We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFC302ESS06
Near Waynesville, NC 28785
Kari
Job Details:
08/10/2023
Installed parts. Unit checks ok
We serviced a
WHIRLPOOL RANGE
Model WEG750H0HZ5
Near Waynesville, NC 28785
Kari
Job Details:
08/10/2023
"Took quick pics, Found units right front burner. The outer office has been chewed up so badly that pieces of the brass him actually moved to where he couldnt pull it out of the orfice holder. N Need orifice holder for repair. Customer has LP orfice; ordrng 1 W11550541 (Burner head kit for RF) and 1 N15 (Job code)"
We serviced a
KITCHEN AID REFRIGERATOR
Model KFCO22EVBL1
Near Waynesville, NC 28786
Kari
Job Details:
08/10/2023
"took quick pics, found units lower pantry door cover was missing and the left pantry bracket was missing the peg to hold the cover gave est for just parts and labor of $234.28 Customer agreed will order pantry, cover, and left bracket for repair; ordrng 1 WP12656822 (Pantrycover) and 1 L14 (Job code) and 1 WPW10122078 (LH pantry bracket)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM08
Near Simpsonville, SC 29680
Derek
Job Details:
08/10/2023
Installed parts. Cycled unit. Unit checks ok.
We serviced a
KITCHEN AID ICE MACHINE
Model KUIX535HPA00
Near Greenville, SC 29605
Derek
Job Details:
08/10/2023
Found bin overfilled with ice. In ice original bin thermistor reads 7.5k ohms new bin thermistor reading 8.5K. Thermistor out of range. Replaced with preid part. Cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Greenville, SC 29605
Derek
Job Details:
08/10/2023
Installed parts. Cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Greenville, SC 29609
Derek
Job Details:
08/10/2023
Found unit feet off level creating a lot of tub wobble and hoses bouncing off the back of unit creating a lot of noise. Pulled out and leveled properly. Also added some absorbent material to minimize any sound created from hoses hitting back wall. Cycled spin. Tub not out of round spinning smooth. Suspension checks good with no bounce. Advised customer of proper loading and operation for optimum performance. Unit checks ok.
We serviced a
WHIRLPOOL WASHER
Model MVW4505MW0
Near Greenville, SC 29617
Derek
Job Details:
08/10/2023
Customer concerned unit had a problem due to noise during cycle. Cycled diagnostics. No fault. Cycled full test mode. Customer mentioned drain pump sound and motor sound during agitation and spin. All 3 were normal sound levels and noises from unit. Calibrated unit. Advised customer of proper loading and operation for optimum performance. Unit checks ok.
We serviced a
KITCHEN AID REFRIGERATOR
Model KSRS25ILSS03
Near Flat Rock, NC 28731
Brian
Job Details:
08/10/2023
Installed new ice maker. Test cycled observing for leaks and proper functions. At this time all operations ok with no leaks detected. Did not move unit.
We serviced a
MAYTAG RANGE
Model MER7700LZ2
Near Taylors, SC 29687
Derek
Job Details:
08/10/2023
Installed parts. Cycled unit on bake 350? and checked calibration. Unit cycling in normal range. Unit checks ok.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ02
Near Greer, SC 29650
Derek
Job Details:
08/10/2023
Unit did have E2 error code stored. Installed parts. Cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHB4
Near Spartanburg, SC 29303
Chris
Job Details:
08/09/2023
Installed new parts. Unit check is ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ08
Near Fletcher, NC 28732
Derek
Job Details:
08/09/2023
Installed parts. Cycled unit. Unit checks ok.
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Seneca, SC 29678
Frank
Job Details:
08/09/2023
Timer hard to turn causing plastic on knob to break ordering timer and knob; ordrng 1 W11685947 (Timer)
We serviced a
WHIRLPOOL RANGE
Model WFG320M0BS3
Near Seneca, SC 29678
Frank
Job Details:
08/09/2023
GLO bar intermittent not coming back on after light.. weak.. dropping in voltage; ordrng 1 W11176454 (Ignitor) and 1 Jobcodel14 (Job code l14) and 1 W11126814 (Control)
We serviced a
MAYTAG DRYER
Model MED7230HW0
Near Salem, SC 29676
Frank
Job Details:
08/09/2023
Tried control. Still saying turn knob to cycle.. tried different cycles. Tried diagnostics mode. Would not go into.. need ui console; ordrng 1 W11413567 (Ui pane) and 1 Jobcodj13 (Job code j13)
We serviced a
WHIRLPOOL KITCHEN
Model WDF520PADM7
Near Laurel Park, NC 28739
Derek
Job Details:
08/09/2023
Unit had 4-3 wash motor error code and wash motor not running. Motor buzzes when trying to run. Also found broken friction pad. Unit needs wash motor and friction sleeves. Will order. L14; ordrng 2 WP8268961 (Friction pad)s and 1 W11025157 (Pump motor assy)
We serviced a
KITCHEN AID REFRIGERATOR
Model KSRG25FKSS16
Near Greenville, SC 29605
Chris
Job Details:
08/09/2023
Ice bin will not sit and lock on door. No damage to bin or door. Troube shot augar by flipping washers on shaft no difference . Advised customer unit may need bin and is hard to tell if bin will resolve problem without another bin to test.. gave customer a bluebook estimate for repair with tax and shipping $653.56. Customer denied repair .
We serviced a
JENN AIR OVEN
Model JJW2830DS01
Near Six Mile, SC 29682
Frank
Job Details:
08/09/2023
Replaced console.. set up tested working ok.. panel damage in box.. took 10 percent off price.. paid 505$
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Alexander, NC 28701
Kari
Job Details:
08/09/2023
"Took quick pics, found unit stuck in a safety loop. Let unit run until it cut off, put unit into diagnostics, found no codes, ran unit through recalibration and a diagnostic cycle, unit checks ok. Had office run cc for $125 and email receipt"
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ1
Near Alexander, NC 28701
Kari
Job Details:
08/09/2023
"Took quick pics, found unit missing parts and damaged to the point it looks like it was dropped off a fork lift and rolled down a hill. Took pictures of all the damage. Called JR and he called Andy to see if this would be covered other than the door, since this is not regular functional damage. Would need middle spray arm, pump assembly rollers for the rails, inner door, outer door, console, vent assembly, pump filter, drain pump, owi sensor, and latch. Customer said hell take it back to Lowes."
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Boiling Springs, SC 29316
Cliff
Job Details:
08/09/2023
"Unit is heating ok, temp set to high on timed dry, with vent connected, using my thermal coupler the temp got up to 187 before dropping down by one degree at a time, I told her that she has a restriction in her venting and would need them cleaned out, temperature on unit is ok. All functions check ok"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Mars Hill, NC 28754
Kari
Job Details:
08/09/2023
Installed parts unit checks ok
We serviced a
WHIRLPOOL ICE MACHINE
Model KUIX335HPS00
Near Lake Lure, NC 28746
Brian
Job Details:
08/09/2023
"Test cycled unit and found fan working ok. Unit filling and properly. Found a good frost pattern on evaporator plate and hot gas valve ok. Circulation and drain pump ok at this time. Heating grid ok. Tested bin thermistor and found it reading 2.84k when it should be reading 7.4k. New bin thermistor (WPW10511923) needed. Quoted customer 324.56 to complete repairs. Cu did not wish to proceed with repairs at this time. Collected 150 for service call. No leaks detected, did not move unit."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SNHM07
Near Spartanburg, SC 29302
Cliff
Job Details:
08/09/2023
"Ice bin was full of ice, ice maker is working as of now, all functions check ok."
We serviced a
KITCHENAID REFRIGERATOR
Model KRSF505ESS01
Near Greer, SC 29651
Matt
Job Details:
08/09/2023
Replaced compressor and drier filter as well as fresh food evaporator. Pressure tested. No leaks. Pound vacuum and weighed in 5.75 ounces of 134a. All functions pass in test 4.
We serviced a
JENN-AIR REFRIGERATOR
Model JFX2897DRP02
Near Seneca, SC 29672
Matt
Job Details:
08/09/2023
"Recovered refrigerant. Replaced drier,RC evaporator,and three way valve and die drier. Pressure tested to 140 psi then vacuumed unit. Recharged unit with 5.5 ounces of R134A. Everything performing well at this time.; used 1 W11506635 (Port) from stock"
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Hendersonville, NC 28792
Brian
Job Details:
08/09/2023
"Could hear unusual scrapping noise when unit is started or stopping. Found blower wheel stripped on motor shaft. When inspecting, I found connector broken on main control. Motor (W11549461) control (W11525996) wheel (WP697772) and harness (WPW10298258) needed. ; ordrng 1 W11525996 (Control) and 1 W11549461 (Motor) and 1 WP697772 (Wheel) and 1 WPW10298258 (Harness) and 1 4392067 (Repair kit) and 1 L14 (Job code)"
We serviced a
MAYTAG WASHER
Model MVWB835DW4
Near Hendersonville, NC 28792
Brian
Job Details:
08/09/2023
Customer did not receive outer tub. Spoke with JR and he Is going to look into situation and reschedule with customer. ; saved tckt
We serviced a
WHIRLPOOL COOKTOP
Model JGD3536WS01
Near Greer, SC 29650
Carl
Job Details:
08/09/2023
"Ound shorted switch and bad spk mod j13 Wpw10239017,Wpw10475150 bal if call back is 414.62"
We serviced a
KITCHENAID DISHWASHER
Model KDFM404KPS1
Near Greenville, SC 29615
Carl
Job Details:
08/09/2023
Installed new rail stop unit ck ok
We serviced a
KITCHENAID DISHWASHER
Model KDPM604KPS0
Near Greer, SC 29651
Chris
Job Details:
08/09/2023
Installed new parts. Unit check is ok. Unit was installed upon arrival . Re installed unit. Customer will need to install toe plate. Customer has misplaced toe plate and will ever install himself . Unit check is ok
We serviced a
MAYTAG WASHER
Model MVWC416FW1
Near Mars Hill, NC 28754
Kari
Job Details:
08/09/2023
Took quick pics found unit showing an F 8 E1 code again also found unit showing F8 E3 code found the customer had to turn cold water off at tap because in the middle of a cycle and made a popping noise and then just kept running out to the point where it was about to overflow into the floor. found sediment buildup in solenoid and in the screen installed new valve ran recalibration and diagnostic cycle unit checks OK did suggest a customer since they just got a new well a couple months ago that maybe they put the pipe a little bit more down because she states of the house filters have to be changed weekly and I told her that seems a little excessive for what I know about house filters; used 1 W11210459 (Valve) from stock
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS1
Near Burnsville, NC 28714
Kari
Job Details:
08/09/2023
Took quick pics found gouges in the consul if you run your finger nail across in there deep scratches the one that is most concerning runs across the start button it looks as though it could crack overtime Installed parts unit checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAHZ0
Near Asheville, NC 28803
Derek
Job Details:
08/09/2023
Installed parts. Cycled unit multiple times. No leak found. Unit checks ok.
We serviced a
WHIRLPOOL N/A
Model WRF736SDAM14
Near Liberty, SC 29657
Frank
Job Details:
08/09/2023
Display hard to read needs new interface... Ice fills and comes out ok.. water when pressed can hear valve humming but not coming out.. ; ordrng 1 Jobcodeq16 (Job code q16) and 1 WPW10341329 (Dual valve) and 1 W10865826 (Valve) and 1 W10865869 (Ui) and 1 8212547r (Water line)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ03
Near Greenville, SC 29617
Chris
Job Details:
08/09/2023
"Installed new parts. Also found waterline kinked in door hinge. Uninstalled door and reinstalled door. Unit check is ok ,w184u51xpl2"
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Greer, SC 29650
Chris
Job Details:
08/09/2023
"Installed new parts, unit began high pitch noise once again . Called tech line and spoke with Chris. Advised chris parts have been changed multiple times. No other moveable parts to replace. Chris has no known issues or service pointers on this model .chris advised noise could be cosmetic . Chris advised since noise doesnt impact drying performance unit is working as designed for now . Noise is cosmetic noise and not a functional problem. Chris has no recommendations for remedy or complaint. Chris advised if noise returns for customer to contact customer service with File number call is 7737052608. Called trade care and spoke with terry . New labor authorization for failed part is w184tg1dl1."
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFF577KPS02
Near Belton, SC 29627
Jerry D.
Job Details:
08/09/2023
"Shelf crooked, ordering, j13; ordrng 1 W10737428 (Shelf tuck)"
We serviced a
MAYTAG WASHER
Model MVWX655DW2
Near Pauline, SC 29374
Cliff
Job Details:
08/09/2023
"Found unit will not spin properly, hub may be stripped, unable to get impeller out, will order parts.; ordrng 1 W10528947 (Hub) and 1 W10902814 (Washplate) and 1 N15jobcode (N15 job code)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Roebuck, SC 29376
Cliff
Job Details:
08/09/2023
"Same issue, reordering sump and ordering control; ordrng 1 W11613479 (Sump) and 1 W11637581 (Control) and 1 N15jobcode (N15 job code)"
We serviced a
KITCHEN AID DISHWASHER
Model KDTM704KPS0
Near Greer, SC 29651
Cliff
Job Details:
08/09/2023
"Replaced parts, ran an auto test, cycled a normal wash for 10 minutes to check for leaks and operation, all functions check ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model GI6FDRXXB01
Near Fountain Inn, SC 29644
Jerry D.
Job Details:
08/09/2023
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW1
Near Fountain Inn, SC 29644
Jerry D.
Job Details:
08/09/2023
"Suspension is loose, ordering, j13; ordrng 1 W11159470 (Suspension)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Simpsonville, SC 29680
Jerry D.
Job Details:
08/09/2023
"Connectors and tubing damaged, ordering, j13; ordrng 1 Wpw10334458 (Connector) and 1 2198677 (Connector) and 1 8201815 (Valve check) and 1 W11529425 (Tubing reservoir)"
We serviced a
KITCHEN AID RANGE
Model KSIB900ESS1
Near Simpsonville, SC 29680
Jerry D.
Job Details:
08/09/2023
"F2 , installed interface sent preid, cycled unit through test and all functions are working properly"
We serviced a
JENN-AIR OVEN
Model JJW2827IL01
Near Easley, SC 29642
Frank
Job Details:
08/09/2023
F1e1 error code.. needs Copernicus board upper and lower oven.; ordrng 2 W11448962 (Control board s)s and 1 Jobcodel14 (Job code l14) and 1 Walldolly (Wall dolly)
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Greenville, SC 29607
Jerry D.
Job Details:
08/09/2023
"Motor inoperable, serv bulletin, ordering, j13; ordrng 1 W11629911 (Cntrl) and 1 W11345228 (Sump and motor)"
We serviced a
KITCHENAID M/W OTR
Model KMLS311HSS09
Near Simpsonville, SC 29681
Jerry D.
Job Details:
08/09/2023
"Plate broken support and ring melted, ordering, j13; ordrng 1 W11387723 (Ring) and 1 W11401221 (Turntable) and 1 W11387721 (Driver) and 1 W11096347 (Seal) and 1 W10466420 (Motor)"
We serviced a
WHIRLPOOL RANGE
Model WCG97US0HS05
Near Simpsonville, SC 29681
Carl
Job Details:
08/09/2023
Needed duel center valve n15; ordrng 1 W11246817 (Valve duel)
We serviced a
MAYTAG DRYER
Model MED3500FW0
Near Canton, NC 28716
Kari
Job Details:
08/08/2023
Installed part unit checks OK had Office run CC for remaining balance of $197.61 an email receipt unit checks OK
We serviced a
WHIRLPOOL FREEZER
Model KRSC503EBS01
Near Taylors, SC 29687
Chris
Job Details:
08/08/2023
Unit has shorted led module. Gave customer a bluebook estimate with tax and shipping at $430.87. Customer denied repair
We serviced a
WHIRLPOOL DRYER
Model WED5620HW2
Near Greer, SC 29651
Chris
Job Details:
08/08/2023
Installed new parts. Unit check is ok . W184g51nl2
We serviced a
JENN AIR REFRIGERATOR
Model JFC2290REP00
Near Cullowhee, NC 28723
Kari
Job Details:
08/08/2023
"Took quick pics found a slab of ice on the bottom of the freezer found that the drain pan was dry underneath took drain tube off to see if there was anything blocking it. A little bit of lint came out but not a whole bunch. Took freezer apart to clear ice from evaporator tray and found a ball of ice covering the cap tube and suction line. The evaporator had a full frost pattern. Air is leaking from ff gaskets, found magnet exposed on right ff door and the flaps that overlay the mullion are ripped. Need gaskets for repair ; ordrng 1 W10830046 (FF door gasket grey) and 1 N15 (Job code)"
We serviced a
KITCHEN AID OVEN
Model KFGD500ESS04
Near Columbus, NC 28722
Derek
Job Details:
08/08/2023
Installed igniter. Cycled bake. Unit heating properly. Unit checks ok.
We serviced a
MAYTAG DRYER
Model MED6500MBK0
Near Pelzer, SC 29669
Jerry D.
Job Details:
08/08/2023
"Cycled unit through test and installed drum ok, temps are 120 and 187, temps chks ok"
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Mars Hill, NC 28754
Derek
Job Details:
08/08/2023
"Found unit not allowing deep fill setting customer states she gets more water on normal than deep fill bulky. Also states unit started a cycle on its own with no one in room. Cycled diagnostics. No faults. Cycled hot and cold fill. Cold moderate fill hot very slow fill. Unit needs control, water level switch, and valve. Will order. L14; ordrng 1 W11608056 (ACU) and 1 WPW10285511 (Switch)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Saluda, NC 28773
Brian
Job Details:
08/08/2023
Found ice bin and ice bin coupler broken. Ice bin (W11347840) chute (W11573761) and coupler (WP2220458) needed. ; ordrng 1 W11347840 (Ice bin) and 1 W11573761 (Chute) and 1 WP2220458 (Coupler) and 1 F12 (Job code)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ02
Near Fountain Inn, SC 29644
Carl
Job Details:
08/08/2023
Installed new valve cycled unit tock operation unit ck ok
We serviced a
MAYTAG WASHER
Model MVWC465HW4
Near Simpsonville, SC 29681
Carl
Job Details:
08/08/2023
Found spluch worn and belt slipping installed new spluch and belt ran diagnostics and a test cycle to ck operation unit ck ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT313CZLZ00
Near Brevard, NC 28712
Brian
Job Details:
08/08/2023
Found evap drain frozen over. I found holes that screws that hold evaporator cover stripped. Screws will not stay in place. Removed all ice build up. Contacted tech support and spoke to Steve. I informed him of the screw hole issue and he said that would make unit non repairable. I recommend customer contact whirlpool and discuss the situation with them. Customer understood. Sr number (7737046347)
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Brevard, NC 28712
Brian
Job Details:
08/08/2023
"Found zero airflow and unit not level. Shorted vent line and ensured it was not kinked. Also leveled unit. At this time, all operations ok with no leaks detected."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ04
Near Greenville, SC 29615
Chris
Job Details:
08/08/2023
Customer asks for filter to be changed. Customer provided own filter. Changed filter for customer . Unit check is ok . No leaks
We serviced a
KITCHEN AID ICE MACHINE
Model KUIX535HBS00
Near Greer, SC 29650
Chris
Job Details:
08/08/2023
Installed new parts. Unit check is ok. No leaks .Called trade care and spoke with Debra. Debra advised she cant give another authorization due to one issued on 6/23. Debra also advised call is eligible for another labor authorization through claims department but trade care isnt required to give one. When filing claim we can claim for another labor authorization. Sr number is 7731821225
We serviced a
KITCHENAID REFRIGERATOR
Model WRF757SDHZ04
Near Greer, SC 29650
Chris
Job Details:
08/08/2023
Installed new parts. Unit check is ok .called trade care and spoke with essy. New labor authorization for failed parts is k1849b0nl1
We serviced a
KITCHENAID M/W OTR
Model KMHC319ESS06
Near Greer, SC 29651
Chris
Job Details:
08/08/2023
Installed new door. Unit check is ok
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Mill Spring, NC 28756
Derek
Job Details:
08/08/2023
Found open cold solenoid and unit not able to fill with cold water. Replaced valve from stock. Cycled unit. Unit checks ok. ; used 1 W11210459 (Valve) from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Greer, SC 29651
Chris
Job Details:
08/08/2023
Unit has partial frost pattern on evap. Compressor runs. Ordering parts for repair ; ordrng 1 W11580057 (Compressor) and 1 R600 and 1 Tap and 1 Drierfilter and 1 S17
We serviced a
WHIRLPOOL RANGE
Model WFE510S0AS0
Near Brevard, NC 28712
Brian
Job Details:
08/08/2023
"Customer said front right burner got very hot when set to medium setting. I tested unit and found it working at this time. Informed customer that according to what she described, a new RF switch (WP3149400) would be needed. Quoted customer 305.24. Customer did not wish to proceed with repairs at this time. Collected 125 for service call."
We serviced a
JENN-AIR MICROWAVE
Model JMC2430IL03
Near Fountain Inn, SC 29644
Carl
Job Details:
08/08/2023
Istalled new board and set model and ser#cycled unit ck ok
We serviced a
WHIRLPOOL WASHER
Model MVW5430MW0
Near Franklin, NC 28734
Kari
Job Details:
08/08/2023
"Took quicklpics in foundunit showing an 8-1 error code found that the customer has now put on a secondary filter system to catch the sentiment coming from the well and its not filling with cold water found that this solenoid had too much dirt collected in it before she put the filter on, Now it just barely dribbles water through all the filtration systems are clean installed new water valve ran unit through a quick wash and a normal cycle just to make sure that it was going to fill properly and move over to rinse switch it does unit checks OK; used 1 W11513255 (Valve) from stock"
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Franklin, NC 28734
Kari
Job Details:
08/08/2023
"Took quick pics found unit Making a horrible noise when its agitating found at the feet of been a little bit too low and the bottom was dragging on the floor as it was spinning its cause damage to the upper cam making the ring slide around as the pulley is moving around installed new cam raised feet unit checks, OK; used 1 W10721967 (Cam) from stock"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ00
Near Cedar Mountain, NC 28718
Brian
Job Details:
08/08/2023
"Installed all parts ordered, according to service pointer. Tested ice maker and found it ok. All fans working and evaporator forming good frost pattern. At this time, all operations ok with no leaks detected."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDHV03
Near Mauldin, SC 29662
Carl
Job Details:
08/08/2023
Unit in vac used uv light to see if there was a leak found at drier filter or evap condenser connection points replace dryer filter pulled 30 min vac no leak down istalled 5.25 oz r134a cycled unit on got good frost on evap unit ck ok but did call tech line talked to joe cus i did or what i thought was dye from the cap tube inside the cabinet coming out of but think it eas spray from dryer/ filter
We serviced a
JENN-AIR OVEN
Model JJW2430WS02
Near Zirconia, NC 28790
Derek
Job Details:
08/08/2023
Found unit giving F2E1 key pad error. Power cycle did not correct error. Gave customer an estimate to replace panel of $1891.08. Customer does not want to repair. Balance would be $1741.08.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Simpsonville, SC 29680
Matt
Job Details:
08/08/2023
Found food freezing in fresh food section. Replaced thermistor and ui control. All functions pass in test mode.
We serviced a
MAYTAG WASHER
Model WTW5010LW0
Near Spartanburg, SC 29303
Cliff
Job Details:
08/08/2023
"Capacitor is bad and the gearcase is leaking oil, ordering parts. Unable to get washplate out will have to bust out.; ordrng 1 U18jobcode (U18 job code) and 1 W11449840 (Gearcase) and 1 W11395618 (Capacitor) and 1 W10752283 (Washplate)"
We serviced a
WHIRLPOOL WASHER
Model MVW5430MW0
Near Cowpens, SC 29330
Cliff
Job Details:
08/08/2023
"Found the nut had come loose from original pulley, replaced cam kit, cycled unit on a drain and spin, all functions check ok"
We serviced a
FRIGIDAIRE DISHWASHER
Model FDSH450LAF4A
Near Simpsonville, SC 29680
Matt
Job Details:
08/08/2023
Found concealed damage. Door had a dying under protective film; ordrng 1 Pleasecheckbeforescheduling (Please check before scheduling) and 1 J13jobcode (J13 job code) and 1 117495104 (Outer door) and 1 Anytech (Any tech)
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Fountain Inn, SC 29644
Matt
Job Details:
08/08/2023
"Replaced outer tub, checked operation, all functions pass. Double labor authorization W184bk1nl2"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Spartanburg, SC 29307
Cliff
Job Details:
08/08/2023
"Unit is intermittently making ice, heater is receiving 120vac, the freezer temp is -2 set to 0, fresh food was 36 set to 35, the ice maker cycles and fills with water, right now the unit is making ice, found no errors in test 56, reset unit, all functions check ok."
We serviced a
WHIRLPOOL RANGE
Model MVW6230RHW2
Near Inman, SC 29349
Cliff
Job Details:
08/08/2023
"Replaced parts, I ran a calibration cycle and a drain and spin for a few minutes to test operation, all functions check ok."
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706ESS05
Near Hendersonville, NC 28792
Derek
Job Details:
08/08/2023
Installed parts. Pulled vacuum. Charged unit with recommended charge per data tag. Cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Hendersonville, NC 28792
Derek
Job Details:
08/08/2023
Installed parts. Cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Inman, SC 29349
Cliff
Job Details:
08/08/2023
"The air damper when opening makes a loud noise. Also the water pressure is extremely low coming from water dispenser, took the filter out and it is still low, checked pressure coming from house and it was good, but the water had a good bit of debris in it, which may have clogged the valves, advised on trying to clear the line out and will order parts.; ordrng 1 W11236851 (Damper) and 1 W11512399 (Isolation valve) and 1 WPW10341320 (Dual valve) and 1 WPW10394053 (Filter assembly) and 1 N15jobcode (N15 job code)"
We serviced a
WHIRLPOOL WASHER
Model WFW94HEXW2
Near Greenville, SC 29609
Cliff
Job Details:
08/08/2023
"Replaced pump, cycled the drain and spin, pump drained water out."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Travelers Rest, SC 29690
Cliff
Job Details:
08/08/2023
"Cam grinding. Replaced parts, ran an auto test, all functions check ok"
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW0
Near Franklin, NC 28734
Kari
Job Details:
08/08/2023
"Took quick pics, found unit showing a 9-1 drain error, took console off and can smell electrical burn. Ohmed out drain pump. Found it showing 2.5 ohms, drain pump has a dead short and it shorted out the drain circuit in the control. Would need both for repair. Customer has authorization for Labor only. Would owe $462.17 for parts. Called techline spoke with Andrew 7737040516 he noted everything and told me to report it to safety spoke with safety team and they issued a new authorization W1846K0WPL1 This covered parts and labor. Safety SR# 7736817123 installed control and drain pump, ran through regular cycle, drain and spin and diagnostics cycle. Unit checks ok. ; used 1 W11396717 (Drain pump) from stock"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFC704FBS04
Near Powdersville, SC 29673
Matt
Job Details:
08/08/2023
Freezer at 2 degrees refrigerator at 40 degrees. Evaporator fan runs through diagnostics but not during normal cooling when inside refrigerator compartment is at 55 set to 37.; ordrng 1 W11574767 (Door u.i.) and 1 W11610999 (Evap cover assembly) and 1 N15jobcode (N15 job code) and 1 Maonly (Ma only)
We serviced a
KITCHEN AID REFRIGERATOR
Model KRSC703HPS00
Near Six Mile, SC 29682
Frank
Job Details:
08/08/2023
Wire harness from door un repairable.. needs door... W11390104 623.30. Labor 2 man job 150x2. 125. 1048.30. Plus tax. Declining job will call back if want it done.
We serviced a
AMANA DRYER
Model NED4655EW1
Near Cashiers, NC 28717
Frank
Job Details:
08/08/2023
Found plug loose.. needs new outlet
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT518SZFB02
Near Sapphire, NC 28774
Frank
Job Details:
08/08/2023
Customer had switch tried to replace. Wires too short inside. Called Techline.. file 7737038404
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Simpsonville, SC 29680
Jerry D.
Job Details:
08/08/2023
"Found motor humming, installed capacitor, found drain pump code, installed connectors, cycled unit through test and all functions are working properly"
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Simpsonville, SC 29680
Jerry D.
Job Details:
08/08/2023
"Found dispenser clogged, cleared dispenser, adjusted leveled unit, suspension holders, unit chks ok"
We serviced a
WHIRLPOOL DRYER
Model WED8200YW0
Near Fountain Inn, SC 29644
Jerry D.
Job Details:
08/08/2023
"Pulley bad installed pulley sent preid, office run card , 365.00"
We serviced a
KITCHEN AID OVEN
Model KEMS308SSS04
Near Simpsonville, SC 29681
Jerry D.
Job Details:
08/08/2023
"No pwer to bake or broil , relay inoperable, estimate, 798.00, customer doesnt want repair, office run card, 125.00"
We serviced a
WHIRLPOOL DISHWASHER
Model WDP560HAMZ0
Near Piedmont, SC 29673
Jerry D.
Job Details:
08/08/2023
"Pump leaking ordering, j13; ordrng 1 W11525546 (Sump and pump)"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF507HPS00
Near Piedmont, SC 29673
Jerry D.
Job Details:
08/08/2023
"Te,ps 36@1, Installed listed parts cycled unit through test and harvest and fill chks ok"
We serviced a
WHIRLPOOL DRYER
Model WED9600TA1
Near Taylors, SC 29687
Chris
Job Details:
08/08/2023
Unit has f70 faults. Unit needs display UI. Parts are unavailable and discontinued for this model . Unit is unrepairable .
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Canton, NC 28716
Kari
Job Details:
08/08/2023
Installed parts unit checks ok; used 1 W11158830 (Capacitor) from stock