ; ordrng 1 W11454734 (Gearcase) and 1 W10721967 (Cam) and 1 N15 (Job code) and 1 Okanytech (Ok any tech)"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF507ESS01
Near Seneca, SC 29672
Frank
Job Details:
06/06/2023
Getting air leak in back of ice maker assembly causing freezing water line and ice buildup in front. Rear gasket 11.67. 30.90 called Techline suggested gasket w11159728 30.00 ; ordrng 1 W11159728 (Gasket) and 1 WPW10280988 (Supply gasket) and 1 WPW10320706 (Return gasket)
We serviced a
WHIRLPOOL OVEN
Model WOS51EC7HS20
Near Seneca, SC 29672
Frank
Job Details:
06/06/2023
Inner door glass broke when on self clean mode . ; ordrng 2 WPW10284902 (Inner door glass)s and 1 Jobcodej13 (Job cod j13) and 1 W11598188 (Retainer divider)
We serviced a
JENN-AIR RANGE
Model JDRP548WP03
Near Salem, SC 29676
Frank
Job Details:
06/06/2023
Found on 18 inch door inner glass broken #3 on door parts shows discontinued.. W10115693.. called Techline. Can't give estimate due to can't get glass price 150.00 trip 149.99 Labor collecting trip charge for now; ordrng 1 W10115693 (Inner door) and 1 Jobcodel14 (Job code l14)
We serviced a
WHIRLPOOL OVEN
Model WFE535S0LZ2
Near Maggie Valley, NC 28751
Kari
Job Details:
06/06/2023
"Took quick pics, found the convection fan making noise as it spins, customer states it normally sounds like a screw is rattling around. When I took the fan cover off and ran it there was no noise, but did find the blade wobbles back and fourth as it spins, found the nut that holds the blade was stripped and couldnt be tightened down need parts for repair ; ordrng 1 W11582241 (Fan convection with blade) and 1 L14 (Job code) and 1 Okforanytech (Ok for any tech)"
We serviced a
JENN AIR RANGE
Model JES1750FS2
Near Sylva, NC 28779
Kari
Job Details:
06/06/2023
"Installed parts, ran cooktop on all 4 elements for 15-20 minutes on high and everything continued to boil and never shut off unit checks ok"