Service History 16 - Authorized Service Inc

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Easley, SC 29642

Larry M.

Job Details: 05/14/2025

Replaced control board. Unit would not respond. Verified correct power. Found new part defective. Will order control board. ; ordrng 1 W11603810 (Control board)

We serviced a

MAYTAG WASHER

Model MHW5630HW3

Near Columbus, NC 28722

Brian

Job Details: 05/14/2025

Found f9e1 (long drain) And F0e2 (oversuds) error codes. Customer said the unit wouldnt drain and they removed a hose and found coins clogging the line. I tested unit and found it complicating cycle without issues. Inspected drain filter and found some debris in it. Removed debris. Tested unit again and found all operations ok with no leaks detected.

We serviced a

WHIRLPOOL RANGE

Model WFG320M0MS0

Near Powdersville, SC 29673

Frank

Job Details: 05/14/2025

Replaced door seal unit working as designed

We serviced a

WHIRLPOOL WASHER

Model WTW4955HW3

Near Moore, SC 29369

Sam

Job Details: 05/14/2025

Found unit draining constantly. Has f3e1 error code. Unit needs new control. Will order.; ordrng 1 W11608056 (Control) and 1 L14 (L14)

We serviced a

MAYTAG WASHER

Model MHW5630HC3

Near Marshall, NC 28753

Kari

Job Details: 05/14/2025

"7741179626 Took quick pics, found unit showing 9-1 and 8-3 codes. And unit isnt draining all the way. Cleared codes ran drain pump found unit just hums. Unit would need drain assembly for repair. I called trade care when I left due to the house being an unsafe working environment, we will not being going back for repair due to the floor covered in excrement and roach debris. 7741179626"

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ4

Near Mars Hill, NC 28754

Kari

Job Details: 05/14/2025

Installed parts unit checks ok

We serviced a

MAYTAG WASHER

Model MVW4505MW1

Near Mars Hill, NC 28754

Kari

Job Details: 05/14/2025

"Took quick pics, found unit doing same as last time and harness is broken again. Installed new harness and added extra support clips from old harness to keep new one out of the way and raised feet so bottom of tub cant damage the harness either. Ran diagnostic cycle, unit checks ok; used 1 W11643701 (Harness) from stock"

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Greenville, SC 29607

Nathan

Job Details: 05/14/2025

"Control board glitching out and turning off. Wont go into calibration in diagnostics. Ordering ACU,actuator, capacitor,and wiring harness. ; ordrng 1 W11603810 (ACU) and 1 W11428524 (Capacitor) and 1 W11481722 (Shift actuator) and 1 W11652038 (Lower harness) and 1 N15laborcode (N15 labor code)"

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Weaverville, NC 28787

Kari

Job Details: 05/14/2025

"Took quick pics, found unit showing 8-1 long fill and unit is on a well system. Found the cold valve full of sediment. Installed new valve. Ran diagnostic cycle. Unit checks ok"

We serviced a

MAYTAG WASHER

Model MVWB865GW0

Near Pelzer, SC 29669

Jerry D.

Job Details: 05/14/2025

"Lots of problems, suspension worn out, lid broken in 3 places, 3 codes, touchpad inoperable code and flood conditions code , clutch code, j13, ordering , ; ordrng 1 W11130356 (Damper) and 1 W10734521 (Slider) and 1 W11135393 (Fascia) and 1 W11401710 (Cntrl) and 1 W11259006 (Lid)"

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF536RBS00

Near Belton, SC 29627

Jerry D.

Job Details: 05/14/2025

"Found frost and moisture in frez door not sealing, found mullion that top of rez door seals against is bowed bad, t line. Jeremy, Not repairable, 7741570283"

We serviced a

JENN-AIR RANGE

Model JES1750ML0

Near Belton, SC 29627

Jerry D.

Job Details: 05/14/2025

"Found display dead, volts and polarity good, ordering, j13; ordrng 1 W11603771 (Cntrl) and 1 W10759326 (Display)"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS555SIHZ06

Near Fountain Inn, SC 29644

Matt

Job Details: 05/14/2025

"Carl replaced parts,tested operation and all functions pass."

We serviced a

MAYTAG WASHER

Model MHW5630HC3

Near Weaverville, NC 28787

Kari

Job Details: 05/14/2025

"Took quick pics, found unit showing 9-1 long drain and full of water, cleared all water manually and removed panels, cleared debris from drain filter and vaccumed out the pump and hoses. Put everything back together and noticed large cuts in boot on left side. Need boot for complete repair ; ordrng 1 W11314648 (Gasket) and 1 L14 (Job code)"

We serviced a

WHIRLPOOL REFRIGERATOR

Model n/a

Near Weaverville, NC 28787

Kari

Job Details: 05/14/2025

Found when I got there unit is a Ken more.

We serviced a

WHIRLPOOL WASHER

Model WTW8500DC

Near Travelers Rest, SC 29690

Larry M.

Job Details: 05/14/2025

Found side of lid broken. Will order replacement. ; ordrng 1 WP8563965 (Left hinge) and 1 W11102314 (Lid) and 1 J13jobcode (J13 job code)

We serviced a

JENN-AIR MICROWAVE

Model JMW2430DS02

Near Travelers Rest, SC 29690

Larry M.

Job Details: 05/14/2025

Stuck key error code. $1151. Customer approved. $550.50 collected. ; ordrng 1 W10887855 (UI) and 1 N14jobcode (N14 job code) and 1 Walldolly (Wall dolly)

We serviced a

KITCHENAID DISHWASHER

Model KDTE204KPS2

Near Greenville, SC 29617

Larry M.

Job Details: 05/14/2025

Found seal leaking. Will order door seal. ; ordrng 1 W11414078 (Seal) and 1 W11664713 (Door seal)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SDHZ08

Near Anderson, SC 29626

Jerry D.

Job Details: 05/14/2025

"Temps 36@1, water okImk broken, installed imk from truck stock, imk harvest and fill ok; used 1 W11359448 (Imk) from stock"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ13

Near Anderson, SC 29626

Jerry D.

Job Details: 05/14/2025

"Doors unllevel unit and floor ok, adjusted right fresh door chks ok , also customer requested i remove handles and remove plastic from behind them, completed request, unit chks ok"

We serviced a

KITCHEN AID REFRIGERATOR

Model KRFC704FPS00

Near Taylors, SC 29687

Chris

Job Details: 05/14/2025

"Installed imk. Unit fills in test 97, rotates in step 120. Freezer temps are at 2 degrees and ice box fan is running. Unit check is ok"

We serviced a

MAYTAG WASHER

Model MVWX655DW1

Near Tryon, NC 28782

Brian

Job Details: 05/14/2025

"Customer said another company has been out multiple times and replaced multiple parts. (Quick pics).Found unit unplugged when I arrived. Plugged unit in and found drain pump coming on. Let pump time out. Entered diagnostic and found no saved error codes. Tested unit in diagnostic and found agitator plate rubbing. Inspected and found multiple coins stuck around agitator plate. Also found water, from drain hose, backing up in stand pipe. Moved drain hose to utility sink and removed coins from agitator plate. Calibrated and tested unit in auto diagnostic and manual diagnostic and found unit completing without issues. Also tested unit in rinse and spin. Unit completed without issues. At this time, all operations ok with no leaks detected. I recommended customer have plumbing issue resolved and informed customer that the drain hose in the sink will work, but there is no way for me to secure it in place. Customer understands. Reminded customer of proper loading procedures and proper cycle selection."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF535SWHZ12

Near Saluda, NC 28773

Brian

Job Details: 05/14/2025

"Dund interior lights in when I arrived but display is blank. When user interface buttons are pushed, all lights on ui and display illuminate until button is released. Cycled power to unit and attempted to put unit into test mode, but it would not respond. Contacted tech support and spoke to Chris. We checked continuity of wire harness and found it ok. New Main control (WPW10317076) needed. ; ordrng 1 WPW10317076 (Main control) and 1 L14 (Job code)"

We serviced a

WHIRLPOOL OVEN

Model WSGS7530RZ0

Near Etowah, NC 28729

Brian

Job Details: 05/14/2025

"Customer said unit will sometimes stop heating during cooking, when using both higher or lower temperatures. Found no saved error codes. Tested temp sensor and all burners and elements. All ok. Cooing fan is functioning . Control (W11758686) user interface (W11747652) and spark module (W10898291) needed. ; ordrng 1 W11758686 (Control) and 1 W11747652 (User interface) and 1 W10898291 (Sark module) and 1 U18 (Job code)"

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS0

Near Weaverville, NC 28787

Kari

Job Details: 05/14/2025

"Took quick pics, found solenoid dispenser only staying on the rinse aid side and not moving need dispenser for repair ; ordrng 1 W11412300 (Dispenser) and 1 J13 (Job code)"

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ4

Near Easley, SC 29640

Frank

Job Details: 05/14/2025

Replaced sump. Tested unit working as designed

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF757SDHZ03

Near Simpsonville, SC 29680

Carl

Job Details: 05/14/2025

"Installed new imk ,valve ,heater ran diagnostics and imk cycle"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDHZ03

Near Easley, SC 29642

Frank

Job Details: 05/14/2025

"Found leaking from hose in valve..Needed to re seat hose into valve.. ran water filled cup ok,filled imk ok no more leaking"

We serviced a

WHIRLPOOL MW OVEN COMBO

Model WOEC3030LS00

Near Salem, SC 29676

Frank

Job Details: 05/14/2025

Bb quoted $595.73. Not heating microwave.. no errors on unit.. turntable stop after 10 seconds.. ordering inverter and magnetron as per caution. Paying 297.86 owe 297.86. Gate code 1961; ordrng 1 W11325787 (Microwave control) and 1 W11578959 (Magnetron) and 1 W11578579 (Inverter) and 1 Jobcodel14 (Job code l14)

We serviced a

KITCHEN AID ICE MACHINE

Model KUID308HPS01

Near Salem, SC 29676

Frank

Job Details: 05/14/2025

Cleaning light is staying on after Cleaning cycle.. tried diag mode tried holding button.. couldn't clear it..; ordrng 1 W11034363 (Control) and 1 WPW10511923 (Bin thermistor) and 1 Jobcodel14 (Job code l14)

We serviced a

WHIRLPOOL WASHER

Model WTW4957PW0

Near Salem, SC 29676

Frank

Job Details: 05/14/2025

Unit stuck in drain mode.. ; ordrng 1 W11608056 (Control) and 1 Jobcodef12 (Job code f12)

We serviced a

MAYTAG WASHER

Model MHW8630HC3

Near Seneca, SC 29672

Frank

Job Details: 05/14/2025

Replaced console and detergent assembly.. all components lining up.. when screwing down console and putting top on detergent handle is out of alignment

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRQA59CNKZ

Near Asheville, NC 28804

Kari

Job Details: 05/14/2025

"Took quick pics, customer is concerned the crisper bins are too cold. FF is 39, rh crisper is 35 and lh crisper is 32, both fz sections are in the 0 range. Ran through diagnostics, unit had no codes stored. Put into manual test mode and ran through diagnostics the thermistor read out is correct and all dampers and fans are operating properly. Took crisper bins out to check operation of dampers to crispers and found there to be foam blacks on back of crisper shelf that were never removed from shipping, right above the damper vents, removed styrofoam. I believe air was trapped and wasnt circulating from the bottom correctly. Also found RH FF gasket ripped need part for repair. ; ordrng 1 W11456682 (Gasket) and 1 J13 (Job code)"

We serviced a

WHIRLPOOL FREEZER

Model WZF34X20DW06

Near Greenville, SC 29611

Nathan

Job Details: 05/14/2025

Kickplate was delivered bowed out letting more dirt get inside bottom of freezer. Also raised leveling legs so freezer is leaning and put food grade silicone behind gasket where it was pulling away from gasket channel. Office will call and schedule return visit when kick-plate and part for dishwasher comes in. ; ordrng 1 WPW10534161 (Kick-plate) and 1 C1laborcode (C1 labor code)

We serviced a

WHIRLPOOL DRYER

Model WED8127LC2

Near Simpsonville, SC 29681

Carl

Job Details: 05/14/2025

Installed new blower wheel cycled unit to ck operation unit ck ok

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRV986FDEM

Near Simpsonville, SC 29681

Carl

Job Details: 05/14/2025

Installed new fan kit unit ck ok

We serviced a

WHIRLPOOL MW OVEN COMBO

Model RMC305PVB00

Near Hendersonville, NC 28792

Brian

Job Details: 05/14/2025

Tested unit and found it not heating. Attempted to enter diagnostics and found unit not entering. Magnetron (W10245183) transformer (WP4375286) capacitor (W10850446) and diode (WPW10687786) Control (W10105800) and user interface (W10172473) needed. Found Control (W10105800) and user interface (W10172473) are no longer available. Repairs cannot be completed. ; ordrng 1 W10245183 (Magnetron) and 1 WP4375286 (Transformer) and 1 W10850446 (Capacitor) and 1 WPW10687786 (Diode) and 1 W10105800 (Control NLA) and 1 W10172473 (User interface NLA) and 1 Checknotes (Check notes)

We serviced a

MAYTAG WASHER

Model MVWC565FW3

Near Taylors, SC 29687

Chris

Job Details: 05/14/2025

Found loud silinoids on water valve. Replaced valve from stock. Unit check is ok ; used 1 W11210463 (Valve) from stock

We serviced a

WHIRLPOOL DRYER

Model WED4800XQ1

Near Union, SC 29379

Sam

Job Details: 05/14/2025

"Found unit not drying. checked incoming voltage. Incoming voltage good 240. Heating good. Checked airflow at back of machine. Unit lacking airflow. Found inside of blower housing clog of debris, lint and moisture causing blower wheel to not spin properly and seize up. Removed debris and all moisture lint in blower wheel and vent. Cycled unit. Unit now blowing air out of rear vent. Reinstalled house vent. Unit still has good airflow. Unit heats and tumbles. All functions pass."

We serviced a

WHIRLPOOL DRYER

Model LEQ9508PW1

Near Greenville, SC 29617

Larry M.

Job Details: 05/14/2025

Found relay suck closed. Will order switch and timer. ; ordrng 1 WP3406725 (Timer) and 1 WP3398094 (Start relay) and 1 J13jobcode (J13 job code)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS555SIHZ00

Near Union, SC 29379

Sam

Job Details: 05/14/2025

Installed door. Cycled icemaker harvest and fill. Both working. Dispensers working. All functions pass.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHB11

Near Boiling Springs, SC 29316

Sam

Job Details: 05/14/2025

Found units ice not dispensing. Motor humming and can hear activation of motor. Checked bucket and motor shaft. Found coupler stripped and ice bucket cracked where coupler goes. Will need new ice bucket and coupler. Will order.; ordrng 1 WPW10169511 (Coupling) and 1 WPW10558423 (Ice container) and 1 L14 (L14)

We serviced a

WHIRLPOOL DISHWASHER

Model WDF341PAPW2

Near Greenville, SC 29609

Nathan

Job Details: 05/14/2025

"Has F4E3 error, bad wash motor. Ordering sump assembly that comes with motor. Office will call and schedule return visit when parts arrive arrives. ; ordrng 1 N15laborcode (N15 labor code) and 1 W11613479 (Sump and motor assembly)"

We serviced a

WHIRLPOOL WASHER

Model WTW4957PW0

Near Greenville, SC 29609

Nathan

Job Details: 05/14/2025

Washer had very low drain outlet. Old drain pipe was broken off. Let homeowner know to get drain pipe repaired so its up enough to not siphon out water while washing essentials causing a low flow or no fill error. He said hell call back if theres anymore issues after replacing standpipe. Calibrated washer after leveling then ran a heavy cycle so water is as full as possible to make sure its not siphoning the way I hooked it up. Stopped washer while it was draining by unplugging it and all the water siphoned out. Washer wont work correctly until drain pipe is fixed.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SDHZ18

Near Six Mile, SC 29682

Frank

Job Details: 05/14/2025

"14 degrees in fc. 42 in rc. Evaporator looks ok, lightly frosting on top heavier towards the bottom of evap. Ordering board and thermistor to replace. ; ordrng 1 W11546690 (Control) and 1 WPW10384183 (Thermistor) and 1 Jobcodej13 (Job code j13) and 1 W11700250 (Imk)"

We serviced a

MAYTAG WASHER

Model MHW5630HC3

Near Taylors, SC 29687

Chris

Job Details: 05/14/2025

Found loose connection on control pin 14. Re seated connector. Unit check is ok . New labor authorization is m1e3rw1nl2

We serviced a

WHIRLPOOL DISHWASHER

Model WDT970SAKZ3

Near Greer, SC 29651

Chris

Job Details: 05/14/2025

Found water valve connection unplugged from valve. Reseated connection. Unit check is ok

We serviced a

WHIRLPOOL ICE MACHINE

Model WUI75X15HB01

Near Greer, SC 29651

Chris

Job Details: 05/14/2025

Found open bin thermistor. Replaced part . Unit check is ok

We serviced a

MAYTAG REFRIGERATOR

Model MRT118FFFM01

Near Mauldin, SC 29662

Matt

Job Details: 05/14/2025

Found valve leaking from valve body. Have customer estimate of 287.00 total to replace valve.Customer approved.Replaced water valve. Tested operation. All functions pass. Left the old part with the customer. Office to run card and e mail receipt. I did not move unit to repair it.; used 1 2315576 (Valve) from stock

We serviced a

FRIGIDAIRE REFRIGERATOR

Model PLHS67EGSB4

Near Greenville, SC 29607

Matt

Job Details: 05/14/2025

Found 120 bolts to ice maker. Ice maker does not rotate. Ice maker will need to be replaced. Blue book estimate for the total repair is $415.00. Customer is going to pay half today 207.50 and the other 207.50 when part is installed.; ordrng 1 241798231 (Ice maker) and 1 Anytech (Any tech) and 1 C1jobcode (C1 job code)

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ4

Near Greenville, SC 29605

Matt

Job Details: 05/14/2025

Customer said no water entering in machine and it runs loud. Water/condensation inside the machine when the cycle is complete. 7.6 amps in wash and 4.0 in dry.Called tech line and spoke to Jared.Up the jet dry dispenser setting. Set a realistic expectation of drying of a plastic dishwasher. Plastic is not dense enough to hold heat like a stainless or porcelain dishwasher and that allows for more water to be left after the cycle is complete.Dishwasher is working as designed. File number 7741572162.

We serviced a

KITCHENAID RANGE

Model KSGG700ESS7

Near Waynesville, NC 28785

Kari

Job Details: 05/13/2025

"Took quick pics, found unit not heating properly checked temp and found it never gets above 323 but beeps that its at 350. Need control and sensor for repair ; ordrng 1 W10833885 (Sensor) and 1 W11685628 (Control main) and 1 Q16 (Job code)"

We serviced a

KITCHENAID REFRIGERATOR

Model KRSF705HPS05

Near Fountain Inn, SC 29644

Jerry D.

Job Details: 05/13/2025

"Temps 36@1, water ok, Imk broken, ordering, j13; ordrng 1 W11130444 (Imk)"

We serviced a

KITCHENAID REFRIGERATOR

Model KRFF577KPS02

Near Gaffney, SC 29341

Sam

Job Details: 05/13/2025

Pulled unit out and adjusted drier filter position per whirlpool. Reinstalled unit to wall. Checked all components in diagnostics. Cycled every component. Noise could not be duplicated. Called techline. Techline stated that based on adjustment of filter to see if that took care of issue seeing as units noise cannot be duplicated at time of visit.

We serviced a

WHIRLPOOL RANGE

Model WFE525S0JS4

Near Gaffney, SC 29341

Sam

Job Details: 05/13/2025

Installed light assembly and bulb to unit. Cycled units light by opening and closing door. Units light comes on and goes off as directed to. All functions pass.

We serviced a

WHIRLPOOL ICE MACHINE

Model GI15NDXZB0

Near Greenville, SC 29601

Larry M.

Job Details: 05/13/2025

Found water valve not working properly. Will order ice maker and control board. ; ordrng 1 W11034363 (Control) and 1 W10881366 (Valve) and 1 N14jobcode (N14 job code)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF555SDFZ15

Near Greenville, SC 29609

Nathan

Job Details: 05/13/2025

Unit was unplugged when I arrived. Plugged in unit and compressor is locked up pulling locked rotor amps. Ordering sealed system components and office will schedule return visit when parts arrive. ; ordrng 1 W11547313 (Compressor) and 1 W11550396 (Evaporator) and 1 Processstub (Process stub) and 1 W11109499 (Drier (only if still in small van)) and 1 W11504447 (Drier to capillary tube union) and 1 W11504423 (Evap coupler) and 1 W11504415 (Suction tube to compressor) and 1 X20laborcode (X20 labor code (have to remove doors to get behind refrigerator))

We serviced a

WHIRLPOOL DOUBLE WALL OVEN

Model WOD51EC0HS20

Near Greenville, SC 29605

Nathan

Job Details: 05/13/2025

F6E4 communication mismatch. Already replaced all control boards and another company replaced the appliance manager again. Says it was working better but still not working right. Boyd file number 7741558460 says to call trade care and let them know the unit wasnt working since new and that homeowner will have to go through them to either swap out or give repair concessions. Whirlpool isnt covering anymore part replacements due to oven being a scratch and dent model. Waited on hold for trade care to see how they want to proceed. 1866-233-8547 (trade care number file number 7741558460) Whirlpool trade care says that homeowner has to call trade care to see if the unit is covered under warranty.

We serviced a

MAYTAG WASHER

Model MVW7232HC2

Near Easley, SC 29640

Matt

Job Details: 05/13/2025

Put unit in diagnostics and found F0e5 error ( out of balance). Customer started unit started washing with no water. Recalibrated control and ran a quick wash cycle with a load. All functions pass.

We serviced a

WHIRLPOOL WASHER

Model WTW5010LW0

Near Easley, SC 29642

Matt

Job Details: 05/13/2025

"Found unit has lid lock that would not unlock. Replaced lid lock, checked operation, checks o.k"

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS3

Near Greenville, SC 29609

Larry M.

Job Details: 05/13/2025

Found control board shorting out. Will order. ; ordrng 1 W11629911 (Control board) and 1 J13jobcode (J13 job code)

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS3

Near Travelers Rest, SC 29690

Larry M.

Job Details: 05/13/2025

Found unit not draining. Unplugged sink drain. Ran test cycle. All functions pass

We serviced a

MAYTAG DRYER

Model MEDC300XW0

Near Travelers Rest, SC 29690

Larry M.

Job Details: 05/13/2025

Replaced timer and start relay. Ran test cycle. All functions pass.

We serviced a

KITCHEN AID MW OVEN COMBO

Model KOCE500ESS22

Near Simpsonville, SC 29681

Carl

Job Details: 05/13/2025

Installed new acu and mag tube cycled unit to ck operation unit ck ok

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS571CIHW01

Near Easley, SC 29640

Frank

Job Details: 05/13/2025

Replaced evap fan. Tested working as designed

We serviced a

WHIRLPOOL RANGE

Model WFE525S0JS1

Near Fountain Inn, SC 29644

Jerry D.

Job Details: 05/13/2025

Installed listed parts cycled unit through test and unit checks ok

We serviced a

KITCHENAID COOKTOP

Model KFEG500ESS7

Near Simpsonville, SC 29681

Jerry D.

Job Details: 05/13/2025

Installed listed parts cycled unit through test unit checks okay

We serviced a

MAYTAG WASHER

Model MVW6500MBK0

Near Simpsonville, SC 29681

Jerry D.

Job Details: 05/13/2025

Installed listed parts cycled unit through test and all functions are working properly

We serviced a

KITCHEN AID RANGE

Model KSGG700ESS1

Near Simpsonville, SC 29681

Jerry D.

Job Details: 05/13/2025

"Ordering interface, j13; ordrng 1 W10901124 (Console)"

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Pickens, SC 29671

Frank

Job Details: 05/13/2025

Found unit stuck in drain mode.. needs new board ; ordrng 1 W11603810 (Control) and 1 Jobcodef12 (Job code f12)

We serviced a

JENN-AIR REFRIGERATOR

Model JF42NXFXDE05

Near Salem, SC 29676

Frank

Job Details: 05/13/2025

43 degrees in fc. 0 IN Freezer .. found icing up coming into fridge evap. Could be leak of restriction.; ordrng 1 Jobcodex20 (Job code x20) and 1 Sealedsystemtech (Sealed system tech) and 1 W11649687 (Evaporator) and 1 W11557671 (Compressor) and 1 Drier (Drier) and 1 Accessport (Access port) and 1 R600a (R600a)

We serviced a

WHIRLPOOL DISHWASHER

Model WDF331PAMS0

Near Simpsonville, SC 29680

Jerry D.

Job Details: 05/13/2025

"F2 code, Needs console, Estimate, 562.00 , customer thinking, charge cc 150.00"

We serviced a

AMANA WASHER

Model NTW4516FW4

Near Mauldin, SC 29662

Nathan

Job Details: 05/13/2025

Called homeowner to come out to look at washer. Explained that when cycle is done control board turns on pump and wont allow washer to start another cycle. ACU isnt in stock but well sneak into schedule once we receive it in stock. Office will call and schedule return visit. ; ordrng 1 W11603811 (ACU) and 1 F12laborcode (F12 labor code) and 1 GiveparttoNathantosneakin (Give part to Nathan to sneak in)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDEM01

Near Greenville, SC 29615

Nathan

Job Details: 05/13/2025

When arriving I noticed three way valve clicking. Unplugged dc components to see if anythings loading down unit. LED lights are all out and theres no compressor or fans on. After unplugging and plugging back in refrigerator it came back to life. Let homeowner know that in this situation when theres no lights or fans working we order the control board just to start and if it ends up being other parts then itll cost more than the refrigerator. Control boards usually around $700 for this style refrigerator. Let homeowner know if the same exact symptoms occur it would be better to get a new refrigerator. This refrigerator is out of regular and compressor warranty and a compressor issue would exceed the cost of a new refrigerator. Everythings performing as designed now. Should take about 12 hours to get back down to correct temperature. Office will send receipt for trip fee after card is charged $150.00 thank you.

We serviced a

JENN-AIR OVEN

Model JJW2430DP02

Near Salem, SC 29676

Frank

Job Details: 05/13/2025

F2e1 code needs console W11236887. Bb quoted1497.24 paying tc 150$

We serviced a

MAYTAG DRYER

Model MED4500MW0

Near Gaffney, SC 29340

Sam

Job Details: 05/13/2025

Found unit will not turn off after desired period of time when set on timed dry. Timer not rotating and ending cycle unit just continues to cycle. Unit heats and tumbles like normal. Unit will need new timer. Will order timer for repair.; ordrng 1 W11685947 (Timer) and 1 L14 (L14)

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Asheville, NC 28803

Brian

Job Details: 05/13/2025

"Installed new control. Calibrated and tested unit. At this time, all operations ok with no leaks detected."

We serviced a

WHIRLPOOL WASHER

Model WTW4957PW0

Near Candler, NC 28715

Brian

Job Details: 05/13/2025

"Installed new inlet valve. Calibrated and tested unit observing for leaks and proper functions. At this time, all operations ok with no leaks detected."

We serviced a

WHIRLPOOL DISHWASHER

Model mdb4949skz3

Near Easley, SC 29640

Matt

Job Details: 05/13/2025

Found dishwasher leaking from multiple locations. Found dishwasher leaking from left rear seam and inner door. Will order.; ordrng 1 W11559689 (Inner door) and 1 X20jobcode (X20 job code) and 1 W11409865 (Tub)

We serviced a

KITCHENAID DISHWASHER

Model KDTE204KPS3

Near Gaffney, SC 29340

Sam

Job Details: 05/13/2025

"Installed dispenser and control. Cycled unit through diagnostic cycle. Units dispenser door now opening. Unit washing, heating and draining. All functions pass."

We serviced a

WHIRLPOOL DRYER

Model WED4850HW0

Near Spartanburg, SC 29307

Sam

Job Details: 05/13/2025

Found unit not stopping cycle. Unit heats and tumbles but does not progress timer. Unit will need new timer for repair. Will order.; ordrng 1 WPW10436303 (Timer) and 1 L14 (L14)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHZ06

Near Candler, NC 28715

Kari

Job Details: 05/13/2025

Installed parts unit checks ok

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Candler, NC 28715

Kari

Job Details: 05/13/2025

Installed parts unit checks ok

We serviced a

WHIRLPOOL WASHER

Model WTW8500DC0

Near Chesnee, SC 29323

Sam

Job Details: 05/13/2025

"Installed new lid and hinge. Cycled unit through quick test cycle. All components working. Units lid secure, Opens and closes properly. All functions pass."

We serviced a

WHIRLPOOL DISHWASHER

Model WDF341PAPW2

Near Walhalla, SC 29691

Frank

Job Details: 05/13/2025

"Found unit not filling with water? Filled manual, motor working ok. Found supply valve not letting in water.; O-emld tckt"

We serviced a

KITCHENAID OVEN

Model KFGD500ESS12

Near Greenville, SC 29615

Chris

Job Details: 05/13/2025

Installed new parts. Unit check is ok

We serviced a

KITCHENAID MW OVEN COMBO

Model KOEC530PSS00

Near Greer, SC 29651

Chris

Job Details: 05/13/2025

Found invertor unplugged. Re seated connection. Unit check is ok . New labor authorization is k1e3980nl2

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ03

Near Greer, SC 29650

Chris

Job Details: 05/13/2025

Installed light. Unit check is ok

We serviced a

KITCHEN AID REFRIGERATOR

Model KRMF706ESS04

Near Greer, SC 29651

Chris

Job Details: 05/13/2025

Installed new parts. Unit check is ok

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SDHM12

Near Greer, SC 29651

Chris

Job Details: 05/13/2025

"Unit has kinked waterline, inside door hinge keeping door from fully closing calls and moisture buildup inside cabinet. Uninstall door and rerouted waterline reinstall door unit check is OK . New auth is w1e3ja1nl1.5"

We serviced a

KITCHEN AID RANGE

Model KSEG950ESS2

Near Spartanburg, SC 29306

Sam

Job Details: 05/13/2025

Found unit not wanting to turn bake on. Necked broil and bake separately units broil works but bake does not. Will order bake element.; ordrng 1 W10779716 (Bake element) and 1 L14 (L14)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDBM00

Near Seneca, SC 29678

Frank

Job Details: 05/13/2025

Cycled imk.. not making water valve kick on. Need to order imk bb quoted $484.44. Replaced bulb in microwave. Not repairing imk at this time.; used 1 8206232a (Bulb) from stock

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Liberty, SC 29657

Frank

Job Details: 05/13/2025

Unit stuck in drain mode.. need control; ordrng 1 W11603810 (Control) and 1 Jobcodef12 (Job code f12)

We serviced a

KITCHENAID ICE MACHINE

Model KUID508HPS01

Near Seneca, SC 29678

Frank

Job Details: 05/13/2025

Need email. Finding cool plate not getting cold. Condenser fan running. Compressor not running. Ordering Compressor for replacement...; ordrng 1 Jobcodex20 (Job code x20) and 1 Sealedsystem (Sealed system tech) and 1 R134a (R134a) and 1 W11735041 (Compressor) and 1 W10843121 (Drier) and 1 Accessport (Access port) and 1 WPW10218037 (Evaporator)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRMF3636RZ00

Near Pendleton, SC 29670

Frank

Job Details: 05/13/2025

Switch frozen. Defrosted Switch started light working...

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FRD13254H0

Near Simpsonville, SC 29681

Carl

Job Details: 05/13/2025

Found unit has a seal system issue with the back panel starting to rust out advised customer of issue and cost and age customer is not going to repair unit

We serviced a

WHIRLPOOL WASHER

Model AZ

Near Simpsonville, SC 29681

Carl

Job Details: 05/13/2025

Ran diagnostics found error code for long fill and a bad clutch l14; ordrng 1 W11173599 (Valve) and 1 L14 (Labor) and 1 W10754448 (Clutch)

We serviced a

WHIRLPOOL WASHER

Model WTW4957PW0

Near Easley, SC 29640

Matt

Job Details: 05/13/2025

Found out tub leaking near drain pump. Will order.; ordrng 1 W10371566 (Outer tub) and 1 X20jobcode (X20 job code)

We serviced a

AMANA WASHER

Model NTW4519JW2

Near Greenville, SC 29611

Larry M.

Job Details: 05/13/2025

Replaced control board. Ran test cycle. All functions pass.

We serviced a

WHIRLPOOL REFRIGERATOR

Model MSS25C4MGZ09

Near Easley, SC 29642

Larry M.

Job Details: 05/13/2025

Found heater open. Replaced heater previously. Will order heater. ; ordrng 1 W11650661 (Heater) and 1 N14jobcode (N14 job code)

Contact Us Today

About Us