We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Hendersonville, NC 28739
Derek
Job Details: 07/10/2023
Unit flashing clean light and wont start cycle. 8-4 float up and 9-2 drain error from excessive drain pump usage due to up float. Water in float tray. Cleared water and checked gasket. Gasket deformed in upper corner causing poor seal and leaking down the inside of door. Heated to reshape gasket and cycled unit. No leaks. Unit checks ok. Advised about survey.
We serviced a
WHIRLPOOL DISHWASHER
Model KDPM604KPS1
Near Burnsville, NC 28714
Kari
Job Details: 07/10/2023
Ordering parts ; ordrng 1 N15 (Job code) and 1 W11559689 (Inner door) and 1 W11664713 (Door seal)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ02
Near Greenville, SC 29615
Cliff
Job Details: 07/10/2023
"Replaced parts, programmed control, all functions check ok"
We serviced a
WHIRLPOOL VENTHOOD
Model kxd4636yss7
Near Greenville, SC 29607
Cliff
Job Details: 07/10/2023
"Replaced part, cycled unit, all functions check ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDW09
Near Belton, SC 29627
Jerry D.
Job Details: 07/10/2023
"Installed imk sent preid, cycled unit through test and no leaks found , harvest and fill ok, no leaks found"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Weaverville, NC 28787
Matt
Job Details: 07/10/2023
"Customer stated unit randomly throws ice in the floor. No one in the room with the refrigerator. Ice sickles and leaking from freezer. Found air leak at top right of freezer seal.Called tech line and spoke to Nate. Found air leak at top right of freezer causing ice sickles. Corrected seal, checks o.kTech line wanted to make sure outlet is on dedicated circuit and is properly polarized and grounded.Outlet is polarized and grounded. Tech line sending the info to engineering.SR number 7736820968"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT348FMES04
Near Candler, NC 28715
Matt
Job Details: 07/10/2023
Found unit was warm and all the food has Thawed out. Customer has found it to be freezing then thawing. Found evaporator has one pass of frost. Will order compressor and evaporator.; ordrng 1 W11578004 (Evaporator) and 1 W11635510 (Compressor) and 1 MaorDe (Ma or De) and 1 Sealedsystem (Sealed system) and 1 X20jobcode (X20 job code) and 1 W11506635 (Port) and 1 R600a (R600a) and 1 Customerwantstopreschedule (Customer wants to pre schedule)
We serviced a
MAYTAG WASHER
Model MHW5630HW2
Near Anderson, SC 29625
Jerry D.
Job Details: 07/10/2023
"Installed listed parts , plugged unit in, cycled unit through test and all functions are working properly"
We serviced a
MAYTAG WASHER
Model MVWC565FW3
Near Anderson, SC 29625
Jerry D.
Job Details: 07/10/2023
"Cntrl inop, drain pump broken, volts and polarity good, harness broken, ordering, j13; ordrng 1 W11577997 (Cntrl) and 1 W11259498 (Pump drain) and 1 W11255099 (Harness)"
We serviced a
JENN-AIR MICROWAVE
Model JMC2430IL03
Near Fountain Inn, SC 29644
Carl
Job Details: 07/10/2023
Installed new acu applied power after but up got an f6e6 error went to service matters and was off line called teck line and they are in training will call later; O-emld tckt
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Simpsonville, SC 29681
Carl
Job Details: 07/10/2023
Ck voltage at the ui relay and incoming ck good installed new control cycled unit several times and let it run a bit unit ck ok
We serviced a
KITCHENAID REFRIGERATOR
Model KUDF204KSB00
Near Seneca, SC 29672
Frank
Job Details: 07/10/2023
0 degrees in freezer..no water in ice maker.; ordrng 1 W11596827 (Ice maker) and 1 Jobcodel14 (Job codebl14)
We serviced a
KITCHEN AID ICE MACHINE
Model KUID308ESS2
Near Greer, SC 29650
Chris
Job Details: 07/10/2023
Unit has bad smart valve .gave customer a bluebook estimate for repair at 591.49. Installed new part. Unit check is ok
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Greer, SC 29650
Chris
Job Details: 07/10/2023
Unit has shorted control . Gave customer a blue book estimate for repair with tax and shipping at $543.26.customer declined estimate
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS04
Near Greer, SC 29651
Chris
Job Details: 07/10/2023
"Installed new parts, unit check is ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ08
Near Greer, SC 29651
Chris
Job Details: 07/10/2023
Found leaking water valve. Replaced valve. Unit check is ok
We serviced a
KITCHENAID BUILT-IN M/W
Model KMBD104GSS01
Near Hendersonville, NC 28791
Brian
Job Details: 07/10/2023
"Installed new console and control and power supply and clock. Tested unit multiple times, and with customer present. At this time, all operations ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX988SIBM01
Near Hendersonville, NC 28791
Brian
Job Details: 07/10/2023
"Installed new water line and inlet valve. Tested water dispenser and ice maker, observing for leaks and proper functions. At this time, all operations ok with no leaks detected."
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFC302EPA00
Near Zirconia, NC 28790
Derek
Job Details: 07/10/2023
Installed gasket. Cycled unit. Unit checks ok.
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Hendersonville, NC 28739
Brian
Job Details: 07/10/2023
"Customer said they would get check lent screen error code, even though lent screen was clear. Found blower working properly. Found some lent build up at vent, outside. Recommended customer keep an eye on vent and keep clean a needed. Customer understood. Did not move unit."
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Hendersonville, NC 28739
Brian
Job Details: 07/10/2023
"Found F0e3 (overload) error. Customer said that sometimes, unit will add cold water or hot water when it isnt selected. And sometimes unit will have no water and unit is in the wash cycle. Customer showed me a video of that. Tested and found unit mechanics ok. Also found display pixilated in some spots. Control (W11624943) drawer (W11614513) and ui (W11478526) needed. ; ordrng 1 W11624943 (Control) and 1 W11614513 (Drawer) and 1 W11478526 (User interface) and 1 L14 (Job code)"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Fountain Inn, SC 29644
Flint
Job Details: 07/10/2023
"New tub is cracked as well, will reorder; ordrng 1 W10371566 (Outer tub)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFC604FSS01
Near Black Mountain, NC 28711
Matt
Job Details: 07/10/2023
Refrigerator temperature is 57 and freezer is Rc Evap thermistor shows 7degrees. Checked evaporator and found green corrosion on suction line where it enters the liner and liner insulation has crumbled some indicating unit has frosted up the suction line most likely from a leak. Pulled unit forward on scuff shield and found the compressor has a port and drier filter has been changed. Put gauges on and found unit in a -20 vacuum. Recovered what refrigerant was left. Pulled a vacuum and weighed in 4.5 ounces of 134a and leak checked.ordering system; ordrng 1 W11592010 (Compressor) and 1 W11099748 (Freezer evaporator) and 1 W11291123 (Fresh food evaporator) and 1 W11575001 (3way valve) and 1 X20jobcode (X20 job code) and 1 Customerwantsprescheduled (Customer wants pre scheduled) and 1 MaorDeonky (Ma or De only)
We serviced a
AMANA DRYER
Model NED4655EW1
Near Hendersonville, NC 28792
Brian
Job Details: 07/10/2023
Found drum visually damaged. Installed new drum and tested. Found all operations ok at this time.
We serviced a
WHIRLPOOL WASHER
Model WTW8200YW0
Near Greenville, SC 29609
Flint
Job Details: 07/10/2023
"Found latch broken, needs new latch mechanism, estimate is 433.00, customer paid 125.00. Remainder if needed is 308.00"
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Greenville, SC 29609
Flint
Job Details: 07/10/2023
"Unit was not heating, replaced parts listed and it heated on timed dry but not on sensor dry, tested several times, sometimes it would heat fine others no heat, will order a board; ordrng 1 W11618916 (Board)"
We serviced a
WHIRLPOOL WASHER
Model WFW9400SW01
Near Greenville, SC 29607
Flint
Job Details: 07/10/2023
"Replaced the door boot and ran the unit to ensure there where no leaks, unit tested good."
We serviced a
MAYTAG WASHER
Model MHW5630HW3
Near Leicester, NC 28748
Kari
Job Details: 07/10/2023
"Took quick pics and unit showing an f8e1 low flow code. Customer had the wheel worked on due to sediment issue and it looks like something could have happened to where theres too much sediment in the valve, causing it to drip constantly now. Found it theres always water in the dispenser due to the fact that the valve isnt closing properly the only way you can get it to turn off is to turn it off at the tap. Installed new valve ran unit through diagnostic cycle unit checks OK?; used 1 W11316256 (Valve) from stock"
We serviced a
WHIRLPOOL DRYER
Model WED8127LW2
Near Marshall, NC 28753
Kari
Job Details: 07/10/2023
"Took quick pics found unit time jumps around and it takes a long time to dry it randomly give airflow errors even though the ducts have been cleaned and the lines are clear. Checked unit for codes unit just had a stick button code cleared unit ran unit three diagnostic cycle. It cut off almost immediately. Ran unit on time dry cycle. It run for about 3 to 5 minutes. When I open the door found that it was warm but not as hot as it should be pulled unit out and checked incoming power at terminal block. Founded to check good across black and red leads unplugged unit, and thats when I noticed the cord was a bit melted on one of the hot leads also found the outlet showing signs of melting and disfigurement. Found that the power never stays consistent 240 when its just my meter plugged into the outlet. Advised customer not plug unit back in since this is a fire hazard and to get an electrician to fix the outlet and get a new cord before they use it again. Thermistors and heater. Ill check good on resistance chicks unit checks. OK will need power corrected"
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFC302ESS03
Near Weaverville, NC 28787
Kari
Job Details: 07/10/2023
"Took quick pics, found unit freezer 18 degrees and the back wall has frost on the outside. Took resistance and power checks on thermistors bi metal and heater. All check ok. Found the heater is hot and is pulling 4.25 amps when on. took control panel down in ff section and made sure everything is plugged in tight and no pins were bent. Everything looks good. Checked wiring throughout cabinet on thermistors and heater to board all have resistance. Call Techline and spoke with. I think his name was Eric. I had to call him from the car because Techline was closed. When I tried to call from the house I gave him an entire history of the work that has been done up until now. I also told him that it seems the only last about two months until shes having The exact same issue told him about the amp draw on the heater. I did tell him the heater is getting home. He asked me if it could be an incomplete defrost. I told him I couldnt know for sure based on how I checked the unit today he also took all the part numbers they have been previously installed and he said that hes escalating this to engineering. He took my work email and said their engineering should be getting back to me within the next couple of days. I called and left the customer a voicemail letting them know the update, and will contact them again when I hear back from engineering.; ordrng 1 Waitingonengineer (Waiting to hear from WP)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ05
Near Mars Hill, NC 28754
Kari
Job Details: 07/10/2023
"Took quick pics, found unit unplugged. Plugged unit in and let run, found fans come on and damper opens, but the compressor doesnt stay running, found the compressor will click on, run for less than 30 seconds and turn off. Found 120v constant to compressor and starter resistance checks ok. Sealed system is under manufacturer 5 year Parts & Labor warranty. Will need parts for repair had office run credit card for $150 trip charge emailed receipt; ordrng 1 U18 (Job code) and 1 NeedR134aequipment (R134a) and 1 SStech (SS tech) and 1 W10507884 (Compressor) and 1 WPW10143759 (Drier)"
We serviced a
MAYTAG WASHER
Model MHW5630HC1
Near Weaverville, NC 28787
Kari
Job Details: 07/10/2023
"Took quick pics, found unit showing F0E2 ran unit through test 12 all steps pass and no codes stored now. Customer had a load of towels in it, ran drain and spin, unit just flops the clothes around. Never actually spins, found the floor slopes to the left a bit but the machine was never leveled by installer. Leveled feet and locked nuts, ran same load again unit now spins at high speed. Also advised customer use less detergent. Unit checks ok"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706ESS01
Near Asheville, NC 28801
Matt
Job Details: 07/10/2023
Found both sections warmer than set point. Freezer was empty. Fresh food was at 41. Found unit running at 5 psig low side and 220 high side while cooling fresh food section. Low side would pull down in to a vacuum and the high side pressure would go up. A few minutes later you could hear refrigerant flow into the evaporator and high side pressure would drop and low side would rise. Put unit in test 4. Recovered refrigerant. Blew the system out and replaced three way valve and drier filter. Pulled a long vacuum and weighed in 6.0 ounces of 134a. If unit restricts again we will need to replace both evaporators.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADB7
Near Mills River, NC 28759
Brian
Job Details: 07/10/2023
Found kick plate off when I arrived and retainers missing. Unit not mounted. Also found lower spray arm visually broken. Spray arm (WPW10319027) 2 screws (WP308685) 2 retainer (WPW10503548) needed. ; ordrng 1 WPW10319027 (Spray arm) and 2 WP308685 (Screws)s and 1 W10876537 (Drain pump) and 2 WPW10503548 (Retainer)s and 1 J13 (Job code)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ07
Near Piedmont, SC 29673
Jerry D.
Job Details: 07/10/2023
"Found left door to low not shutting properly, installed bushing wp487576 from truck stock, cycled unit through test and all functions are working properly"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Spartanburg, SC 29302
Chris
Job Details: 07/10/2023
Helped tp
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Tryon, NC 28782
Derek
Job Details: 07/10/2023
Installed parts and cycled unit. Unit checks ok.
We serviced a
JENN-AIR COOKTOP
Model JGD3536GS00
Near Seneca, SC 29672
Frank
Job Details: 07/10/2023
Replaced spark module tested working ok
We serviced a
WHIRLPOOL ICE MACHINE
Model KUIX335HPS01
Near Seneca, SC 29672
Frank
Job Details: 07/10/2023
Cabinets and counter top heating up .. found icebin full. Ran through diagnostics condenser fan running ok. operating as intended at this time.
We serviced a
WHIRLPOOL DISHWASHER
Model MDB9959SKZ0
Near Seneca, SC 29672
Frank
Job Details: 07/10/2023
Unit pulled out on arrival.. pump broke between motor and sump leaking while running. ; ordrng 1 W11416363 (Sump and motor) and 1 L14jobcode (Job code l14)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Seneca, SC 29678
Frank
Job Details: 07/10/2023
57 degrees in refrigerator.. 0 degrees in fc. Seems control not opening diffuser to cool refrigerator down ; ordrng 1 W11645127 (Diffuser) and 1 W11558182 (Control board) and 1 Jobcodel14 (Job code l14)
We serviced a
WHIRLPOOL RANGE
Model WFE515S0JS3
Near Seneca, SC 29678
Frank
Job Details: 07/10/2023
Unit pulled out on arrival.. display blank not responding checked voltage all ok .. ; ordrng 1 W11583303 (Control board) and 1 Jobcodel14 (Job code l14)
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS
Near Seneca, SC 29678
Frank
Job Details: 07/10/2023
Replaced heater tested working ok
We serviced a
WHIRLPOOL DISHWASHER
Model KDTE334GPS0
Near Westminster, SC 29693
Frank
Job Details: 07/10/2023
Replaced door seal tested working ok. ; used 1 W11177741 (Door seal) from stock
We serviced a
KITCHEN AID REFRIGERATOR
Model KUIX305ESS1
Near Greenville, SC 29607
Flint
Job Details: 07/10/2023
"Replaced valve and let it go thru a cycle, the unit tested good."
We serviced a
WHIRLPOOL DRYER
Model WED5000DW2
Near Simpsonville, SC 29680
Carl
Job Details: 07/10/2023
Found heater and hi limit open and door gasket is worn installed new heater and hi limit will order door gasket j13; ordrng 1 W10906683 (Door gasket) and 1 Hightempadhesive (Glue)
We serviced a
WHIRLPOOL FREEZER
Model WZF34X20DW05
Near Cowpens, SC 29330
Tyler
Job Details: 07/10/2023
Found seal not making contact again. Ordering door.; ordrng 1 W10746789 (Door) and 1 L14jobcode (L14 job code)
We serviced a
WHIRLPOOL OVEN
Model WOD51EC0HS20
Near Boiling Springs, SC 29316
Tyler
Job Details: 07/10/2023
"Touch screen freezing up not allowing selections after oven war,s up and door is opened.; ordrng 1 W11600355 (Control panel) and 1 L14jobcode (L14 job code)"
We serviced a
WHIRLPOOL DRYER
Model WED9200SQ0
Near Greenville, SC 29605
Cliff
Job Details: 07/10/2023
"Found the center UI is missing the button from board itself, board is no longer available through manufacturer, customer found a used one online and will have us install when it comes in."
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ0
Near Greenville, SC 29611
Cliff
Job Details: 07/10/2023
"Customer was hearing the drain pump in the beginning of cycle and then the wash motor turning on and off in beginning as well, found no error codes, all functions check ok."
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Simpsonville, SC 29680
Carl
Job Details: 07/10/2023
Installed new latch and lock ran diagnostics and a test cycle to ck operation unit ck
We serviced a
KITCHEN AID DISHWASHER
Model KDTM404KPS0
Near Pickens, SC 29671
Flint
Job Details: 07/10/2023
"Pulled unit out, replaced drain pump, reinstalled and tested , the unit drained and tested good."
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Lyman, SC 29365
Tyler
Job Details: 07/10/2023
Customer states ui does not respond sometimes. No errors found and him tested good in diagnostics. All functions tested good.
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Moore, SC 29369
Tyler
Job Details: 07/10/2023
Found gearcase leaking oil. And squeaking.; ordrng 1 W11449840 (Gearcase) and 1 W10721967 (Splutch) and 1 WPW10006384 (Belt) and 1 J13jobcode (J13 job code)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDB02
Near Moore, SC 29369
Tyler
Job Details: 07/10/2023
Found drain clogged. Cleared drain. All functions tested good.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM8
Near Spartanburg, SC 29306
Tyler
Job Details: 07/10/2023
"F4e3, F7e1 errors. Wash motor is bad. Gave estimate for $601.41. Collected $150.00 via card."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Spartanburg, SC 29302
Tyler
Job Details: 07/10/2023
"Installed parts, tested for operation. All functions tested good. Double labor auth: w17pwb1nl2"
We serviced a
MAYTAG WASHER
Model MVW5430MW0
Near Barnardsville, NC 28709
Kari
Job Details: 07/10/2023
"Took quick,pic,s found unit wouldnt run a cycle. Put unit into diagnostics and found unit showing latch wont lock code. Found when you try to engage a cycle, the latch will just continuously click. Installed new latch. Ran diagnostic cycle. Unit checks ok. ; used 1 W11513248 (Latch) from stock"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ03
Near Mill Spring, NC 28756
Derek
Job Details: 07/10/2023
Installed parts. Pulled vacuum. Charged unit with recommended charge per data tag. Cycled unit. Unit cooling and checks ok.
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Leicester, NC 28748
Kari
Job Details: 07/07/2023
"Took quick pics, found unit shaking when spinning when it doesnt have clothes in it its been just fine. Found the pedestal wasnt locked, and the feet were uneven, even out the feet according to the level on the floor, Pedestal is showing level on all four sides. Theres a little bit of movement out of the machine put a load of towels in and ran a rinse and spin found that I would never really spin fully. just rolled the clothes around on a high-speed ran the same cycle but with a slow speeds in found unit did spin the towels out now, but it did shake quite a bit still, Where you can visibly see things shaking on top of the dryer if you lay on the floor while its spinning You can see the floor move but the washer feet stay on the floor told customer since unit is on a crawlspace they would need to have the floor supported in some way or the other option would be to take the unit off the pedestals. Unit is functioning as designed recommended customer get floor reinforced"
We serviced a
MAYTAG DRYER
Model MEDC300XW0
Near Greer, SC 29651
Chris
Job Details: 07/07/2023
"Unit has locked up rollers, gave customer a bluebook estimate for dryer repair kit with tax and shipping at $373.41. Installed new parts. Unit check is ok ; used 1 4392065 (Kit) from stock"
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Spartanburg, SC 29301
Tyler
Job Details: 07/07/2023
F8e1 error code. Found water was never turned on. Turned on water. All functions tested good. Drain pipe is clogged. Water immediately came out of drain pipe. Instructed customer on having clog removed before operation of washer.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ03
Near Easley, SC 29642
Frank
Job Details: 07/07/2023
Resivour leaking when filter is in.. quoted 525.22 paid 262.61.. owe 262.61; ordrng 1 W11346622 (Resivour) and 1 Jobcodeu18 (Job code u18)
We serviced a
WHIRLPOOL RANGE
Model WFE505W0JZ3
Near Easley, SC 29640
Frank
Job Details: 07/07/2023
Installed board tested working ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Powdersville, SC 29642
Flint
Job Details: 07/07/2023
"Replaced broken element, and put thru a test cycle. The unit tested good."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Easley, SC 29640
Frank
Job Details: 07/07/2023
"No errors on unit.. increased rinse aid amount in , ran through diagnosis. Tested working ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDHB02
Near Lyman, SC 29365
Cliff
Job Details: 07/07/2023
"Lights in both sections are bad, I was able to replace the freezer today and customer wants to order the fresh food as well, total for both modules is 433.22, customer paid 216.61 today and will owe 216.61 once job has been completed.; ordrng 1 W11527432 (Module) and 1 L14jobcode (L14 job code)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT518SZFM00
Near Easley, SC 29640
Frank
Job Details: 07/07/2023
Intermittent turning off not cooling then cooling could be in cabinet wire harness or board.. quoted 408 for board replacement.. may call back to repair..
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Inman, SC 29349
Derek
Job Details: 07/07/2023
"Found unit stuck in spin when trying to agitate so whole tub moves. Unit had same issue previously and has had correct actuator installed. Found shield missing and pulley has been rubbing pan unit sits in from tub sag. Replaced actuator and cam. Unit agitating properly. Needs shield. J13; ordrng 1 WPW10427633 (Shield), used 1 W10913953 (Actuator), and 1 W10721967 (Cam) from stock"
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Leicester, NC 28748
Kari
Job Details: 07/07/2023
"Took quick pics, found unit not agitating, unit will just move basket and drain and sit. Found the shifter arm was missing. Installed new shifter. Ran diagnostic test. Unit checks ok ; used 1 W10913953 (Shifter) from stock"
We serviced a
WHIRLPOOL DISHWASHER
Model KDTE104KPS1
Near Inman, SC 29349
Cliff
Job Details: 07/07/2023
"Found the front right leg will not stay down, whenever I adjusted it out further it would slip back up inside support, ordering part.; ordrng 1 W10920120 (Support) and 1 N15jobcode (N15 job code) and 1 W11561254 (Leg)"
We serviced a
WHIRLPOOL OVEN
Model KSDG950ESS1
Near Gaffney, SC 29341
Cliff
Job Details: 07/07/2023
"Unit is giving the stuck key error code and the sound does not working for button presses, giving customer an estimate of 805.99 for the new console, customer wants to reach out to manufacturer to see if they will help. 1-800-253-1301"
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Gaffney, SC 29341
Cliff
Job Details: 07/07/2023
"Found the front right leg needed to be adjusted down slightly, I was able to run a drain and spin cycle with 4 wet towels with no issue."
We serviced a
WHIRLPOOL RANGE
Model WEE745H0LZ3
Near Pickens, SC 29671
Frank
Job Details: 07/07/2023
Found terminal block and cord melted. Needs block and cord. Customer will pick up cord to replace.; ordrng 1 WPW10245259 (Terminal block) and 6 WP3400029 (Nut)s and 1 Jobcodel14 (Job code l14)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ04
Near Salem, SC 29676
Frank
Job Details: 07/07/2023
Installed check valve.. tested working ok not leaking
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Anderson, SC 29626
Jerry D.
Job Details: 07/07/2023
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Easley, SC 29642
Flint
Job Details: 07/07/2023
"Found the working as designed, put thru a test cycle and filled and drained and spun, readjusted clothes and advised about loading in loose heaps. Unit tested good."
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Greenville, SC 29605
Flint
Job Details: 07/07/2023
"Found the unit working as designed, adjusted one leg and an thru a load of towels and blankets, and it was a little loud but it is as good as it can get, loading is going to be crucial"
We serviced a
FRIGIDAIRE FREEZER
Model LFFU1465DW6
Near Greenville, SC 29609
Flint
Job Details: 07/07/2023
"Insufficient compresssor, seals bad, needs new compressor,estimate is 1500. Customer will buy new"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Greenville, SC 29605
Carl
Job Details: 07/07/2023
Installed new adjuster kit unit ck ok
We serviced a
MAYTAG DRYER
Model MEDX6STBW1
Near Simpsonville, SC 29680
Carl
Job Details: 07/07/2023
Found heater open i stalled new pre id part reassembled cycled unit heater shorted out will order f13; ordrng 1 279838 (Heater)
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Simpsonville, SC 29680
Carl
Job Details: 07/07/2023
Ran diagnostics found error codes found lower harness has several wires open n15; ordrng 1 W11643701 (Lower harness) and 1 N15 (Labor)
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FGHC234LF1
Near Simpsonville, SC 29681
Carl
Job Details: 07/07/2023
Found defrost drain used steam to clear unit ck ok
We serviced a
WHIRLPOOL WASHER
Model MVWC565FW2
Near Anderson, SC 29625
Jerry D.
Job Details: 07/07/2023
She called back later and cancelled
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT112CZJW00
Near Spartanburg, SC 29303
Derek
Job Details: 07/07/2023
Defrost drain tube frozen again. Removed ice and melted ice in tray then thawed drain. Water flowing rapidly into pan so drain clear. Heater has a tab which holds heater down close to drain and it was not looped over heater and heater sitting too far above drain to prevent freezing. Unit checks ok.
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW3
Near Simpsonville, SC 29681
Carl
Job Details: 07/07/2023
"Installed new spluch, cap and belt ran diagnostics and a test cycle to ck operation unit ck ok"
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Spartanburg, SC 29301
Tyler
Job Details: 07/07/2023
F8e1 error code. Found water was never turned on. Turned on water. All functions tested good. Drain pipe is clogged. Water immediately came out of drain pipe. Instructed customer on having clog removed before operation of washer.
We serviced a
AMANA REFRIGERATOR
Model ASI2175GRS07
Near Spartanburg, SC 29306
Tyler
Job Details: 07/07/2023
"Found control has double stickers on it. Per TECHLINE, defrost algorithm is incomplete in these controls.; ordrng 1 W11546609 (Control)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRB322DMBM03
Near Cowpens, SC 29330
Tyler
Job Details: 07/07/2023
Evap fan making intermittent noise.; ordrng 1 WP2169142 (Fan) and 1 WPW10128551 (Motor) and 1 L14jobcode (L14 job code)
We serviced a
WHIRLPOOL MW OVEN COMBO
Model WOC54EC0HS04
Near Cowpens, SC 29330
Tyler
Job Details: 07/07/2023
"Microwave not detecting door opening or shutting. Unit is against a wall, will need helper.; ordrng 1 W11033422 (Interlock switch) and 1 2manjob (2 man job)"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Cowpens, SC 29330
Tyler
Job Details: 07/07/2023
"Installed part, all functions tested good."
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ1
Near Gaffney, SC 29341
Tyler
Job Details: 07/07/2023
"Called TECHLINE, they advised coin box lock has to be drilled out. Broke all my drill bits. ; ordrng 1 Supervisoronly (Supervisor only)"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706ESS01
Near Chesnee, SC 29323
Tyler
Job Details: 07/07/2023
Customer had icemaker issues. Had power outage. Reset unit. All functions tested good.
We serviced a
WHIRLPOOL WASHER
Model WTW7600XW2
Near Anderson, SC 29625
Jerry D.
Job Details: 07/07/2023
"In test mode 3 codes, F51 rotor, F2, Cntrl, f80 lock, unit wont run , panel flashes and goes out, volts and polarity good, spinning basket by hand and bearings are loud, ordering,Q16; ordrng 1 Q16 (Q16) and 1 W10178988 (Rps) and 1 W10059230 (Lock) and 1 W10059230 (Lock) and 1 W10372181 (Cntrl) and 1 W10211351 (Console) and 1 8565177 (Rotor) and 1 W10193886 (Tub)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ02
Near Fountain Inn, SC 29644
Jerry D.
Job Details: 07/07/2023
"Installed listed parts cycled unit through test and all functions are working properly, customer paid balance, 200.00, cc. 4028292892"
We serviced a
WHIRLPOOL KITCHEN
Model WDP540HAMZ0
Near Simpsonville, SC 29680
Jerry D.
Job Details: 07/07/2023
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ03
Near Simpsonville, SC 29680
Jerry D.
Job Details: 07/07/2023
"Compressor inoperable, ordering, Q16; ordrng 1 Q16 (Q16) and 1 Wpw10143759 (Drier) and 1 W11574734 (Compressor)"
We serviced a
KITCHEN AID REFRIGERATOR
Model KFIS29PBMS03
Near Simpsonville, SC 29680
Jerry D.
Job Details: 07/07/2023
"Found liner warped, freez door not sealing, not repairable"
We serviced a
WHIRLPOOL WASHER
Model MVW5430MW0
Near Asheville, NC 28803
Kari
Job Details: 07/07/2023
Installed parts unit checks ok
We serviced a
WHIRLPOOL WASHER
Model WFW5605MC0
Near Swannanoa, NC 28778
Kari
Job Details: 07/07/2023
"Took quick pics, found u it showing 9-1 long drain code. Found when you toggle drain pump it sounds like its on but no water moves. Found that the impeller head broken off of the shaft and it was just really spinning in housing. Vacuumed out all water installed new pump ran diagnostic cycle unit checks OK?"