We serviced a
WHIRLPOOL WASHER
Model WFW5605MW1
Near Greenville, SC 29615
Chris
Job Details:
01/05/2024
Customer states unit doesnt spin out clothes . Unit has f8 fault stored . Ran step 12 . Unit did not fill . Tech sheet is missing manual diagnostic commands.Unit has broken cold water valve. Ordering for repair ; ordrng 1 2man and 1 Q16 and 1 W11316255 (Valve) and 1 W11316256 (Valve)
We serviced a
JENN-AIR OVEN
Model JJW2830IL00
Near Seneca, SC 29672
Frank
Job Details:
01/05/2024
Gate code 2012..!Reley shorted on Copernicus board (left) board. Burnt wiring.. needs board was changed April 2023. under warranty. Needs wire harness. Bb quoting $612 total paid 306$ owe 306.. ; ordrng 1 W11448962 (Control board) and 1 W11216673 (Main wire harness) and 1 Jobcodew19 (Job code w19)
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Seneca, SC 29672
Frank
Job Details:
01/05/2024
Agitator stripped out on shaft not agitating; ordrng 1 WP3951744 (Agitator) and 1 Jobcodej13 (Job code j13)
We serviced a
WHIRLPOOL DISHWASHER
Model WDF540PADM3
Near Pendleton, SC 29670
Jerry D.
Job Details:
01/05/2024
"Found cntrl getting good volts and polarity inoperable, installed cntrl sent preid cycled unit through test and unit checks ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ06
Near Anderson, SC 29625
Jerry D.
Job Details:
01/05/2024
"Installed door sent preid, cycled unit through test and no leaks found unit checks ok"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Simpsonville, SC 29680
Carl
Job Details:
01/05/2024
Ran diagnostics found no error codes and a test cycle to ck operation found cold water vave shut off turn on cycled unit ckok
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS09
Near Woodfin, NC 28804
Kari
Job Details:
01/05/2024
"Took quick pics, found units hood bulb exploded in the bottom of the unit. I installed new parts and cleared glass shards. Unit checks ok"
We serviced a
KITCHENAID M/W OTR
Model KMHS120ESS5
Near Piedmont, SC 29673
Jerry D.
Job Details:
01/05/2024
Mr called back said he needs to cancel
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Piedmont, SC 29673
Jerry D.
Job Details:
01/05/2024
Mrs called back said another company is on the way with the parts to repair
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Swannanoa, NC 28778
Kari
Job Details:
01/05/2024
"Took quick pics, found door hard to open and close. Found the clasp too tight. Put in new catch. Screen doesnt sit flush on the top due to the plastic being warped. Need new for repair. ; ordrng 1 W11603116 (Screen) and 1 Joecanyoushiptocustomer (If not I can drop off) and 1 F12 (Job code)"
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Seneca, SC 29678
Frank
Job Details:
01/05/2024
No errors.. wouldn't go into spin .. replaced actuator tested working ok; ordrng 1 W11481722 (Actuator)
We serviced a
WHIRLPOOL DRYER
Model med4500mw0
Near Waynesville, NC 28786
Kari
Job Details:
01/04/2024
"Took quick pics, found unit not heating and will just tumble the drum, found hi limit thermal blown duct to the exhaust tube being crushed. Fixed exhaust and replaced thermal. Unit checks ok; used 1 W10900067 (Thermal) from stock"
We serviced a
KITCHENAID RANGE
Model KFED500EBS05
Near Inman, SC 29349
Matt
Job Details:
01/04/2024
Found no display and no operation. Found loose connection at neutral. Corrected connection and re tested. All functions pass.
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Waynesville, NC 28786
Kari
Job Details:
01/04/2024
"Took quick pics, found unit not spinning the clothes out all the way and unit makes a squealing noise in spin and customer states its gotten louder over time, especially on. Heavy loads theyre having to run drain and spin before they put them in the dryer. Need gearcase for repair ; ordrng 1 W11449840 (Gearcase) and 1 N15 (Job code) and 1 W10721967 (Cam)"
We serviced a
WHIRLPOOL DISHWASHER
Model KDTM404KPS2
Near Easley, SC 29640
Sam
Job Details:
01/04/2024
Found units tub leaking at seam will order tub.; ordrng 1 W11409866 (Tub)
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS09
Near Seneca, SC 29678
Frank
Job Details:
01/04/2024
Replaced magnetron and transformer.. checked for loose screws and checked rest of cabinet.. re installed tested working ok. Not vibrating
We serviced a
KITCHENAID DISHWASHER
Model KUDS01FLBT3
Near Greenwood, SC 29646
Jerry D.
Job Details:
01/04/2024
"On arrival customer stated he has had several service companies out on this unit for this problem, customer doesnt want repairs he wants unit replaced, outer wooden door panel is warped and has severe water damage at top left vent area, he says no cabinet maker will make him a new panel, he wants a new ss panel to replace the wooden panel, not sure thats possible, unit is 20 years old, also tub is broken and door closers, most parts are no longer available"
We serviced a
WHIRLPOOL RANGE
Model WFE505W0JZ3
Near Greenwood, SC 29649
Jerry D.
Job Details:
01/04/2024
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Greenwood, SC 29646
Jerry D.
Job Details:
01/04/2024
Installed listed parts cycled unit through test and all functions are working properly
We serviced a
WHIRLPOOL RANGE
Model WFE505W0JZ3
Near Walhalla, SC 29691
Frank
Job Details:
01/04/2024
Re seated door gasket.. tested working ok..
We serviced a
MAYTAG WASHER
Model MVWC565FW1
Near Greenwood, SC 29646
Jerry D.
Job Details:
01/04/2024
"Badket and suspension broken, ordering, Q16; ordrng 1 Q16 (Q16) and 1 W11033491 (Damper) and 1 W10396887 (Hub) and 1 W10586077 (Basket) and 1 W10402178 (Retainer)"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Greenwood, SC 29646
Jerry D.
Job Details:
01/04/2024
"Basket is broken, and dispenser, ordering, Q16; ordrng 1 Q16 (Q16) and 1 W11178227 (Basket) and 1 W11175768 (Bezel)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ11
Near Hendersonville, NC 28791
Brian
Job Details:
01/04/2024
"Found ice bin full and cubes intact. Tested dispenser and found cubes coming out whole. Auger motor and solenoid functioning ok. Temps and water flow ok. Unit working as designed. I informed customer that some chips of ice, when cube is selected, is normal due to temperature fluctuations and various other reasons but it is to be expected. Customer understood. At this time, all operations ok with no leaks detected. Did not move unit."
We serviced a
KITCHENAID REFRIGERATOR
Model KBFN506ESS01
Near Hendersonville, NC 28739
Brian
Job Details:
01/04/2024
Installed all new lights in freezer and fresh food section. Found all operations ok at this time with no leaks detected. Did not move unit
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Arden, NC 28704
Brian
Job Details:
01/04/2024
"Found F5e2 (door switch) and f5e1 (door switch) error codes. Found buttons above vent not responding. Inspected and found gasket for vent not on properly, causing moisture to enter user interface. New Vent (W11649995) bezel (W11545290) user interface (W11622500) and latch (W11412299) needed. ; ordrng 1 W11649995 (Vent) and 1 W11545290 (Bezel) and 1 W11622500 (User interface) and 1 W11412299 (Latch) and 1 L14 (Job code)"
We serviced a
WHIRLPOOL WASHER
Model wtw4855hw3
Near Fountain Inn, SC 29644
Carl
Job Details:
01/04/2024
Installed new tub cycled unit ck ok
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW3
Near Simpsonville, SC 29681
Carl
Job Details:
01/04/2024
Tryed to remove inner tub could not remve with out damaging gearcase and or the outter tub ; ordrng 1 W11219115 (Outter tub) and 1 W11449840 (Gearcase)
We serviced a
MAYTAG WASHER
Model mvw4505mw1
Near Easley, SC 29640
Sam
Job Details:
01/04/2024
Installed latch unit now progresses through cycle completely. All functions pass.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT518SZFM02
Near Greenwood, SC 29646
Jerry D.
Job Details:
01/04/2024
"Cabinet is tweeked unit is level but refrigerator door is way off not sealing, found bottom fresh hinge bent down screws are stripped no way to get door up, Tline, brandon, 3:30, not repairable , 7738166416"
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Easley, SC 29640
Sam
Job Details:
01/04/2024
Found unit with loud scraping noise will order parts.; ordrng 1 279827 (Motor) and 1 WP694089 (Blower wheel) and 1 4392065 (Dryer repair kit)
We serviced a
WHIRLPOOL WASHER
Model MVW4505MW0
Near Easley, SC 29640
Sam
Job Details:
01/04/2024
Installed outer tub cycled unit through quick wash. No leaks all functions pass. Extra labor authorization m19x3a0nl1.5
We serviced a
MAYTAG DRYER
Model MED6500MW0
Near Clyde, NC 28721
Kari
Job Details:
01/04/2024
Installed parts unit checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ0
Near Clyde, NC 28721
Kari
Job Details:
01/04/2024
"Took quick pics, found unit showing 91 and 92 drain errors found when you hit the cancel button you cant hear anything and it doesnt feel like the motors actually running vacuumed out all water could not find any blockages within the drain lines installed new drain pump ran diagnostic cycle unit checks OK"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF540PADM3
Near Seneca, SC 29678
Frank
Job Details:
01/04/2024
Pump not coming on.. error 4/3. 7/1 .. replaced pump and motor tested working ok..
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Clyde, NC 28721
Kari
Job Details:
01/04/2024
"Took quick pics, found unit not making ice in ref. Found test 56 showing E5 thermistor out of range. Found unit would cycle. Installed new cycle. Cycle and filled. Unit checks ok"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ1
Near Travelers Rest, SC 29690
Derek
Job Details:
01/04/2024
Installed parts and cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Travelers Rest, SC 29690
Derek
Job Details:
01/04/2024
Found thermal cutoff fuse open and unit not heating. Replaced fuse and cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HZ0
Near Walhalla, SC 29691
Frank
Job Details:
01/04/2024
Old door doesn't have protective film from inner door to glass causing splatter to get on glass
We serviced a
MAYTAG WASHER
Model MHW8100DW0
Near Seneca, SC 29672
Frank
Job Details:
01/04/2024
Installed detergent cartridge and sensor.. tested working ok
We serviced a
KITCHENAID RANGE
Model KSGG700ESS3
Near Seneca, SC 29672
Frank
Job Details:
01/04/2024
Replaced console.. tested functions. All working ok
We serviced a
WHIRLPOOL DRYER
Model wed4815ew1
Near Easley, SC 29640
Sam
Job Details:
01/04/2024
"Found unit not starting when clicking start button, found loose connection on start switch fixed loose connection. Cycled unit, unit functioning normally now. Checks ok."
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Travelers Rest, SC 29690
Derek
Job Details:
01/04/2024
Installed parts. Cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ11
Near Greenville, SC 29617
Derek
Job Details:
01/04/2024
Installed part. Cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL FREEZER
Model WRS555SIHZ06
Near Greenville, SC 29615
Derek
Job Details:
01/04/2024
Installed parts. Pulled vacuum. Charged unit with recommended charge per data tag. Cycled unit. Unit cooling. Checks ok.
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Waynesville, NC 28786
Kari
Job Details:
01/04/2024
"Took quick pics, found unit not spinning the clothes out all the way and unit makes a squealing noise in spin and customer states its gotten louder over time, especially on. Heavy loads theyre having to run drain and spin before they put them in the dryer. Need gearcase for repair ; ordrng 1 W11449840 (Gearcase) and 1 N15 (Job code) and 1 W10721967 (Cam)"
We serviced a
WHIRLPOOL WASHER
Model WTW7500GC2
Near Lyman, SC 29365
Matt
Job Details:
01/04/2024
"Found error code F7E5 stored in control. Cleared code and ran a diagnostic cycle. Unit will need slider,clutch, gear case and wash plate; ordrng 1 W10752283 (Wash plate) and 1 W10734521 (Slider) and 1 W10754448 (Clutch) and 1 L14jobcode (L14 job code) and 1 Anytech (Any tech) and 1 Needsapproval (Needs approval) and 1 W11393685 (Gear case)"
We serviced a
WHIRLPOOL FREEZER
Model KRMF706ESS05
Near Spartanburg, SC 29301
Matt
Job Details:
01/04/2024
Found freezer at 0 degrees and fresh food section at 34 degrees. Ice level sensor passed. Door switches passed. Found no ice maker error codes. Cycled ice maker and it cycled properly. Tried to fill ice maker with water in test 45 and found fill nozzle frozen. Activated heater in test 19 for a few minutes and re tested. Unit now fills with water. Will order new control. Tech sheet shows aurora board is what powers the heater.; ordrng 1 W10804160 (Aurora board) and 1 WPW10675033 (Main control) and 1 J13jobcode (J13 job code) and 1 Anytech (Any tech)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Spartanburg, SC 29307
Matt
Job Details:
01/04/2024
"Evacuated system. Replaced compressor, pulled a vacuum and weighed in 2.4ounces of r600a. All functions pass."
We serviced a
WHIRLPOOL COOKTOP
Model wfe535s0lz3
Near Easley, SC 29640
Sam
Job Details:
01/04/2024
"Found unit with wrong control board installed, unit has warm zone burner but no button on control for warm zone will order control.; ordrng 1 W11548749 (Control)"
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Honea Path, SC 29654
Jerry D.
Job Details:
01/04/2024
"Found unit keeps filling to overflow then shuts down, volts and polarity good, ordering, j13; ordrng 1 W11491433 (Cntrl)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFC300ESS07
Near Simpsonville, SC 29680
Derek
Job Details:
01/04/2024
Unit shows freezer is 90? with temp alarm on and actual temp close to 0. Frost is forming in freezer but no air leak found. Fresh food set to 46? running in the 40s. Fresh food thermistor reading 4800 ohms 45? freezer thermistor showing 4100 55?. Per Leon with TECHLINE freezer thermistor out of range. Unit compensating by running freezer temp too low affecting ff temp and causing frost in freezer. Will have to thaw water lines when returning. SR 7737987439; ordrng 1 W10316760 (Thermistor)
We serviced a
WHIRLPOOL OVEN
Model WEG745H0LZ1
Near Belton, SC 29627
Jerry D.
Job Details:
01/04/2024
"Customer stated they had a power surge at there house, and the stove quit working, found no power fron controller to bake or broil, estimate 986.00 customer doesnt want repair, 150.00"
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Arden, NC 28704
Brian
Job Details:
01/04/2024
"Installed new wash motor. Tested unit observing for leaks and proper functions. At this time, all operations ok with no leaks detected."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Arden, NC 28704
Brian
Job Details:
01/04/2024
"Installed new agitator. Recalibrated and tested unit. Unit itself is ok, however I found no hot water going to unit and drain hose attached to another hose laying in the floor. Informed customer that unit needs hot and cold valves connected to unit and drain hose should be in a stand pipe, to allow for proper draining. Referred customer to use and care guide."
We serviced a
WHIRLPOOL DRYER
Model MED4500MW0
Near Canton, NC 28716
Kari
Job Details:
01/04/2024
"Took quick pics, found unit not heating on either setting. Found the hi limit thermal blown. Installed new. Unit checks ok."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Candler, NC 28715
Kari
Job Details:
01/04/2024
Installed parts unit checks ok
We serviced a
WHIRLPOOL RANGE
Model WOD51EC0HS20
Near Boiling Springs, SC 29316
Sam
Job Details:
01/03/2024
Installed blower on unit. Heated unit to 400 in both ovens. Unit heats. All lights working on unit. Both fans working and sound good. All components working as designed now. All functions pass. Collected rest of estimate of 481.00. Job complete.
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ2
Near Pelzer, SC 29669
Jerry D.
Job Details:
01/03/2024
Installed listed parts cycled unit through test and no leaks found unit checks ok
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Marshall, NC 28753
Kari
Job Details:
01/03/2024
"Installed parts and ran unit through drain and spin until done, and also I ran it through and entire quick wash until it said done and unlocked lid. Unit checks ok labor auth W19WPM0NPL1.5"
We serviced a
WHIRLPOOL RANGE
Model WFG535S0LZ4
Near Seneca, SC 29678
Frank
Job Details:
01/03/2024
Will click and light then keeps clicking shutting off gas. Re lights then shutting off.; ordrng 1 W11162730 (Dsi board) and 1 W11620570 (Control board) and 1 W11645866 (Bake harness) and 1 Jobcodel14 (Job code l14)
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Spartanburg, SC 29302
Derek
Job Details:
01/03/2024
Found unit will intermittently have a cluster of keys which dont respond. Panel replacement recently corrected issue for around a month before same issue returned. Witnessed failure at time of repair with normal key. Power cycle will sometimes correct issue. No errors stored. When keys respond and unit starts it completes cycle normally. Will order parts. L14; ordrng 1 W11622490 (UI) and 1 W11629911 (ACU)
We serviced a
KITCHEN AID RANGE
Model KSGB900ESS8
Near Moore, SC 29369
Sam
Job Details:
01/03/2024
"Units bake igniting intermittently. Found metal piece to igniter bent not allowing igniter to spark and ignite the gas coming from glow bar. Adjusted metal piece of igniter, unit is now igniting properly every time. All functions pass."
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Marshall, NC 28753
Kari
Job Details:
01/03/2024
"Took quick pics, found unit making excessive noise found the unit is sitting on tile and two of the feet are right between the tiles found. Those 2 feet had flat spots in the rubber was causing some shaking. Also found there is some noise coming from the gear case so when I took the cam down, theres black oil in the top of the cam pulley will need gear case to complete repair also will need suspension due to the fact when you push on the term, it bounces too much and it has a hard time slowing down; ordrng 1 W11449840 (Gearcase) and 1 Q16 (Job code) and 1 W11130362 (Suspension), used 1 W11213957 (Feet) from stock"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Mars Hill, NC 28754
Kari
Job Details:
01/03/2024
"Took quick pics, found unit shutting off during agitate and spin and when the motor ramps up you can see the lights flicking and going on. Installed new shifter. Found that the water valve is clogged with sediment. Installed new valve. Unit now fills properly will need control for repair ; ordrng 1 W11603810 (Control) and 1 J13 (Job code), used 1 W10913953 (Shifter) from stock"
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Boiling Springs, SC 29316
Sam
Job Details:
01/03/2024
Found unit with long fill error code. Cycled unit through quick wash found unit not filling with enough water checked pressure tube. Pressure tube checks ok. Units valve sounds scratchy and not putting in enough water during cycle. Will order valve and control.; ordrng 1 W11626074 (Control) and 1 W11513255 (Control)
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHS2
Near Pendleton, SC 29670
Frank
Job Details:
01/03/2024
Found unit off leveled. Door hitting cabinet.. leveled legs re mounted brackets.. all good now.. open and close ok
We serviced a
MAYTAG WASHER
Model MHW5630HW0
Near Easley, SC 29642
Frank
Job Details:
01/03/2024
Found rip in door gasket. Causing leak. F8e1 error. F0 e5 f5e2 f0e2 f0e1.. ordering switch for f8e1 error.. stacked unit need 2 man.. ; ordrng 1 W11316246 (Pressure switch) and 1 W11314648 (Bellows) and 1 W11322901 (Control unit) and 1 Jobcodeq16 (Job code q16)
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Easley, SC 29640
Frank
Job Details:
01/03/2024
Installed parts.. unable to test not in laundry room.
We serviced a
JENN-AIR REFRIGERATOR
Model JFFCC72EFS04
Near Seneca, SC 29672
Frank
Job Details:
01/03/2024
Ordered wrong part.. need motor ice door. W11189145.. ordering; ordrng 1 W11189145 (Ice door motor)
We serviced a
MAYTAG WASHER
Model MVW6500MBK0
Near Seneca, SC 29678
Frank
Job Details:
01/03/2024
Found pet hair filter clogged.. cleaned checked under wash plate for build up. Ok.. unit running ok mechanical.
We serviced a
MAYTAG WASHER
Model MVW5035MW1
Near Seneca, SC 29678
Frank
Job Details:
01/03/2024
"Replaced motor,, couldn't remove agitator need to be cut out.. decided not to replace gearcase. If cam comes off again need to order agitator with gearcase. Reinforced cam nut with thread lock.."
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Spartanburg, SC 29303
Derek
Job Details:
01/03/2024
Installed parts. Cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT148FZDW04
Near Sapphire, NC 28774
Matt
Job Details:
01/03/2024
Found fresh food section freezing food on warmer setting. Found fresh food thermistor out of range. Replaced fresh food thermistor. Checks o.k
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFC300ESS09
Near Waynesville, NC 28786
Matt
Job Details:
01/03/2024
Found drain pan vibrating. Adjusted drain pan. Checks o.k
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDZ02
Near Sylva, NC 28779
Matt
Job Details:
01/03/2024
Customer hears a wiring noise of the refrigerant traveling through the evaporator. Drier filter is already at a 45 degree angle. Evaporator inlet has also been wrapped in mastic. Called tech line and spoke to Derek. Sending product up for review. File number 7738151634.
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Piedmont, SC 29673
Jerry D.
Job Details:
01/03/2024
"Motor broken off and splutch and belt broken, shield torn up, ordering, j13; ordrng 1 W10677723 (Motor) and 1 W10721967 (Splutch) and 1 W10006384 (Belt) and 1 W11087188 (Shield)"
We serviced a
WHIRLPOOL DRYER
Model WED4616FW0
Near Greenville, SC 29607
Carl
Job Details:
01/03/2024
Installed new timer xyclwdu
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Columbus, NC 28722
Derek
Job Details:
01/03/2024
Installed fan. Cycled unit. Unit checks ok.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Saluda, NC 28773
Brian
Job Details:
01/03/2024
Found crisper drawer warped. Crisper (W11162443) slide (W11676506) housing (WPW10282880); ordrng 1 W11162443 (Crisper) and 1 W11676506 (Slide) and 1 WPW10282880 (Housing) and 1 J13 (Job code)
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Tryon, NC 28782
Brian
Job Details:
01/03/2024
Found F6e3 (communication error) F0e7 (load in washer during wash cycle). Inspected and found rotor bolt loose. Tightened screw and tested. Unit is completing cycle. Found drain hose damaged and leaking. Drain hose (W11244231) screw (W10752189) internal hose (W11553446) drain hose extension (DRNEXT4) hose (40922) needed. ; ordrng 1 W11244231 (Drain hose) and 1 W10752189 (Screw) and 1 W11553446 (Internal hose) and 1 DRNEXT4 (Drain hose extension) and 1 40922 (Hose) and 1 L14 (Job code)
We serviced a
MAYTAG WASHER
Model MVW5430MW0
Near Mill Spring, NC 28756
Brian
Job Details:
01/03/2024
F8e1 (long fill). Tested unit and it would not go into diagnostics test. Found water lines reversed. Corrected and tested again. Unit still wont enter diagnostics. Latch (W11670519) and control (W11627413) needed. ; ordrng 1 W11627413 (Control) and 1 W11670519 (Latch) and 1 J13 (Job code)
We serviced a
MAYTAG DISHWASHER
Model MDB8959SFZ4
Near Lake Lure, NC 28746
Brian
Job Details:
01/03/2024
"Found F6e4 (float switch open) F5e2 (door stuck closed) error codes. Tested unit in diagnostics and found it filling. Tested and found unit not draining. Inspected and found knock out plug, still in disposal. Removed plug and tested. Found all operations ok at this time, with no leaks detected. Collected 160 via check."
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706ESS05
Near Hendersonville, NC 28792
Brian
Job Details:
01/03/2024
Found ice compacted under ice bin. Ice cubes look ok. Removed ice bin and ice buildup up and tested. Found mechanical components ok but found service pointer regarding this issue. New Shaft (W11509548); ordrng 1 W11509548 (Shaft) and 1 J13 (Job code)
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Simpsonville, SC 29680
Jerry D.
Job Details:
01/03/2024
"Motor and blower stripped, ordering, j13; ordrng 1 694089 (Blower) and 1 W10396029 (Motor) and 1 W10131364 (Belt)"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Simpsonville, SC 29680
Jerry D.
Job Details:
01/03/2024
"Spin basket welds broken, agitator stripped, ordering, j13; ordrng 1 W10554251 (Basket) and 1 3951744 (Agitator)"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Simpsonville, SC 29681
Jerry D.
Job Details:
01/03/2024
"Found actuator broken and splutch grinding, installed parts sent preid, cycled unit through test and calibration and unit checks ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ04
Near Simpsonville, SC 29681
Jerry D.
Job Details:
01/03/2024
"Temps 36@1, Found imk motor code, Instaled imk sent preid, cycled imk through test and harvest and fill ok"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFC704FPS01
Near Mauldin, SC 29662
Carl
Job Details:
01/03/2024
Installed new frame and trivet unit ck ok
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF507HPS00
Near Simpsonville, SC 29681
Carl
Job Details:
01/03/2024
Installed led kit cycled unit ck ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDF331PAHS1
Near Fountain Inn, SC 29644
Carl
Job Details:
01/03/2024
Found back flow valve not allowing water to flow freely pushing aginst flow pushed valve forward reinstalled cycled unit got much better flow unit ck ok
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Boiling Springs, SC 29316
Sam
Job Details:
01/03/2024
"Found unit not wanting to put in water on its own ran unit through diagnostics and water worked fine, but in quick wash or normal it will not put water in. Also found f7 e1 error for actuator will order control and water valve for not putting water into unit. And will order actuator for error code that was found.; ordrng 1 W11556725 (Control) and 1 W11220230 (Water valve) and 1 W11481722 (Actuator)"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRSC700HPS04
Near Spartanburg, SC 29306
Derek
Job Details:
01/03/2024
Found defrost drain for fresh food section not draining and water leaking into floor. Unable to clear drain manually. Removed drain and found evap rubber cap removed during manufacturing went down drain and had to be pushed out. Once out draining properly. Unit checks ok.
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Spartanburg, SC 29302
Derek
Job Details:
01/03/2024
Found unit will intermittently have a cluster of keys which dont respond. Panel replacement recently corrected issue for around a month before same issue returned. Witnessed failure at time of repair with normal key. Power cycle will sometimes correct issue. No errors stored. When keys respond and unit starts it completes cycle normally. Will order parts. L14; ordrng 1 W11622490 (UI) and 1 W11629911 (ACU)
We serviced a
KITCHEN AID DISHWASHER
Model KDTE334GBS0
Near Pelzer, SC 29669
Jerry D.
Job Details:
01/03/2024
Installed listed parts cycled unit through test and no leaks found unit checks ok
We serviced a
MAYTAG WASHER
Model MVWX655DW2
Near Boiling Springs, SC 29316
Sam
Job Details:
01/03/2024
Found units suspension rods not correct. Found unit resting on floor with suspension rods installed properly. Unit will need new suspension rods. Gave customer estimate of 382.00 customer denied estimate. Told customer to call us back if he changes his mind. Collected trip charge of 150.00.
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZ0
Near Waynesville, NC 28786
Kari
Job Details:
12/29/2023
Installed parts unit checks ok
We serviced a
KITCHEN AID RANGE
Model KSDB900ESS3
Near Anderson, SC 29621
Jerry D.
Job Details:
12/29/2023
"Interface missing digits, relay on cntrl not sending power to bake element, customer has a 5 year warranty with lowes, if we get the job, parts needed are, w10759278 Cntrl, w10901118 console"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Asheville, NC 28804
Kari
Job Details:
12/29/2023
"Took quick pics, found units ff compartment too col. found diffuser door not fully closing and very loud. Installed new damper unit checks ok"
We serviced a
JENN-AIR MW OVEN COMBO
Model JMW3430DP02
Near Woodfin, NC 28804
Kari
Job Details:
12/29/2023
"Took quick pics, found unit showing 2-1 stuck button key and customer was resetting with breaker until that stopped working now no matter what it beeps and shows that code. Reset breaker to see if I could get it into diagnostics and immediately it started doing the same thing. Gave customer est of $1,670.29. Customer agreed paid by cc and emailed receipt. Installed new panel, made sure microwave and oven are working. Unit checks ok."
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Asheville, NC 28804
Kari
Job Details:
12/29/2023
"Took quick pics found unit showing 72 variable speed, motor rotor locked. Cleared code tried to run unit through diagnostic cycle. It did fill, but then as soon as board went to turn the motor on it started flashing the same 72 code and beeping and wouldnt do anything else in the cycle found that the motor is showing 17 ohms which is out of range according to the tech sheet it should be between 7 and 12 ohms. There is no 11 code present so according to the tech sheet, we would have to replace the motor to fix the issue. Motor assembly is on back order. Customer is unhappy and would like a new one. Provided him with Whirlpools customer service number. Customer refuses repair at this time. Customer also requested the builder send him this information. I called the builder and left a message and he has yet to call me back."