We serviced a
KITCHENAID REFRIGERATOR
Model KBSD602ESS01
Near Asheville, NC 28803
Brian
Job Details: 07/19/2023
Installed all new led modules. Tested and found all operations ok at this time. Did not move unit.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT518SZFM00
Near Gaffney, SC 29341
Matt
Job Details: 07/19/2023
Found unit had leak in evaporator and compressor is noisy. Replaced compressor and evaporator also added A u.v dye drier. Pressure tested. Unit held pressure. Pulled a vacuum and weighed in 4.3 ounces of 134a. Good frost pattern on evaporator. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRMF706ESS05
Near Chesnee, SC 29323
Cliff
Job Details: 07/19/2023
"Fresh food temp was 40 without any items in section and setting at 35, the freezer was 0 set to 0, the RC evaporator thermistor showed open on test 39, so i got to it to check it manually, it showed it was good with my meter, I had to unplug it to test and when I plugged it back in I made sure it was tight, I also taped and zip tied thermistor to tubing because it was loose, checked test 39 again and it showed an 01 which is a pass"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHB08
Near Chesnee, SC 29323
Cliff
Job Details: 07/19/2023
"Found evaporator frozen over, the defrost heater worked in diagnostics, he thermistor was out of range so I replaced that, zip tied to tubing, all functions check ok check ok as of now; used 1 WPW10384183 (Thermistor) from stock"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF518SAHM
Near Zirconia, NC 28790
Derek
Job Details: 07/19/2023
"Found no water supply to unit and is programmed to attempt fill for 4 min at which time if flow meter has not seen sufficient water it will code out with E1 no water error and run drain pump, which unit was doing. Supply hose was flood safe hose with directional flow and installed backwards. Uninstalled unit and switched hose around. Cycled unit uninstalled to leak check. No leak found and unit operating normally. Called safety team to report findings."
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Fountain Inn, SC 29644
Carl
Job Details: 07/19/2023
Adjusted sleaves on hinges need consol cant use start key; ordrng 1 W11612307 (Console blk) and 1 J13 (Labor)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Anderson, SC 29626
Jerry D.
Job Details: 07/19/2023
"Temps 36@1, Imk thermistor wire hanging down, installed imk sent preid, cycled unit through test and all functions are working properly"
We serviced a
KITCHEN AID REFRIGERATOR
Model KFIV29PCMS02
Near Alexander, NC 28701
Derek
Job Details: 07/19/2023
Installed parts. Pulled vacuum. Charged unit with 5.5 oz of 134a. Cycled unit. Unit cooling and checks ok.
We serviced a
WHIRLPOOL ICEMAKER
Model WRS315SDHM08
Near Fountain Inn, SC 29644
Carl
Job Details: 07/19/2023
Found water fill tube not properly installed removed imk and adjusted fill tube rinstalled imk cycled all of the water went into the mold unit ck ok
We serviced a
WHIRLPOOL RANGE
Model WFG320M0BS3
Near Fountain Inn, SC 29644
Carl
Job Details: 07/19/2023
Found door damaged installed new glass unit ck ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADB7
Near Mauldin, SC 29662
Carl
Job Details: 07/19/2023
Installed new sump and control ran diagnostics and a test cycle to ck operation unit ck
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ01
Near Inman, SC 29349
Cliff
Job Details: 07/19/2023
"Found ice build up around ice maker, cleared away ice, cycled the ice maker and watched the fill, advised to keep an eye for more ice build up, but all functions check ok as of now."
We serviced a
WHIRLPOOL WASHER
Model WTW5100HC2
Near Greer, SC 29651
Chris
Job Details: 07/19/2023
"Found oil covering Motor and components . Presumably, coming from gearbox. Replace gearbox from stock. Unit check is OK. Double labor authorization is w17v8f1nl2; used 1 W11449840 (Gearcsse), and 1 W11026785 (Motor) from stock"
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Greer, SC 29651
Chris
Job Details: 07/19/2023
Unit has vent restriction. Heater grounded and all fuses open. Replaced from stock . Unit check is ok . Advised customer to have vents checked due to poor airflow
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Greenville, SC 29605
Flint
Job Details: 07/19/2023
"Found 120 on each leg, no 240 across, will need an electrician"
We serviced a
MAYTAG WASHER
Model MHW5630HC0
Near Leicester, NC 28748
Kari
Job Details: 07/19/2023
"Two quick pics found unit showing an F08 E2 over suds code. Ran unit three diagnostic cycle found all functions complete customer has had water running out of the back vent tube defined as a vent tube on top is wet after I took the top off at the customer the customer said that it was attached to the housing while it was leaking rain unit through a heavy duty cycle found that some water did come out, connected hose back to housing and sealed with rtv to prevent leaking. Make sure the unit was level. Also talk to customer about the dispenser, possibly leaking because the dispenser is the old style with the slats in the front not the holes. told customer to wait at least an hour for the silicone to dry before doing laundry. Had office run cc for $199.99 for TC and labor. Emailed receipt"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Greenville, SC 29607
Flint
Job Details: 07/19/2023
"Found the wheel broken, needs adjusters; ordrng 1 W10712395 (Adjusters)"
We serviced a
WHIRLPOOL LAUNDRY CENTER
Model MVW7232HW1
Near Simpsonville, SC 29681
Flint
Job Details: 07/19/2023
"Found bolt had fallen out of stator, resecured bolt with loc tight, pump had debris in it, cleaned out and filled unit to test, unit tested good at this time."
We serviced a
WHIRLPOOL DRYER
Model WED5100HW2
Near Weaverville, NC 28787
Kari
Job Details: 07/19/2023
"Took quick pics, found a mouse had placed a bunch of cat food and other stuff in the heater housing, took unit apart and customer vaccumed bottom of unit out. Put back together heater housing and cleared debris from air channel above heater. Put everything back together and ran unit on medium. Unit smells normal now but advised customer run it about 15-30 minutes before they put clothes in to make sure the smell is gone. Had office run cc for TC and labor of $199.99. Emailed receipt"
We serviced a
MAYTAG OVEN
Model MEW7530DS00
Near Weaverville, NC 28787
Kari
Job Details: 07/19/2023
"Took quick pics, found unit panel was on but wouldnt heat in bake or broil, took unit out and had customer flip breaker off. Took back off and did resistance checks. Found the bake element to have 19 ohms, the broil element to have 22 ohms the temp probe is at 1.1 kohms. TOD and ui fuses are closed and look good. Had customer turn breaker back on and I wasnt getting voltage to outlet. Found breaker now wont turn all the way on and will sit in the middle. Tried resetting breaker by flipping it a few times and it wont fully turn on. Told customer I believe the breaker is bad and was only sending 120v to power panel then by messing with it, it killed the other side and now we have no power to outlet. Advised customer get an electrician to change breaker and if they still have issues to call us back and we will recheck. Had office run cc for $150 and email receipt"
We serviced a
KITCHEN AID RANGE
Model KFEG504KPS3
Near Weaverville, NC 28787
Kari
Job Details: 07/19/2023
"Took quick pics, found the inner part of the LF element not coming on. Need switch for repair ; ordrng 1 J13 (Job code) and 1 Bringpartswithme"
We serviced a
MAYTAG WASHER
Model MVWC416FW1
Near Mars Hill, NC 28754
Kari
Job Details: 07/19/2023
"Took quick pics, found unti showing 8-1 low flow code. Customer had the well replaced in June. I think the old well had ruined the new valve I replaced 5/22 and now that they have a new well we shouldnt have this issue again installed new valve. Ran unit through diagnostics cycle. Unit checks ok; used 1 W11038689 (Valve) from stock"
We serviced a
WHIRLPOOL DRYER
Model MED5630HW2
Near Burnsville, NC 28714
Kari
Job Details: 07/19/2023
"Took quick pics, found unit not heating. Found unit on high just rolls cold air around. Took front off checked thermals and heater. Found thermals good but heater is showing open. Gave cust est of $323.96 at second appliance TC customer agreed. Installed heater unit now heats. Paid by check. Emailed receipt unit checks ok; used 1 WP3387747 (Heater) from stock"
We serviced a
AMANA WASHER
Model NTW4516FW3
Near Anderson, SC 29624
Jerry D.
Job Details: 07/19/2023
"Motor humming, volts good, installed capacitor sent preid, cycled unit through test and actuator clicking voltage good, installed actuator, cycled unit through test and unit checks ok"
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW3
Near Anderson, SC 29621
Jerry D.
Job Details: 07/19/2023
"Splutch and belt torn up, actuator recieving good power but clicking and not moving , installed listed part sent preid, also installed belt w11239857 from truck stock, cycled unit through test and all functions are working properly"
We serviced a
WHIRLPOOL WASHER
Model MVW7230HW1
Near Zirconia, NC 28790
Derek
Job Details: 07/18/2023
Found suspension ball cracked and back left suspension not attached to frame. Replaced suspension. Cycled unit. Unit checks ok. ; used 1 W11400156 (Suspension) from stock
We serviced a
WHIRLPOOL DRYER
Model MED4500MW0
Near Zirconia, NC 28790
Derek
Job Details: 07/18/2023
"Found blower grinding when cycled. Grinding w/ back blower cover off. Checked motor, motor good but front mount off cradle so motor too far back allowing blower to hit behind motor on housing. Secured motor in cradle properly. Cycled unit. Unit heating and checks ok."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Zirconia, NC 28790
Derek
Job Details: 07/18/2023
"Found unit did not complete cycle after last repair but no fault code stored. Put into service cycle. Drain pump started at beginning not the order test run in. Pressure hose not kinked and no cut or hole in hose found. Later when testing sensing light illuminated and unit sat with only that light on, wouldnt start and wouldnt cancel and turn light off. Ordering parts. N15; ordrng 1 W11481116 (Encoder) and 1 W11513246 (ACU) and 1 W11643701 (Harness) and 1 W11481722 (Actuator) and 1 W11399437 (Pump)"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FGHB2866PP6A
Near Greenville, SC 29607
Flint
Job Details: 07/18/2023
"Found evaporator fan not getting power, needs board, fan assembly and ui. Estimate is 1060, or 720.00 without the ui. Customer will look for new unit."
We serviced a
WHIRLPOOL RANGE
Model KSGB900ESS1
Near Greenville, SC 29601
Flint
Job Details: 07/18/2023
"Found f2e1 error, tried replacing with a control from another unit, it worked but didnt fit, swapped them back to their original unit, qouted 970 ."
We serviced a
WHIRLPOOL DISHWASHER
Model KDTE334GPS0
Near Greenville, SC 29601
Flint
Job Details: 07/18/2023
"Found wash motor not running, needs sump assembly. Qouted 639, customer paid 150.00. He will buy new"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ06
Near Belton, SC 29627
Jerry D.
Job Details: 07/18/2023
"Fan motor vibrating, door to low, ordering, j13; ordrng 1 2315549 (Motor) and 2 Wp487576 (Shims)s and 2 489467 (Shims)s"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Fountain Inn, SC 29644
Jerry D.
Job Details: 07/18/2023
"Cleared evap, installed listed parts, unit chks ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ03
Near Simpsonville, SC 29680
Jerry D.
Job Details: 07/18/2023
"Installed listed parts , pulled 30 inches of vaccum, vaccum is holding, charged unit 56 grams, lowside pressure is 3 psi, good frost pattern on evaperator temps coming down rapidly, unit chks ok"
We serviced a
WHIRLPOOL DISHWASHER
Model kdte204kps1
Near Piedmont, SC 29673
Jerry D.
Job Details: 07/18/2023
"Fill valve inoperable ordering , j13; ordrng 1 W11131184 (Valve)"
We serviced a
WHIRLPOOL KITCHEN
Model wrs315sdhm08
Near Piedmont, SC 29673
Jerry D.
Job Details: 07/18/2023
"Found filter valve humming and no water coming through, installed valve w11446818 from truck stock, cycled unit through test and no leaks found unit checks ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Spartanburg, SC 29301
Cliff
Job Details: 07/18/2023
"Customer has a data logger inside the fresh food section, the low was 50 and the high was 86, but the current temp is 36 with the temp setting at its highest. The customer explained that it seems to cut on and off, the evaporator is clear from frost build up and the freezer section has always worked. The thermistor for fresh food section was out of spec slightly, so I replaced it, advised customer to just watch and let us know if the issue happens again."
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706ESS01
Near Fletcher, NC 28732
Brian
Job Details: 07/18/2023
Customer had another company work on unit. Did not enter home did not service unit.
We serviced a
WHIRLPOOL RANGE
Model WFE525S0JZ3
Near Candler, NC 28715
Brian
Job Details: 07/18/2023
Installed front right switch. Tested and found all operations ok at this time.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ00
Near Mills River, NC 28759
Brian
Job Details: 07/18/2023
"Found some ice ball on evaporator and condensation on freezer ceiling. Found fan working properly. Found good frost pattern and heater working. It appears as if a door was left open. All gaskets ok and doors sealing properly. Removed ice ball. Installed new ice maker and tested, observing for leaks and proper functions. At this time, all operations ok with no leaks detected."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ07
Near Horse Shoe, NC 28742
Brian
Job Details: 07/18/2023
"Customer showed recording of noise coming from freezer compartment. Fan is running and no unusual noises. Tested ice maker and found it ok. Removed evap cover and found frost ball. Let unit run for about 20 min with door closed and found full frost pattern. Tested and found heater functioning. It appears that excess frost formed on evaporator, due to door not closing, from a previous issue. Removed ice build up and tested, observing for leaks and proper functions. At this time, all operations ok with no leaks detected."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF954CIHW00
Near Boiling Springs, SC 29316
Cliff
Job Details: 07/18/2023
"Replaced part, the ice that was in the ice tray either looked liked it was overfilling or melted, advised customer we may have to replace the ice maker as well. all functions check ok"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAKZ1
Near Duncan, SC 29334
Cliff
Job Details: 07/18/2023
"Found the disposal plug still in, knock out, ran an auto test, all functions check ok"
We serviced a
WHIRLPOOL DISHWASHER
Model KDTE104KPS1
Near Brevard, NC 28712
Brian
Job Details: 07/18/2023
"Tested unit in normal cycle and auto diagnostics. Unit completed in auto diagnostics. In normal cycle, as unit is filling, f8e1 (no water entering unit) error code is triggered. Replaced control and tested multiple times, in normal and auto diagnostics cycles and found error code no longer occurring. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF577KPS02
Near Brevard, NC 28712
Brian
Job Details: 07/18/2023
"Found e5 (ice maker thermistor is bad) error code. Test cycled ice maker and Found fill tube frozen. Found fill tube heater not getting voltage, when activated. Replaced ice maker and thawed fill tube. Checked and found error code now gone. Cycled and filled ice maker. Ice maker completing cycle Now found fill tube heater coming on and getting proper voltage. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ00
Near Cedar Mountain, NC 28718
Brian
Job Details: 07/18/2023
Found e1 (no cool). Test cycled ice maker and found it completing cycle. Found fresh food evaporator frozen over. Also found drip pan warped and ice bin cracked. Found service pointer regarding frozen evaporator. Pan (W11457241)Evap cover (W11188493)Evaporator fan (W11087438) User interface (W11387386) Ice bin (WPW10347093) and Main control (W10843055) needed. ; ordrng 1 W11457241 (Pan) and 1 W11188493 (Evaporator cover) and 1 W11087438 (Evaporator fan) and 1 W11387386 (User interface) and 1 WPW10347093 (Ice bin) and 1 U18 (Job code) and 1 W10843055 (Main control)
We serviced a
KITCHEN AID REFRIGERATOR
Model KSCS25FTSS01
Near Duncan, SC 29334
Cliff
Job Details: 07/18/2023
"Unit was not running when I arrived, I tried powering unit off for a couple of minutes and back on, the control in the roof of the fresh food section is beeping and the temp settings keeping changing to different numbers and the light will flash, the control(WP2307037) in that section is no longer available and there isnt a kit for it either from what I can see."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Franklin, NC 28734
Kari
Job Details: 07/18/2023
Took quick pics found unit not filling and shows 8-1 code. Found the cold valve to be impacted with sediment. Couldnt get screen out to clean it. Installed new valve. Unit checks ok; used 1 W11210459 (Valve) from stock
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Cullowhee, NC 28723
Kari
Job Details: 07/18/2023
"Took quick pics, found unit not starting. Found the unit would just shut off. After customer started cycle. Found the door latch open either way. Installed new latch. Unit checks ok; used 1 WPW10653840 (Latch) from stock"
We serviced a
WHIRLPOOL MW OVEN COMBO
Model WOC75EC0HS20
Near Franklin, NC 28734
Kari
Job Details: 07/18/2023
"Took quick pics, found unit showing 6-1 over temp code. Found the temp sensor showing infinite resistance. Installed new pride. Ran bake cycle to 350 with an average temp of 351.6 degrees. Unit checks ok"
We serviced a
WHIRLPOOL WASHER
Model WFW85HEFW1
Near Greenville, SC 29601
Flint
Job Details: 07/18/2023
"Needs water level switch, additional 195.00 will be due; saved tckt"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHB0
Near Mauldin, SC 29662
Flint
Job Details: 07/18/2023
"Replaced sump assembly and tested the unit tested good, no leaks"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS2623AW1
Near Greer, SC 29651
Chris
Job Details: 07/18/2023
Installed new parts. Unit check is ok
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KBL1
Near Greer, SC 29650
Chris
Job Details: 07/18/2023
"Installed new parts, unit check is ok"
We serviced a
MAYTAG WASHER
Model MVWC565FW1
Near Greer, SC 29651
Chris
Job Details: 07/18/2023
"Unit has large amount of oil coming from gear box. Oil has covered all components. Unit needs geaebox,cam,belt and capacitor. Gave customer a blue book estimate for repair with tax and shipping at $1307.08. Customer denied repair"
We serviced a
KITCHEN AID REFRIGERATOR
Model KSCS25FTSS01
Near Duncan, SC 29334
Cliff
Job Details: 07/18/2023
"Unit was not running when I arrived, I tried powering unit off for a couple of minutes and back on, the control in the roof of the fresh food section is beeping and the temp settings keeping changing to different numbers and the light will flash, the control(WP2307037) in that section is no longer available and there isnt a kit for it either from what I can see."
We serviced a
KITCHEN AID RANGE
Model KFGC558JSS01
Near Lake Toxaway, NC 28747
Frank
Job Details: 07/18/2023
Found igniter needed to be adjusted to spark onto burner .. tested working ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ00
Near Greer, SC 29651
Chris
Job Details: 07/18/2023
Unit is a rent a center product. Unit is no cool in both sections. Components damaged to major bug infestation. Documented bug infestation in quick pics entire unit/compressor area is infested with roaches. Called trade care and spoke with jasmine. File number for call is 736869887
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Franklin, NC 28734
Kari
Job Details: 07/18/2023
Took quick pics found unit showing off balance load code. Also find when you touch the unit it wobbles back-and-forth from left to right found that the back right foot has a crack in it and its not fully spinning due to the fact that the feet are not level and the machine is moving every time the tub spins installed new foot ran re-calibration unit checks OK; used 1 WPW10687506 (Foot) from stock
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Taylors, SC 29687
Chris
Job Details: 07/18/2023
Unit has broken belt and seized pulley. Gave customer a blue book estimate with tax and shipping for dryer repair kit at $404.17. Installed new parts. Unit check is ok
We serviced a
WHIRLPOOL WASHER
Model mvw4505mw0
Near Anderson, SC 29621
Jerry D.
Job Details: 07/18/2023
"Actuator getting good voltage and clicking, installed w10815026 from truck stock cycled unit through test and all functions are working properly"
We serviced a
WHIRLPOOL RANGE
Model WEE745HOLZ1
Near Anderson, SC 29625
Jerry D.
Job Details: 07/18/2023
"Right front burner open, switch inoperable, ordering, j13; ordrng 1 W11282542 (Burner r f) and 1 W10437092 (Switch)"
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Greenville, SC 29609
Flint
Job Details: 07/18/2023
"Replaced board and at first it tested good, but then started to do the same thing, I noticed the door switch acting up, and the ui , will order; ordrng 1 W11626080 (Ui) and 1 W11551763 (Door switch)"
We serviced a
WHIRLPOOL RANGE
Model WCG97US0HS05
Near Simpsonville, SC 29681
Carl
Job Details: 07/18/2023
Valve will only stay on hi n15; ordrng 1 W11256503 (Valve) and 1 N15 (Labor)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ02
Near Fountain Inn, SC 29644
Carl
Job Details: 07/18/2023
Installed new valve cycled imk got good fill ynit ck ok
We serviced a
KITCHEN AID RANGE
Model KSGB900ESS 4
Near Simpsonville, SC 29681
Carl
Job Details: 07/18/2023
Sr#7736882877 installed new dci and valve cycled unit to 350? and sill just sparks called tech line ran diagnostics was getting voltage and ohmed harness to the valve ck good he advised to reorder dci board ; ordrng 1 W10860916 (Dci board)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS322FDAM00
Near Taylors, SC 29687
Chris
Job Details: 07/18/2023
No show . Tagged door
We serviced a
MAYTAG DRYER
Model MGD7230HC2
Near Franklin, NC 28734
Kari
Job Details: 07/18/2023
Installed parts unit checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Simpsonville, SC 29681
Carl
Job Details: 07/18/2023
Cycled unit water valve reciving voltage Found water line from valve to tank twisted corrected cycled unit got a good fill
We serviced a
WHIRLPOOL FREEZER
Model WZC3122DW01
Near Simpsonville, SC 29680
Carl
Job Details: 07/18/2023
Found bad compressor advised customer and she will let us know
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Sylva, NC 28779
Kari
Job Details: 07/18/2023
"Took quick pics, found unit would just spin continuously. Found capacitor was leaking oil but after I changed the capacitor it kept spinning uncontrollably. Found unit showing f2e3 encoder miscommunication to acu code need boards for repair. ; ordrng 1 W11481116 (Encoder) and 1 W11513246 (Acu) and 1 J13 (Job code), used 1 W11395618 (Capacitor) from stock"
We serviced a
WHIRLPOOL WASHER
Model MVW7232HW1
Near Zirconia, NC 28790
Derek
Job Details: 07/18/2023
Installed parts. Cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL KITCHEN
Model WDT740SALZ0
Near Zirconia, NC 28790
Derek
Job Details: 07/18/2023
Installed parts. Cycled unit. No leaks. Unit checks ok.
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Sylva, NC 28779
Kari
Job Details: 07/18/2023
"Took quick pics, found unit made a loud pop and then wouldnt spin. Found unit showing basket re-engagement fault when I tip the unit up I found that the ring of the cam it snapped in half so the ring was hanging on the actuator arm, detached from the rest of the ring. Installed new cam Unitchekcs OK"
We serviced a
WHIRLPOOL WASHER
Model MVWC565FW2
Near Zirconia, NC 28790
Derek
Job Details: 07/18/2023
Installed parts. Cycled unit. Unit checks ok.
We serviced a
MAYTAG WASHER
Model MVW6230HW
Near Boiling Springs, SC 29316
Derek
Job Details: 07/17/2023
"Found actuator arm broken and unit staying in the spin position when trying to agitate. Faults stored were F0E3, F0E4, F7E7, F7E6, F7E1. Cleared faults. Replaced parts. Cycled unit. Spin and agitation working properly. Unit checks ok."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Gaffney, SC 29341
Derek
Job Details: 07/17/2023
Installed water valve. Cycled unit. Unit checks ok
We serviced a
KITCHEN AID RANGE
Model KFGS530ESS2
Near Greenville, SC 29607
Cliff
Job Details: 07/17/2023
"Talked to Robert from techline, 7736160832, he again said there is nothing we can do, that the cavity will make noise while it is expanding. The igniter works fine, it ignites the burner immediately so there is no gas build up, all functions check ok."
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Easley, SC 29640
Cliff
Job Details: 07/17/2023
"Replaced part, was able to turn the timer, all functions check ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDW09
Near Easley, SC 29640
Flint
Job Details: 07/17/2023
"Found ice buildup all over the evaporator coil, found a wire was not locked into the molex plug, reattached and it locked in place. Thawed all the ice buildup and the unit tested good."
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Greenville, SC 29611
Flint
Job Details: 07/17/2023
"Found the unit working as designed, put through a test cycle and the unit tested good at this time. Found the drain hose at 32 inches high it needs to be at 39 inches minimum. Advised to add to the drain line so it can be lifted up to at least 39 inches from the floor."
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZ0
Near Greenville, SC 29607
Flint
Job Details: 07/17/2023
"Replaced parts and tested, the unit tested good, no leaks."
We serviced a
JENN-AIR VENTHOOD
Model JXW8536HS1
Near Greenville, SC 29601
Cliff
Job Details: 07/17/2023
"Replaced parts, all functions check ok"
We serviced a
WHIRLPOOL LAUNDRY CENTER
Model mvwc565fw3
Near Taylors, SC 29687
Derek
Job Details: 07/17/2023
Found F5E1 lid switch fault only code stored. Unit thinks lid is up. Replaced lid lock. Cycled test mode. Al!functions of unit checks good. ; used 1 W11307244 (Latch) from stock
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Candler, NC 28715
Kari
Job Details: 07/17/2023
"Took quick pics, found unit showing F0E3 mechanical friction, cleared code ran unit through diagnostics cycle. Found it fills and drains fine but the agitator makes a sqealing noise and when its spinning it sounds like something is dragging when tub spins. Took rotor off and found it filled with gearcase oil. Need gearcase for repair for noise also found this model is in the serial break for the redesigned tub ring. Ordering updated tub ring to prevent leaking in the future. ; ordrng 1 W11449841 (Gearcase) and 1 W10734521 (Slider) and 1 W11590590 (Tub ring) and 1 N15 (Job code)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ07
Near Greenville, SC 29615
Cliff
Job Details: 07/17/2023
"Found a couple of cubes caught between the fingers on ice maker keeping it from cycling through, removed cubes, ice maker dumped the ice that was in tray and filled with water, freezer temp is 0 set to 0, fresh food temp is"
We serviced a
WHIRLPOOL WASHER
Model WTW7000DW1
Near Simpsonville, SC 29681
Carl
Job Details: 07/17/2023
".installed new gearcase,stator,rotor,slider rn diagnostics and a test cycle to ck operation unit ck"
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS0
Near Simpsonville, SC 29681
Carl
Job Details: 07/17/2023
Installed new dispenser ran diagnostics unit ck ok
We serviced a
WHIRLPOOL DISHWASHER
Model GU2700XTSB0
Near Simpsonville, SC 29680
Jerry D.
Job Details: 07/17/2023
"Found motor capacitor damaged in box and broken, reordering, j13; ordrng 1 Wpw10780877 (Sump and motor assy)"
We serviced a
WHIRLPOOL FREEZER
Model WZF34X18DW03
Near Simpsonville, SC 29681
Carl
Job Details: 07/17/2023
Installed new limit cycled unit ck ok
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW0
Near Greenville, SC 29615
Chris
Job Details: 07/17/2023
Unit has no stored faults. Suspension is good and firm. Unit is planted . Liquid wash ring is present in wash basket. Unit passes auto diagnostics. Calibrated unit. Unit check is ok
We serviced a
WHIRLPOOL DRYER
Model WED4850HW0
Near Greenville, SC 29615
Chris
Job Details: 07/17/2023
"Unit has worn rollers. Gave customer a bluebook estimate for repair at $373.41. Installed new parts, unit check is ok."
We serviced a
KITCHENAID REFRIGERATOR
Model WRF757SDHZ04
Near Greer, SC 29650
Chris
Job Details: 07/17/2023
Found bleeding valve. Replaced valve. Unit check is ok. No leaks
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ03
Near Easley, SC 29642
Frank
Job Details: 07/17/2023
Replaced reservoir.. tested working ok
We serviced a
MAYTAG WASHER
Model MVWC565FW3
Near Inman, SC 29349
Derek
Job Details: 07/17/2023
"Installed parts. Cycled full auto test, then actual rinse spin. All functions of unit checks good."
We serviced a
KITCHEN AID REFRIGERATOR
Model KFIS20XVMS11
Near Inman, SC 29349
Derek
Job Details: 07/17/2023
Installed paddle. Cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL REFRIGERATOR
Model ED5FHAXVB00
Near Simpsonville, SC 29681
Carl
Job Details: 07/17/2023
Installed new optics unit diagnostics says new optic are bad and ck imk and found motor open; ordrng 1 8021515 (Module) and 1 W10757851 (Optics)
We serviced a
MAYTAG DRYER
Model MEDX6STBW1
Near Simpsonville, SC 29680
Carl
Job Details: 07/17/2023
Installed new element cycled unit to ck operation unit ck ok
We serviced a
WHIRLPOOL DRYER
Model MED6230HW3
Near Hendersonville, NC 28791
Brian
Job Details: 07/17/2023
Installed user interface. Tested unit and found all operations ok at this time. Customer had vent line cleaned and airflow is now ok.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FBS04
Near Pisgah Forest, NC 28768
Brian
Job Details: 07/17/2023
"Removed all ice build up and installed ew evaporator cover. Found interior lights now not coming on. Put old evap cover on and found lights working. New evaporator cover faulty. Door ui (W11574767) Rear control (W11664342) and Evap cover (W11610999) needed ; ordrng 1 W11610999 (Evap cover) and 1 W11574767 (Door ui) and 1 W11664342) (Main,control)"